-- ***************************************************************** -- Cisco C2900 MIB -- -- September, 1997 Tricia Shueh -- -- Copyright (c) 1996-1999, 2000, 2001, 2002 by cisco Systems, Inc. -- All rights reserved. -- ***************************************************************** -- CISCO-C2900-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE, Counter32, Gauge32, Integer32 FROM SNMPv2-SMI DateAndTime, TruthValue FROM SNMPv2-TC InterfaceIndex FROM IF-MIB ciscoMgmt FROM CISCO-SMI DisplayString, sysName FROM RFC1213-MIB MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP FROM SNMPv2-CONF; ciscoC2900MIB MODULE-IDENTITY LAST-UPDATED "200205300000Z" ORGANIZATION "Cisco Systems, Inc." CONTACT-INFO "Postal: Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA Tel: +1 800 553-NETS E-mail: switchsnmp@cisco.com" DESCRIPTION "The MIB module for Catalyst 2900 enterprise specific information" REVISION "200205300000Z" DESCRIPTION "Added the c2900PortAddrSecureAgingTime, c2900PortAddrSecureAgingType and c2900PortAddrSecureAgingStatic MIB objects to port entry and port group; Also added c2900NotificationsGroup and c2900PortStatsGroupRev1 object." REVISION "200107251345Z" DESCRIPTION "Added the c2900PortVoiceVlanId MIB object to port group." REVISION "9909240000Z" DESCRIPTION "Modified the description for the c2900InfoSelfTestFailed object so that the bits of the self-test bit array are explained." REVISION "9908240000Z" DESCRIPTION "Modified the description for the c2900InfoSelfTestFailed object so that the bits of the self-test bit array are explained." REVISION "9905200000Z" DESCRIPTION "Added enumerated values to c2900ModuleType for: ATM modules VLAN-trunking 10/100 Ethernet modules Gigabit Ethernet module Added one enumerated value to c2900PortAdminSpeed to describe ATM 155.52 Mbps speed." REVISION "9806080000Z" DESCRIPTION "Added the c2900PortSpantreeFast MIB object to port group." REVISION "9804300000Z" DESCRIPTION "Added the c2900PortNoMonitorDestinationPort MIB object to remove a port from the monitored list. Added c2900Portdot1dBasePort to C2900PortEntry. Removed enumerated value securityDynamic(3) from the MIB object c2900PortUsageApplication" ::= { ciscoMgmt 87 } c2900MIBObjects OBJECT IDENTIFIER ::= { ciscoC2900MIB 1 } -- MIB groups c2900SysInfo OBJECT IDENTIFIER ::= { c2900MIBObjects 1 } c2900SysConfig OBJECT IDENTIFIER ::= { c2900MIBObjects 2 } c2900Port OBJECT IDENTIFIER ::= { c2900MIBObjects 4 } c2900BandwidthUsage OBJECT IDENTIFIER ::= { c2900MIBObjects 5 } -- -- General System Information -- c2900InfoBoardRevision OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Returns the revision number of the main board on which the FastSwitch firmware resides." ::= { c2900SysInfo 1 } c2900InfoPeakBuffersUsed OBJECT-TYPE SYNTAX Gauge32 UNITS "buffers" MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of 64-byte buffers used in the main switch buffer pool." ::= { c2900SysInfo 2} c2900InfoTotalBufferDepth OBJECT-TYPE SYNTAX Gauge32 UNITS "buffers" MAX-ACCESS read-only STATUS current DESCRIPTION "It represents the total number of 64-byte buffers in the Ethernet Controller." ::= { c2900SysInfo 3} c2900InfoAddrCapacity OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The system-wide maximum number of MAC addresses supported in the address table, a primary resource when forwarding frames through a bridge. The address table is dynamically updated with new learned addresses inserted and aged addresses removed. The address capacity represented by this object includes dynamic, secure, and static address types. To ensure optimal performance, the number of MAC addresses in the bridged local area network to which this bridge is connected should be less than the value of this object. The system administrator can refer to this object for the number of MAC addresses suppored by this box." ::= { c2900SysInfo 4 } c2900InfoRestrictedStaticAddrCapacity OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The system-wide maximum number of static addresses supported. A static address is one that has explicit source port filtering information assigned. This number limits the static table's entries configured by user." REFERENCE "IEEE 802.1D-1990: Section 6.7.2" ::= { c2900SysInfo 5 } c2900InfoSelfTestFailed OBJECT-TYPE -- -- -- SYNTAX BITS { -- systemBoard(0), -- cpuBuffer(1), -- ram(2), -- helpEngineAsic(3), -- dataBuffer(4), -- bufferTable(5), -- switchEngineAsic(6), -- ethernetFrontEnd(7) -- } SYNTAX OCTET STRING (SIZE (8)) MAX-ACCESS read-only STATUS current DESCRIPTION "A bit array where the presence of a particular bit indicates a failure of