-- ******************************************************************** -- CISCO-CABLE-AVAILABILITY-MIB.my: -- Cisco Cable Availability MIB file for HCCP -- -- May 2001, Sunethra Jawahar -- -- Copyright (c) 2001, 2002 by Cisco Systems, Inc. -- All rights reserved. -- ******************************************************************** -- -- This is the MIB module for management of Hot Standby -- Connection to Connection Protocol (HCCP) features. HCCP is -- Cisco proprietary solution for High System Availability -- for Cable Modem Termination Systems(CMTS). -- -- The HCCP protocol is primarily responsible for failure -- detection and to initiate switchover from one CMTS to -- another. -- -- The CMTS protection is at RF MAC domain level, -- where protecting and working CMTS cable interfaces operate -- on the same downstream and upstream frequency. -- -- HCCP Terminology: -- HCCP group : A set of RF MAC interfaces which communicate using -- HCCP messaging. -- -- HCCP member :Each RF MAC interface configured for HCCP. -- -- Protect : A member in a HCCP group which acts as the -- hot standby and protecting other members. -- -- Working : The member in a HCCP group that is being -- protected. -- -- Thus a 'HCCP group' consists of 'HCCP members' which are -- RF MAC interfaces configured to function as 'Protect' or -- 'Working'. CISCO-CABLE-AVAILABILITY-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, NOTIFICATION-TYPE, OBJECT-TYPE, Integer32, Counter32 FROM SNMPv2-SMI TruthValue, DisplayString FROM SNMPv2-TC SnmpAdminString FROM SNMP-FRAMEWORK-MIB InetAddress, InetAddressType FROM INET-ADDRESS-MIB OBJECT-GROUP, MODULE-COMPLIANCE, NOTIFICATION-GROUP FROM SNMPv2-CONF ifIndex FROM IF-MIB ciscoMgmt FROM CISCO-SMI; ciscoCableAvailabilityMIB MODULE-IDENTITY LAST-UPDATED "200302200000Z" ORGANIZATION "Cisco Systems, Inc." CONTACT-INFO " Cisco Systems Customer Service Postal: Cisco Systems 170 West Tasman Drive San Jose, CA 95134 U.S.A. Phone: +1 800 553-NETS E-mail: cs-ubr@cisco.com" DESCRIPTION "This is the MIB module for management of Hot Standby Connection to Connection Protocol (HCCP) features. HCCP is a Cisco proprietary solution for High System Availability for Cable Modem Termination Systems (CMTS). The HCCP protocol is primarily responsible for failure detection and to initiate switchover from one CMTS to another. The CMTS protection is at the RF mac domain level, where protecting and working CMTS cable interfaces operate on the same downstream and upstream frequency. HCCP Terminology: HCCP group: A set of RF MAC interfaces which communicate using HCCP messaging. HCCP member: Each RF MAC interface configured for HCCP. Protect: A member in a HCCP group which acts as the hot standby and protecting other members. Working: The member in a HCCP group that is being protected. Thus a 'HCCP group' consists of 'HCCP members' which are RF MAC interfaces configured to function as 'Protect' or 'Working'. Some RF mac interfaces are configured to form a 'HCCP group' and members within one 'HCCP group' communicate with each other using HCCP messaging. By HCCP messaging, some member acting as 'Protect' or hot standby can detect a failure on the other members which are designated as 'Working' in the same HCCP group. The 'Protect' can then take over traffic on the failed interface. Protection scenarios can be N+1 or 1+1. In the N+1 protection scenario, there is only one CMTS designated for protection of N CMTS. For example in 1+1 : When one linecard fails, the other automatically takes over its traffic. During normal operation, only one linecard forwards traffic, the other linecard stands by and listens to the messages passed from the active one. While in the standby mode, the linecard does not forward traffic. HCCP will automatically switchover to the standby in cases of software failures (crash), linecard insertion/removal, interface shutdowns and cable wiring failures etc. Both Protect and Working are preconfigured on the CMTS and all HCCP configuration must comply with the actual cable plant deployment for correct operation of the