a specific Power On Self Test. Bit 0 - System Board Failure Bit 1 - CPU Buffer Failure Bit 2 - Notify RAM Failure Bit 3 - Supervisor ASIC Failure Bit 4 - Data Buffer Failure Bit 5 - Buffer Table Failure Bit 6 - Satellite ASIC Failure Bit 7 - Front End Failure" ::= { c2900SysInfo 6 } c2900InfoUtilDisplay OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of utilization meter LEDs currently lit on the front panel, if the value of c2900InfoVisualIndicatorMode is selected as utilization(4). More LEDs are lit as more total bandwidth through the switch is being utilized. The percentage of the utilization is calculated as follows: the number of LEDs lit/the total number of LEDs. The total number of the LEDs is twenty four for c2900 switch. c2900InfoVisualIndicatorMode is utilization(4). If the value of c2900InfoVisualIndicatorMode is not utilization(4), the value of the object will be zero." ::= { c2900SysInfo 7 } c2900InfoVisualIndicatorMode OBJECT-TYPE SYNTAX INTEGER { portStatus(1), fullDuplex(2), linkRate(3), utilization(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object reflects what is currently selected as the visual indication mode, selected by the mode button. The portStatus(1) mode uses the visual LEDS to indicate port link status. The fullDuplex(2) mode uses the visual LEDS to indicate that a port is running with full duplex or half duplex or no link status. The linkRate(3) mode uses the visual LEDS to indicate the rate of operation on a port: 100 MBPS or 10 MBPS or no link. The utilization(4) mode uses the visual LEDS to indicate the utiliztion of the system as more total bandwidth through the switch is being utilized, more LED's are lit." ::= { c2900SysInfo 8} c2900InfoRedunantPowerSupplyInfo OBJECT-TYPE SYNTAX INTEGER { absent(1), connectedFunctional(2), connectedNotFunctional(3), functionalPrimaryFailed(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "The switch allows a redundant power supply in addition to its local power supply. Only one power source can be supplying power to a unit. absent(1) :the redundant power supply is not connected to the switch. connectedFunctional(2) : the redundant power supply is connected to the switch and operational. connectedNotFunctional(3): the redundant power supply is connected to the switch, but cannot supply power to the system. functionalPrimaryFailed(4): the redundant power supply is installed, powered on, and operational, but a failure exists in the local power supply system." ::= { c2900SysInfo 9 } c2900InfoBoardIdentifier OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Returns the identifier of the main board on which the FastSwitch firmware resides." ::= { c2900SysInfo 10 } -- -- General System Configurations -- c2900ConfigAddressViolationAction OBJECT-TYPE SYNTAX INTEGER { doNothing(1), disablePort(2), sendNotify(3), disablePortAndNotify(4) } MAX-ACCESS read-write STATUS deprecated DESCRIPTION "Indicates what action to take when an address violation (an address mismatch or duplication) occurs on a secure port. The default action is to do nothing. doNothing(1) : do nothing disablePort(2) : disable port; the port can only be reenabled by an explicit management action. sendNotify(3) : generate address violation notification. disablePortAndNotify(4): disable port and send notification. Default value: doNothing(1). This object is deprecated. A separate object c2900PortAddressViolationAction is defined for each port." ::= { c2900SysConfig 1 } c2900ConfigBroadcastStormAlarm OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS deprecated DESCRIPTION "When set to true(1), the switch will generate a broadcastStorm notification upon detecting a port is receiving broadcast packets at a rate higher than or equal to the specified broadcast threshold. When set to false(2), no such trap will be issued. Default value: false(2). This object is deprecated. A separate object c2900PortBroadcastStormAlarm is defined for each port." ::= { c2900SysConfig 2 } -- -- Module Information of c2900 switch. -- c2900ModuleTable OBJECT-TYPE SYNTAX SEQUENCE OF C2900ModuleEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of module entries." ::= { c2900MIBObjects 3 } c2900ModuleEntry OBJECT-TYPE SYNTAX C2900ModuleEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry containing status information about one module in the c2900 chassis." INDEX { c2900ModuleIndex } ::= { c2900ModuleTable 1 } C2900ModuleEntry ::= SEQUENCE { c2900ModuleIndex Integer32, c2900ModuleStatus INTEGER, c2900ModuleType INTEGER, c2900ModuleHwVersion DisplayString, c2900ModuleSwVersion DisplayString } c2900ModuleIndex OBJECT-TYPE SYNTAX Integer32(1..64) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Module index into c2900ModuleTable ." ::= { c2900ModuleEntry 1 } c2900ModuleStatus OBJECT-TYPE SYNTAX INTEGER { moduleNotInstalled(1), moduleInTest(2), moduleHealthy(3), moduleFaulty(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "The overall status of of the module." ::= { c2900ModuleEntry 2 } c2900ModuleType OBJECT-TYPE SYNTAX INTEGER { other(1), -- none of the following empty(2), -- nothing installed -- the following modules are for WS-C2900 wsx2914xl(3), -- 4 port 10/100 TX wsx2922xl(4), -- 2 port 10/100 FX atm155SMLRFiber (5), -- single mode long reach atm155SMMRFiber (6), -- single mode medium reach atm155MMFiber (7), -- multi mode fiber atm155UTP (8), -- unshielded twisted pair wsx2914xlv (9), -- VLAN-trunking 4 port 10/100 TX wsx2922xlv (10), -- VLAN-trunking 2 port 10/100 FX wsx2924xlv (11), -- VLAN-trunking 4 port 10/100 FX wsx2931xl (12), -- 1 port Gigabit Ethernet wsx2932xl (13) -- 1 port Gigabit Ethernet(Copper) } MAX-ACCESS read-only STATUS current DESCRIPTION "The type of module installed in malibu switch." ::= { c2900ModuleEntry 3 } c2900ModuleHwVersion OBJECT-TYPE SYNTAX DisplayString (SIZE (0..12)) MAX-ACCESS read-only STATUS current DESCRIPTION "The hardware version of the module. The format of the version string x.y.z where x,y, and z are hardware register field values." ::= { c2900ModuleEntry 4 } c2900ModuleSwVersion OBJECT-TYPE SYNTAX DisplayString (SIZE (0..40)) MAX-ACCESS read-only STATUS current DESCRIPTION "The software version of the module." ::= { c2900ModuleEntry 5 } -- -- switch Port Table -- c2900PortTable OBJECT-TYPE SYNTAX SEQUENCE OF C2900PortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of port entries. The number of entries is determined by the number of modules in the chassis and the number of ports on each module." ::= { c2900Port 1 } c2900PortEntry OBJECT-TYPE SYNTAX C2900PortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry containing information for a particular switched port on a module installed. The entries are not created or deleted by management commands." INDEX { c2900PortModuleIndex, c2900PortIndex } ::= { c2900PortTable 1 } C2900PortEntry ::= SEQUENCE { c2900PortModuleIndex Integer32, c2900PortIndex Integer32, c2900PortUsageApplication INTEGER, c2900PortGroupIndex Integer32, c2900PortMayLearnAddress TruthValue, -- DEPRECATED OBJECT c2900PortMayForwardFrames TruthValue, c2900PortBufferCongestionControl TruthValue, -- DEPRECATED OBJECT c2900PortBufferCongestionThreshholdPercent Integer32, c2900PortFrameAge Integer32, c2900PortAddrSecureMaxAddresses Integer32, c2900PortAddrSecureCurrentAddresses Gauge32, c2900PortAddrSecureAddrViolations Counter32, c2900PortNumberOfLearnedAddresses Counter32, c2900PortNumberOfDroppedAddresses Counter32, c2900PortClearAddresses TruthValue, c2900PortFloodUnknownMulticasts TruthValue, c2900PortFloodUnknownUnicasts TruthValue, c2900PortLinkbeatStatus INTEGER, c2900PortBroadcastStormAction INTEGER, c2900PortBroadcastRisingThreshold Gauge32, c2900PortBroadcastFallingThreshold Gauge32, c2900PortStatus INTEGER, c2900PortTestResult TruthValue, c2900PortVisualIndicator INTEGER, c2900PortIfIndex InterfaceIndex, c2900PortAddressViolationAction INTEGER, c2900PortBroadcastStormAlarm TruthValue, c2900PortMonitorDestinationPort Integer32, c2900PortSwitchPortIndex Integer32, c2900PortMonitoredPortMap OCTET STRING, c2900PortDuplexState INTEGER, c2900PortDuplexStatus INTEGER, c2900PortAdminSpeed INTEGER, c2900PortNoMonitorDestinationPort Integer32, c2900Portdot1dBasePort Integer32, c2900PortSpantreeFastStart INTEGER, c2900PortVoiceVlanId INTEGER, c2900PortAddrSecureAgingTime Integer32, c2900PortAddrSecureAgingType INTEGER, c2900PortAddrSecureAgingStatic TruthValue } c2900PortModuleIndex OBJECT-TYPE SYNTAX Integer32 (0..64) MAX-ACCESS not-accessible STATUS current DESCRIPTION "An index value that uniquely identifies the module where this port is located. The value is determined by the chassis slot number into which the module is plugged." ::= { c2900PortEntry 1 } c2900PortIndex OBJECT-TYPE SYNTAX Integer32 (1..64) MAX-ACCESS not-accessible STATUS current DESCRIPTION "An index value that uniquely identifies this port within a module." ::= { c2900PortEntry 2 } c2900PortUsageApplication OBJECT-TYPE SYNTAX INTEGER { standard(1), -- standard port usage security(2), -- secured port usage monitor(3), -- monitor usage portGrouping(4), -- fast EtherChannel usage network(5), -- network port usage networkGroup(6), -- network port group usage portGroupDest(7), -- destination addr FEC protected(8) -- protected