HCCP protocol. This MIB includes objects to support the HCCP feature on the CMTS." REVISION "200302200000Z" DESCRIPTION "Changed range of object ccaHCCPMemChanSwitchPosition and added ciscoCableAvailabilityComplianceRev1 to allow MIN-ACCESS as read-only for the same. " REVISION "200111250000Z" DESCRIPTION "Initial version of this MIB module." ::= { ciscoMgmt 242 } ciscoCableAvailabilityMIBObjects OBJECT IDENTIFIER ::= { ciscoCableAvailabilityMIB 1 } ccaHCCPObjects OBJECT IDENTIFIER ::= { ciscoCableAvailabilityMIBObjects 1 } -- -- ccaHCCPObjects : -- Cisco Cable Availability HCCP (Hot standby Connection to Connection -- protocol) group -- -- This group provides the objects that allow HCCP configuration on -- the CMTS. -- ccaHCCPVersion OBJECT-TYPE SYNTAX INTEGER { others(1), version1(2), version2(3), version3(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "The current version of HCCP features. others(1) : Any other HCCP Version other than the following list. version1(2) : HCCP Version 1.0 supports for 1+1 Availability. (1 RF MAC protecting 1 RF MAC without load sharing on the same upstream and downstream frequencies with DOCSIS1.0+ features) version2(3) : HCCP Version 2.0 supports for 1+1 Availability. (1 RF MAC protecting 1 RF MAC without load sharing on the same upstream and downstream frequencies with DOCSIS1.1 features) version3(4) : HCCP Version 3.0 supports for N+1 Availability. (1 RF MAC protecting N RF MAC without load sharing on different upstream and downstream frequencies with DOCSIS1.1 features)." REFERENCE "Data-Over-Cable Service Interface Specifications (DOCSIS) Radio Frequency Interface Specification" ::= { ccaHCCPObjects 1 } -- -- ccaHCCPGroupTable: -- -- This table provides information about the HCCP groups configured -- on the Cable Modem Termination Systems (CMTS). -- -- Each set of Working along with a Protect form a HCCP group with a -- unique group ID number(1-255) within a domain. Each protection -- group is assigned an identification. Only members within a group are -- allowed to communicate with each other via HCCP messaging. -- Each of them is protected by authentication . -- -- ccaHCCPGroupTable OBJECT-TYPE SYNTAX SEQUENCE OF CcaHCCPGroupEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains information of the HCCP groups on the CMTS. A HCCP group consists of a set of Working along with a Protect and each group is identified by a unique group ID number. Only members within a group are allowed to communicate with each other via HCCP messaging. " ::= { ccaHCCPObjects 2 } ccaHCCPGroupEntry OBJECT-TYPE SYNTAX CcaHCCPGroupEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A set of attributes of a HCCP group on the CMTS. An entry in this table exists for each configured HCCP group on the CMTS." INDEX { ccaHCCPGroupID } ::= { ccaHCCPGroupTable 1 } CcaHCCPGroupEntry ::= SEQUENCE { ccaHCCPGroupID Integer32, ccaHCCPGroupAuthentication INTEGER, ccaHCCPGroupAuthKeyChain SnmpAdminString, ccaHCCPGroupHelloTime Integer32, ccaHCCPGroupHoldTime Integer32, ccaHCCPGroupRevertEnable TruthValue, ccaHCCPGroupProtectIpAddrType InetAddressType, ccaHCCPGroupProtectIpAddress InetAddress } ccaHCCPGroupID OBJECT-TYPE SYNTAX Integer32 (1..255) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Identification of the HCCP protection group. Only members of the same group talk to each other via HCCP messaging." ::= { ccaHCCPGroupEntry 1 } ccaHCCPGroupAuthentication OBJECT-TYPE SYNTAX INTEGER { none(1), md5(2), text(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object specifies the type of authentication method used. none(1) : No authentication is performed on that group. md5(2) : The MD5 Message Digest algorithm. text(3) : Authentication based on a textual string. " REFERENCE "Rivest, R., 'The MD5 Message-Digest Algorithm', RFC1321, MIT LCS & RSA Data Security, Inc., April 1992." ::= { ccaHCCPGroupEntry 2 } ccaHCCPGroupAuthKeyChain OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "This object is the name of a globally configured key chain. It is used to enable authentication and determine the set of keys which may be used on a particular group. If ccaHCCPGroupAuthentication is text(3), it is used as the authentication password. If ccaHCCPGroupAuthentication is md5(2), it is used as the message digest for md5. If a key chain has not been configured, no authentication is performed on that group." ::= { ccaHCCPGroupEntry 3 } ccaHCCPGroupHelloTime OBJECT-TYPE SYNTAX Integer32(333..5000) UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Hello time is the interval(in milliseconds) between consecutive HELLO messages. HELLO is a one-way message in HCCP sent from Protect to all Working in the group. It indicates that Protect is ready to receive data and expects HELLO_ACK. HELLO message indicates the existence and state of Protect. Failing to send this message indicates Protect is not in service." ::= { ccaHCCPGroupEntry 4 } ccaHCCPGroupHoldTime OBJECT-TYPE SYNTAX Integer32(1000..25000) UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Hold time is the interval(in milliseconds) between the time of receiving the last HELLO ACK message and the time to assume that the cable interface is out of service. In the case of Working, it is the interval in milliseconds between the time when the Working receives a HELLO message and the time to assume that Protect has failed. In the case of Protect, it is the interval in milliseconds between the time when the Protect sends last HELLO message without seeing HELLO_ACK and the time to assume that Working has failed. It is carried by HELLO message and is used by Protect and all Working." ::= { ccaHCCPGroupEntry 5 } ccaHCCPGroupRevertEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "Enable or disable the Protect to revert switchover after Working is restored to operation. It can be disabled (default) if user wants to perform some tests before revert switching." ::= { ccaHCCPGroupEntry 6 } ccaHCCPGroupProtectIpAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-only STATUS current DESCRIPTION "The type of internet address of ccaHCCPGroupProtectIpAddress." ::= { ccaHCCPGroupEntry 7 } ccaHCCPGroupProtectIpAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The IP address of the Protect interface for the group that sends the HELLO message. " ::= { ccaHCCPGroupEntry 8 } -- ccaHCCPGroupIfTable -- -- This tables provides the mapping of the RF MAC interfaces on the CMTS -- to its functionality in the HCCP group. -- ccaHCCPGroupIfTable OBJECT-TYPE SYNTAX SEQUENCE OF CcaHCCPGroupIfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides the mapping of the RF MAC interfaces on the CMTS to its functionality in the HCCP group. It indicates if the RF MAC interface has been configured as Protect or as a Working.It provides interface specific configuration and state information as well as statistics." ::= { ccaHCCPObjects 3 } ccaHCCPGroupIfEntry OBJECT-TYPE SYNTAX CcaHCCPGroupIfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A mapping of a RF MAC interface to its configured functionality as Protect or Working. It provides interface specific configuration and state information as well as statistics. Entries in this table exist for each ifEntry with ifType of docsCableUpstream(129)." INDEX { ccaHCCPGroupID , ifIndex } ::= { ccaHCCPGroupIfTable 1 } CcaHCCPGroupIfEntry ::= SEQUENCE { ccaHCCPGroupIfStatus INTEGER, ccaHCCPGroupIfRevertTime Integer32, ccaHCCPGroupIfTrackEnable TruthValue, ccaHCCPGroupIfState INTEGER, ccaHCCPGroupIfLastSwitchReason INTEGER, ccaHCCPGroupIfOnTransitions Counter32, ccaHCCPGroupIfOffTransitions Counter32 } ccaHCCPGroupIfStatus OBJECT-TYPE SYNTAX INTEGER { unknown(1), protect(2), working(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object identifies if the interface is functioning as Working or Protect in the HCCP group." ::= { ccaHCCPGroupIfEntry 1 } ccaHCCPGroupIfRevertTime OBJECT-TYPE SYNTAX Integer32(1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "Revert time used by Working specifies the time interval to wait before automatic revert switching. Within that time interval, manual switchover is allowed to happen." ::= { ccaHCCPGroupIfEntry 2 } ccaHCCPGroupIfTrackEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "Enable or disable failover based on interface state. The interface can be any interface on the router, which is monitored by keep alive timer. If it is set to true, ccaHCCPGroupTrackInterfaceTable contains the list of interfaces that are being tracked. By default the current interface is under tracking." ::= { ccaHCCPGroupIfEntry 3 } ccaHCCPGroupIfState OBJECT-TYPE SYNTAX INTEGER { forwarding(1), blocking(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The current state of the HCCP group. The members can either be forwarding traffic or blocking all traffic. " ::= { ccaHCCPGroupIfEntry 4 } ccaHCCPGroupIfLastSwitchReason OBJECT-TYPE SYNTAX INTEGER { none(1), holdTimeExpire(2), hwIfDown(3), failTest(4), failLinkDown(5), failBundleDown(6), internal(7) } MAX-ACCESS read-only STATUS current DESCRIPTION "The reason for last switch. none(1) : No switchover has occurred. holdTimeExpire(2) : Occurs when HCCP fails to hear HELLO/HELLO_ACK and the hold time expires. hwIfDown(3) : Occurs when the hardware interface is down. (eg shut/no shut) failTest(3) : Failover was CLI initiated or SNMP initiated through ccaHCCPGroupSwitchNow. failLinkDown(4) : Failure in the cable wiring or a hardware interface. failBundleDown(5) : A bundled interface failure. internal(6) : All other failures . " ::= { ccaHCCPGroupIfEntry 5 } ccaHCCPGroupIfOnTransitions OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of times the value of ccaHCCPGroupIfState transitioned from 'blocking' to 'forwarding'." ::= { ccaHCCPGroupIfEntry 6 } ccaHCCPGroupIfOffTransitions OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of times the value of ccaHCCPGroupIfState transitioned from 'forwarding' to 'blocking'. " ::= { ccaHCCPGroupIfEntry 7 } -- -- ccaHCCPGroupTrackInterfaceTable -- -- This table contains the list of all the interfaces that are being -- tracked by this interface in the group. Tracking means enabling -- failover based on interface state. The interface can be any -- interface on the router, which is monitored by keep alive timer. -- ccaHCCPGroupTrackInterfaceTable OBJECT-TYPE SYNTAX SEQUENCE OF CcaHCCPGroupTrackInterfaceEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains the attributes of all the interfaces that are being tracked by this group. The interface can be any interface on the chassis, which is monitored by a keep alive timer." ::= { ccaHCCPObjects 4 } ccaHCCPGroupTrackInterfaceEntry OBJECT-TYPE SYNTAX CcaHCCPGroupTrackInterfaceEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A set of attributes of an interfaces being tracked within a group. " INDEX { ccaHCCPGroupID, ifIndex, ccaHCCPGroupTrackIfID } ::= { ccaHCCPGroupTrackInterfaceTable 1 } CcaHCCPGroupTrackInterfaceEntry ::= SEQUENCE { ccaHCCPGroupTrackIfID Integer32, ccaHCCPGroupTrackIfDescr DisplayString } ccaHCCPGroupTrackIfID OBJECT-TYPE SYNTAX Integer32(1..100) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The value of this object uniquely identifies an interface that is being tracked within this group." ::= { ccaHCCPGroupTrackInterfaceEntry 1 } ccaHCCPGroupTrackIfDescr OBJECT-TYPE SYNTAX DisplayString (SIZE (0..255)) MAX-ACCESS read-only STATUS current DESCRIPTION "A textual string containing information about the interface that is being tracked. This corresponds to the ifDescr of the tracked interface." ::= { ccaHCCPGroupTrackInterfaceEntry 2 } -- -- ccaHCCPMemberTable -- -- Each RF MAC interface configured for HCCP is called a HCCP member. -- This table provides information about the HCCP members on the -- Cable Modem Termination Systems (CMTS). -- Only members within a HCCP group are allowed to communicate with -- each other via HCCP messaging. -- ccaHCCPMemberTable OBJECT-TYPE SYNTAX SEQUENCE OF CcaHCCPMemberEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains the attributes of HCCP members. Each RF MAC interface configured for HCCP is called a HCCP member. Entries in this table are created for all members. In the case of Protect, it gives information of all the Working members