port usage } MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates how the port is to be used. The variable usage applications are shown above. These applications are defined such that they are mutually exclusive. In other words, a port using the security(2) application cannot also use the monitor(3) application at the same time. The default usage is standard(1), or no special behavior (the port behaves as normal switched port). The security(2) usage adds addressing security to the port, whereby all learned addresses are secure address. The monitor(3) usage provides network diagnosis by reflecting traffic on other ports to this port. The portGrouping(4) application treats this and other ports in the same group as one(inter-switch) connection for more bandwidth potential. When the c2900PortUsageApplication is portGrouping, the c2900PortGroupIndex is set to the index value of the port group. The source address of a received frame is used to determine on which port within the group the frame should be transmitted. The network(5) usage saves address table space when the port is used as the link to a large network with many MAC addresses by disabling address learning on the port and allowing unknown unicasts packets received on other ports of the vlan the port associated with to be forwarded only to the port. The networkGroup(6) usage treates this and other ports in the same group as a network port group. All ports in port are network ports in the sense that address learning is disabled on them and unknown unicast packets received on other ports of the vlan are forwarded to the group. The portGroupDest(7) application treats this and other ports in the same group as one(inter-switch) connection for more bandwidth potential. When the c2900PortUsageApplication is portGroupDest, the c2900PortGroupIndex is set to the index value of the port group. The destination address of a received frame is used to determine on which port within the group the frame should be transmitted. The protected(8) application does not forward any traffic to other protected ports. It does not forward all kinds of unicast, multicast and broadcast traffic to any other protected port. The protected ports, however, forward traffic normally to non-protected ports and vice versa." DEFVAL { standard } ::= { c2900PortEntry 3} c2900PortGroupIndex OBJECT-TYPE SYNTAX Integer32 (1..12) MAX-ACCESS read-write STATUS current DESCRIPTION "This object is meaningful only when the corresponding c2900PortUsageApplication is portGrouping. Ports assigned with the same value of c2900PortGroupIndex belong to the same connection channel." ::= { c2900PortEntry 4} c2900PortMayLearnAddress OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS deprecated DESCRIPTION "This object reflects an internal state of the port with regard to its ability to learn new addresses. Certain port configurations such as learning time limit, security usage, etc., and some Spanning Tree Protocol states can temporarily prohibit the port from learning. This object is true(1) if the port is allowed to learn. It is false(2) otherwise. Setting this object to true(1) will fail, if the port is not in normal state. This object is deprecated." DEFVAL { true } ::= { c2900PortEntry 5} c2900PortMayForwardFrames OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object reflects an internal state of the port with regard to its ability to forward frames. A port sometimes stops forwarding frames when it is blocked by the Spanning Tree Protocol, or while it is undergoing temporary load balancing as part of the port grouping usage. This object is true(1) if the port is allowed to forward frames. It is false(2) otherwise. Setting this object to true(1) will fail, if the port is in the middle of being blocked by the Spanning Tree Protocol, or while it is undergoing temporary load balancing as part of the port grouping usage. This object is only supported for static VLAN access ports." DEFVAL { true } ::= { c2900PortEntry 6} c2900PortBufferCongestionControl OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS deprecated DESCRIPTION "Seting this object to true(1) allows the switch to run its buffer congestion control algorithm on the port. Setting the object to false(2) disallows such control. The buffer congestion control algorithm is summarized in the description of the c2900PortBufferCongestionThresholdPercent below. This object is deprecated" ::= { c2900PortEntry 7} c2900PortBufferCongestionThreshholdPercent OBJECT-TYPE SYNTAX Integer32 (1..99) MAX-ACCESS read-only STATUS current DESCRIPTION "The port buffer congestion