under it's protection group. In the case of Working, it gives information about itself." ::= { ccaHCCPObjects 5 } ccaHCCPMemberEntry OBJECT-TYPE SYNTAX CcaHCCPMemberEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A configurable attributes of a HCCP member within a group. " INDEX { ccaHCCPGroupID , ifIndex , ccaHCCPMemberID } ::= { ccaHCCPMemberTable 1 } CcaHCCPMemberEntry ::= SEQUENCE { ccaHCCPMemberID Integer32, ccaHCCPMemberIpAddrType InetAddressType, ccaHCCPMemberIpAddress InetAddress, ccaHCCPMemberState INTEGER, ccaHCCPMemberSwitchNow TruthValue } ccaHCCPMemberID OBJECT-TYPE SYNTAX Integer32 (1..255) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The value of this object identifies the Working member's ID inside a group. Members within the same group are uniquely identified by this ID. The ID can be reused outside the group." ::= { ccaHCCPMemberEntry 1 } ccaHCCPMemberIpAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-only STATUS current DESCRIPTION "The type of internet address of ccaHCCPMemberIpAddress." ::= { ccaHCCPMemberEntry 2 } ccaHCCPMemberIpAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The IP address of the member. If the member functions as Working it represents an IP address on its interface. However in case of Protect, it represents IP address of the Working member that are being protected." ::= { ccaHCCPMemberEntry 3 } ccaHCCPMemberState OBJECT-TYPE SYNTAX INTEGER { active(1), standby(2), nonFunctional(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The current status of to this HCCP group member. If the RF MAC interface is Working, this represents the status of the Working member. active(1) : Working member is forwarding traffic. standby(2) : Working member is blocking traffic. If the RF MAC interface is Protect, this represents the Protect status to this member. active(1) : The Protect is taking over and forwarding the traffic from this Working member which is now blocking. standby(2) : The Protect is standby(blocking). This means that Working member is forwarding traffic and thus works fine. nonFunctional(3): This member is disabled." ::= { ccaHCCPMemberEntry 4 } ccaHCCPMemberSwitchNow OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to initiate the switchover. When it is set to true(1) and this interface is Protect, it will cause the switchover to specified Working member. When it is set to true(1), and if this interface is Working, it will cause the switchover to the Protect in it's protection group. Switchover can thus be initiated by either the Protect or the Working. Reading this object will always return false(2)." ::= { ccaHCCPMemberEntry 5 } -- -- ccaHCCPMemChanSwitchTable : -- -- This table provides information about the HCCP channel switch -- which is used to switch the upstreams and -- downstreams.This table is used to specify the channel switch -- type, the RF switch over group, RF switch module. -- ccaHCCPMemChanSwitchTable OBJECT-TYPE SYNTAX SEQUENCE OF CcaHCCPMemChanSwitchEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This is an adjunct to ccaHCCPMemberTable. It provides information of HCCP member channel switches. It specifies the RF channel switch type, the RF switch over group and the RF switch module. The upconvertor IP addresses can also be retrieved from this table. This table does not exist if no channel switch has been enabled for this member in the group." ::= { ccaHCCPObjects 6 } ccaHCCPMemChanSwitchEntry OBJECT-TYPE SYNTAX CcaHCCPMemChanSwitchEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A set of attributes of the channel switch specifying the channel switch details per member (ccaHCCPMemberID) on an interface (ifType is docsCableMaclayer(127)) of a HCCP group. " INDEX { ccaHCCPGroupID, ifIndex, ccaHCCPMemberID, ccaHCCPMemChanSwitchID } ::= { ccaHCCPMemChanSwitchTable 1 } CcaHCCPMemChanSwitchEntry ::= SEQUENCE { ccaHCCPMemChanSwitchID Integer32, ccaHCCPMemChanSwitchType INTEGER, ccaHCCPMemChanSwitchIpAddrType InetAddressType, ccaHCCPMemChanSwitchIpAddress InetAddress, ccaHCCPMemChanSwitchModule Integer32, ccaHCCPMemChanSwitchProtIpAddrType InetAddressType, ccaHCCPMemChanSwitchProtIpAddr InetAddress, ccaHCCPMemChanSwitchProtModule Integer32, ccaHCCPMemChanSwitchPosition Integer32, ccaHCCPMemChanSwitchSnmpEnable TruthValue } ccaHCCPMemChanSwitchID OBJECT-TYPE SYNTAX Integer32(1..100) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Uniquely identifies the entry for channel switch for a member. The channel switch is the RF component that allows downstream and upstream channel switching." ::= { ccaHCCPMemChanSwitchEntry 1 } ccaHCCPMemChanSwitchType OBJECT-TYPE SYNTAX INTEGER { others(1), ucWavecom(2), rfSwitchGrp(3), rfSwitchModule(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "Type of the channel switch. others(1) : Any other channel switch which is not in the following list. ucWavecom(2) : Represents the Wavecom upconvertor. rfSwitchGrp(3) : Weinschel channel switch. If ccaHCCPMemChanSwitchModule represents the bitmap of selected modules inside a RF switch chassis. rfSwitchModule(4) : Weinschel channel switch. If ccaHCCPMemChanSwitchModule represents the switch module number inside RF switch chassis." ::= { ccaHCCPMemChanSwitchEntry 2 } ccaHCCPMemChanSwitchIpAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-only STATUS current DESCRIPTION "The type of internet address of ccaHCCPMemChanSwitchIpAddress." ::= { ccaHCCPMemChanSwitchEntry 3 } ccaHCCPMemChanSwitchIpAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The Ipv4 Address of channel switch. It represents the IP address of the upconverter that this Working member connects to if ccaHCCPMemChanSwitchType is ucWavecom(2). It specifies the RF Switch's IP address if ccaHCCPMemChanSwitchType is rfSwitchGrp(3) or rfSwitchModule(4)." ::= { ccaHCCPMemChanSwitchEntry 4 } ccaHCCPMemChanSwitchModule OBJECT-TYPE SYNTAX Integer32(1..255) MAX-ACCESS read-only STATUS current DESCRIPTION "The module number of channel switch for this member . It is the module number on the upconverter that this member connects to if ccaHCCPMemChanSwitchType is ucWavecom(2). It specifies the RF Switch module number inside an RF Switch chassis if ccaHCCPMemChanSwitchType is rfSwitchModule(4). It is the bitmap of selected modules inside a RF Switch chassis if ccaHCCPMemChanSwitchType is rfSwitchGrp(3)." ::= { ccaHCCPMemChanSwitchEntry 5 } ccaHCCPMemChanSwitchProtIpAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-only STATUS current DESCRIPTION "The type of internet address of ccaHCCPMemChanSwitchProtIpAddr." ::= { ccaHCCPMemChanSwitchEntry 6 } ccaHCCPMemChanSwitchProtIpAddr OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The IP address of the Wavecom upconvertor that is connected to the corresponding Protect for this Working member. This object is meaningful only if ccaHCCPMemChanSwitchType is ucWavecom(2) and has no meaning for other types of switches and is ignored in this case." ::= { ccaHCCPMemChanSwitchEntry 7 } ccaHCCPMemChanSwitchProtModule OBJECT-TYPE SYNTAX Integer32(1..255) MAX-ACCESS read-only STATUS current DESCRIPTION "The module number on the Wavecom upconvertor that is connected to the corresponding Protect for this Working member. This object is meaningful only if ccaHCCPMemChanSwitchType is ucWavecom(2)." ::= { ccaHCCPMemChanSwitchEntry 8 } ccaHCCPMemChanSwitchPosition OBJECT-TYPE SYNTAX Integer32(1..8) MAX-ACCESS read-write STATUS current DESCRIPTION "The position within a switch module for this Working member. This object is valid for ccaHCCPMemChanSwitchType rfSwitchGrp(3) and rfSwitchModule(4). " ::= { ccaHCCPMemChanSwitchEntry 9 } ccaHCCPMemChanSwitchSnmpEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to enable SNMP remote control on the Wavecom upconvertor. When it is set to true(1), SNMP remote control is enabled on the upconvertor. When it is set to false(2), SNMP remote control is disabled and front panel manual operation is enabled. This object is meaningful only if ccaHCCPMemChanSwitchType is ucWavecom(2)." ::= { ccaHCCPMemChanSwitchEntry 10 } ccaHCCPOnOffNotificationEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "An indication of whether the