threshold provides an early warning to the switch that the port is about to exhaust all its guaranteed buffers, leading to congestion. This threshold is expressed as a percentage of the port's total guaranteed buffer depth. Once this threshold has been crossed, the switch begins colliding with frames received on the port for a fixed period of time. After this time has expired, the switch determines whether the port's buffer congestion has been alleviated. If this situation has not changed, the switch resumes this congestion control algorithm on the port." ::= { c2900PortEntry 8} c2900PortFrameAge OBJECT-TYPE SYNTAX Integer32 (50..4000) UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The aging interval in milliseconds after which old frames queued for transmission on this port are discarded." REFERENCE "Section 4.2 IEEE802.1D-1993" DEFVAL { 1000 } ::= { c2900PortEntry 9} c2900PortAddrSecureMaxAddresses OBJECT-TYPE SYNTAX Integer32 (1..132) MAX-ACCESS read-write STATUS current DESCRIPTION "The maximum number of secure addresses that can be learned on this port when it is a secure port. This number should be always higher than c2900PortAddrSecureCurrentAddresses" ::= { c2900PortEntry 10} c2900PortAddrSecureCurrentAddresses OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The current number of statically assigned unicast addresses on the port." ::= { c2900PortEntry 11} c2900PortAddrSecureAddrViolations OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times a source address was seen on this port which duplicates a secured address configured on another port, plus the number of times a source address was seen on this port which does not match any addresses secured for the port." ::= { c2900PortEntry 12} c2900PortNumberOfLearnedAddresses OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The current number of dynamically learned addresses on the port." ::= { c2900PortEntry 13} c2900PortNumberOfDroppedAddresses OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times an address could not be learned or assigned for the port because its address table was full at one time." ::= { c2900PortEntry 14} c2900PortClearAddresses OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Set to true(1) to delete all learned and assigned dynamic, static and secure unicast addresses the port currently has. Setting the object to false(2) has no effect. This object always returns false(2) when read." ::= { c2900PortEntry 15} c2900PortFloodUnknownMulticasts OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Set to true(1) to allow forwarding to this port frames addressed to multicast addresses that have not been configured for the port. Set to false(2) to filter and discard such frames." DEFVAL { true } ::= { c2900PortEntry 16} c2900PortFloodUnknownUnicasts OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object controls the forwarding of unknown unicast frames to this port. When set to true(1), the switch will, upon receiving a frame with an unknown unicast destination address from another port, transmit the frame to this port. When set to false(2), switch will filter and not transmit said frames to this port. Default value: false(2) for ports using the security or monitor application; true(1) for all other usage applications." ::= { c2900PortEntry 17} c2900PortLinkbeatStatus OBJECT-TYPE SYNTAX INTEGER { unknown(1), linkbeat(2), nolinkbeat(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object depends on the physical layer in use and indicates the current port linkbeat status: if the physical link between two devices is properly connected or not. If the value is linkbeat(1), there is linkbeat. If the value is nolinkbeat(2), there is no linkbeat. If the value is unknown(3), the information is not available." ::= { c2900PortEntry 18} c2900PortBroadcastStormAction OBJECT-TYPE SYNTAX INTEGER { stopBroadcastForwarding(1), forwardBroadcast(2), disablePort(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Indicates what action to take when the broadcast rising threshold for a port is reached. The default action is to forwardBroadcast(2) as usual for all broadcast frames received from the port. The other action is to stopBroadcastForwarding(1) frames until the broadcast reception rate falls to or below the falling threshold. The port can also be shutdown in the event of a broadcast storm with the action disablePort(3)." DEFVAL { forwardBroadcast } ::= { c2900PortEntry 19} c2900PortBroadcastRisingThreshold OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-write STATUS current DESCRIPTION "The broadcast rising threshold is measured in the number