ccaHCCPOnNotification and ccaHCCPOffNotification are enabled or disabled." DEFVAL { false } ::= { ccaHCCPObjects 7 } -- -- The Cisco Cable Availability MIB Notifications -- ciscoCableAvailabilityMIBNotificationsPrefix OBJECT IDENTIFIER ::= { ciscoCableAvailabilityMIB 2 } ciscoCableAvailabilityMIBNotifications OBJECT IDENTIFIER ::= { ciscoCableAvailabilityMIBNotificationsPrefix 0 } ccaHCCPOnNotification NOTIFICATION-TYPE OBJECTS { ccaHCCPGroupIfStatus, ccaHCCPGroupIfLastSwitchReason, ccaHCCPMemberState } STATUS current DESCRIPTION "A notification that is sent when failover occurred and this interface is taking over the traffic from the peer. For example if Protect is taking over a Working member from it's protection group,this notification is sent by the Protect. When Working is restored to operation and is now taking over from the Protect, this notification is sent by Working." ::= { ciscoCableAvailabilityMIBNotifications 1 } ccaHCCPOffNotification NOTIFICATION-TYPE OBJECTS { ccaHCCPGroupIfStatus, ccaHCCPGroupIfLastSwitchReason, ccaHCCPMemberState } STATUS current DESCRIPTION "A notification that is sent when failover occurs and this interface is turning over all traffic to it's peer and is now blocking. For example if Protect is taking over a Working member from it's protection group,this notification is sent by the Working. When Working is restored to operation and is now taking over from the Protect, this notification is sent by Protect." ::= { ciscoCableAvailabilityMIBNotifications 2 } ciscoCableAvailabilityMIBConformance OBJECT IDENTIFIER ::= { ciscoCableAvailabilityMIB 3 } ciscoCableAvailabilityMIBCompliances OBJECT IDENTIFIER ::= { ciscoCableAvailabilityMIBConformance 1 } ciscoCableAvailabilityMIBGroups OBJECT IDENTIFIER ::= { ciscoCableAvailabilityMIBConformance 2 } -- compliance statements ciscoCableAvailabilityCompliance MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "The compliance statement for CMTS devices that implement the Hot Standby Connection to Connection Protocol. " MODULE -- this module MANDATORY-GROUPS { ccaHCCPGroup, ccaHCCPMemberGroup, ccaHCCPNotificationGroup } ::= { ciscoCableAvailabilityMIBCompliances 1 } ciscoCableAvailabilityComplianceRev1 MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for CMTS devices that implement the Hot Standby Connection to Connection Protocol. " MODULE -- this module MANDATORY-GROUPS { ccaHCCPGroup, ccaHCCPMemberGroup, ccaHCCPNotificationGroup } OBJECT ccaHCCPMemChanSwitchPosition MIN-ACCESS read-only DESCRIPTION "Write access is not required." ::= { ciscoCableAvailabilityMIBCompliances 2 } -- units of conformance ccaHCCPGroup OBJECT-GROUP OBJECTS { ccaHCCPVersion, ccaHCCPOnOffNotificationEnable, ccaHCCPGroupAuthentication, ccaHCCPGroupAuthKeyChain, ccaHCCPGroupHelloTime, ccaHCCPGroupHoldTime, ccaHCCPGroupRevertEnable, ccaHCCPGroupProtectIpAddrType, ccaHCCPGroupProtectIpAddress, ccaHCCPGroupIfRevertTime, ccaHCCPGroupIfTrackEnable, ccaHCCPGroupIfStatus, ccaHCCPGroupIfLastSwitchReason, ccaHCCPGroupIfOnTransitions, ccaHCCPGroupIfOffTransitions, ccaHCCPGroupTrackIfDescr, ccaHCCPGroupIfState } STATUS current DESCRIPTION "Group of objects implemented in CMTS providing HCCP group information. " ::= { ciscoCableAvailabilityMIBGroups 1 } ccaHCCPMemberGroup OBJECT-GROUP OBJECTS { ccaHCCPMemberIpAddrType, ccaHCCPMemberIpAddress, ccaHCCPMemberState, ccaHCCPMemberSwitchNow, ccaHCCPMemChanSwitchType, ccaHCCPMemChanSwitchIpAddrType, ccaHCCPMemChanSwitchIpAddress, ccaHCCPMemChanSwitchModule, ccaHCCPMemChanSwitchProtIpAddrType, ccaHCCPMemChanSwitchProtIpAddr, ccaHCCPMemChanSwitchProtModule, ccaHCCPMemChanSwitchPosition, ccaHCCPMemChanSwitchSnmpEnable } STATUS current DESCRIPTION "Group of objects implemented in CMTS providing HCCP member and channel switch information." ::= { ciscoCableAvailabilityMIBGroups 2 } ccaHCCPNotificationGroup NOTIFICATION-GROUP NOTIFICATIONS { ccaHCCPOnNotification, ccaHCCPOffNotification } STATUS current DESCRIPTION "The notification which a CISCO-CABLE-AVAILABILITY-MIB entity is required to implement." ::= { ciscoCableAvailabilityMIBGroups 3 } END