of broadcast frames received on a port in a second. When the number of broadcast frames received per second on this port crosses this threshold, the appropriate action as specified by the object c2900PortBroadcastStormAction will take place. See the description of c2900PortBroadcastStormAction." DEFVAL { 500 } ::= { c2900PortEntry 20} c2900PortBroadcastFallingThreshold OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-write STATUS current DESCRIPTION "The broadcast falling threshold is measured in number of broadcast frames received on a port in a second. When the falling threshold is crossed and the c2900PortBroadcastStormAction was stopBroadcastForwarding(1) then broadcast forwarding will be re-enabled on the port. For the other values of c2900PortBroadcastStormAction, crossing the falling threshold has no affect." DEFVAL { 250 } ::= { c2900PortEntry 21} c2900PortStatus OBJECT-TYPE SYNTAX INTEGER { other(1), disabled(2), blocking(3), listening(4), learning(5), preforwarding(6), forwarding(7), secureforwarding(8), suspended(9), broken(10) } MAX-ACCESS read-only STATUS current DESCRIPTION "The port's current state as defined by application of the Spanning Tree Protocol. This state controls what action a port takes on reception of a frame. If the switch has detected a port that is malfunctioning it will place that port into the broken(10) state. For ports which are disabled(see dot1dStpPortEnable), this object will have a value of disabled(2). Since the switch implements three additional states which are not part of IEEE Standard, these additional states are possible values for c2900PortStaus. The additional states are preforwarding(6), secureforwarding(8), and suspended(9). Note: except for these additional states, this object is the same as the dot1dStpPortState object. Default value: blocking(2). This object is only supported for static VLAN access ports." REFERENCE "Section 4.5.5.2 IEEE802.1D-1990" DEFVAL { blocking } ::= {c2900PortEntry 22} c2900PortTestResult OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates if the port passed power on self test or not. If the value of this object is true(1), the port passed test. If the value of this object is false(2), the port failed test." ::= { c2900PortEntry 23 } c2900PortVisualIndicator OBJECT-TYPE SYNTAX INTEGER { notused(1), black(2), amber(3), green(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object is used to indicate the current color of a LED. If a LED is flashing, the value of this object will represent the color of the LED at that instant in time. The following conventions indicate port status: Link healthy returns green(4) Link activity usually green(4), but may return black(2). Link faulty alternating green(4)/amber(3) Port disabled returns amber(3)" ::= { c2900PortEntry 24 } c2900PortIfIndex OBJECT-TYPE SYNTAX InterfaceIndex (1..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "The value of the instance of the ifIndex object, defined in MIB-II, for the interface corresponding to this port." ::= { c2900PortEntry 25 } c2900PortAddressViolationAction OBJECT-TYPE SYNTAX INTEGER { doNothing(1), disablePort(2), sendNotify(3), disablePortAndNotify(4) } MAX-ACCESS read-write STATUS current DESCRIPTION "Indicates what action to take when an address violation (an address mismatch or duplication) occurs on a secure port. The default action is to do nothing. doNothing(1) : do nothing disablePort(2) : disable port; the port can only be reenabled by an explicit management action. sendNotify(3) : generate address violation notification. disablePortAndNotify(4): disable port and send notification." DEFVAL { doNothing } ::= { c2900PortEntry 26 } c2900PortBroadcastStormAlarm OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "When set to true(1), the switch will generate a broadcastStorm notification upon detecting a port is receiving broadcast packets at a rate higher than or equal to the threshold specified by c2900PortBroadcastRisingThreshold. When set to false(2), no such trap will be issued. Default value: false(2). c2900PortBroadcastStormAlarm is defined for each port." DEFVAL { false } ::= { c2900PortEntry 27 } c2900PortMonitorDestinationPort OBJECT-TYPE SYNTAX Integer32 (0..64) MAX-ACCESS read-write STATUS current DESCRIPTION "Switch Port (c2900PortSwitchPortIndex) index value of the port that is to be monitored by this port. A value of zero can't be used to do set, it is used to return when this object is read. To remove a port from the monitored list use the object c2900PortNoMonitorDestinationPort." ::= { c2900PortEntry 28 } c2900PortSwitchPortIndex OBJECT-TYPE SYNTAX Integer32 (1..64) MAX-ACCESS read-only STATUS current DESCRIPTION "Switch port index of a port is a value that uniquely identifies the port within a switch. This is obtained from the port index (c2900PortIndex) and the module index (c2900PortModuleIndex)." ::= { c2900PortEntry 29 } c2900PortMonitoredPortMap OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates which ports are actually being monitored. The octet string contains one bit per port. Each bit within the octet string represents one port of the device. The ordering of ports represented within the octet string is in the same order as in the RFC 1493 dot1dStaticAllowedToGoTo in the dot1dStaticTable. The bit value interpretation is as follows: 1 = being monitored 0 = not being monitored" ::= { c2900PortEntry 30 } c2900PortDuplexState OBJECT-TYPE SYNTAX INTEGER { fullduplex(1), halfduplex(2), autoNegotiate(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Set to fullduplex(1) to operate in full duplex mode, port will allow simultaneous transmit and receive which can double its bandwidth. Set to halfduplex(2) to operate in half duplex mode. Set to autoNegotiate(3) to allow the switch to negoti- ate with the other end of the connection. The status of duplex mode on a port is available with c2900PortDuplexStatus object." DEFVAL { autoNegotiate } ::= { c2900PortEntry 31 } c2900PortDuplexStatus OBJECT-TYPE SYNTAX INTEGER { fullduplex(1), halfduplex(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The status of duplex mode on this port. When linkbeat is not present, halfduplex is always reported. When linkbeat is present, the result of full duplex auto-negotiation is reported if c2900PortDuplexState is set to auto-negotiate, otherwise it reports fullduplex if c2900PortDuplexState is set to fullduplex or halfduplex if c2900PortDuplexState is set to halfduplex." ::= { c2900PortEntry 32 } c2900PortAdminSpeed OBJECT-TYPE SYNTAX INTEGER { autoDetect(1), s10000000(10000000), -- 10 Mbps s100000000(100000000), -- 100 Mbps s155520000(155520000) -- ATM 155.52 Mbps } MAX-ACCESS read-write STATUS current DESCRIPTION "The object controls the speed of the port. The current operational speed of the port can be determined from ifSpeed." DEFVAL { autoDetect } ::= { c2900PortEntry 33 } c2900PortNoMonitorDestinationPort OBJECT-TYPE SYNTAX Integer32 (0..64) MAX-ACCESS read-write STATUS current DESCRIPTION "Switch Port (c2900PortSwitchPortIndex) index value of the port that is to be removed from the monitored list. A value of zero can't be used to do set, it is used to return when this object is read. To add a port to the monitored list use the object c2900PortMonitorDestinationPort." ::= { c2900PortEntry 34 } c2900Portdot1dBasePort OBJECT-TYPE SYNTAX Integer32 (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "This is the dot1dBasePort associated with this port." ::= { c2900PortEntry 35} c2900PortSpantreeFastStart OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Indicates whether the port is operating in spantree fast start mode. A port with fast start enabled is immediately put in spanning tree forwarding state on link up, rather than starting in blocking state which is the normal operation. This is useful when the port is known to be connected to a single station which has problems waiting for the normal spanning tree operation to put the port in forwarding state." DEFVAL { disabled } ::= { c2900PortEntry 36 } c2900PortVoiceVlanId OBJECT-TYPE SYNTAX INTEGER ( 0|1..1000|4095|4096 ) MAX-ACCESS read-write STATUS current DESCRIPTION "The Voice Virtual Vlan ID (VVID) to which this port belongs to. If the VVID is not supported on the port, this MIB object will not be configurable and will return 4096. Setting this MIB object to 4096, the CDP packets transmitting through this port would not include Appliance VLAN-ID TLV. Setting this MIB object to 4095, the CDP packets transmitting through this port would contain Appliance VLAN-ID TLV with value of 4095 - VoIP and related packets are expected to be sent and received untagged without an 802.1p priority. Setting this MIB object to 0, the CDP packets transmitting through this port would contain Appliance VLAN-ID TLV with value of 0 - VoIP and related packets are expected to be sent and received with VLAN-id=0 and an 802.1p priority. Setting this MIB object to N (1..1000), the CDP packets transmitting through this port would contain Appliance VLAN-ID TLV with N - VoIP and related packets are expected to be sent and received with VLAN-id=N and an 802.1p priority." ::= { c2900PortEntry 37 } c2900PortAddrSecureAgingTime OBJECT-TYPE SYNTAX Integer32 (0..1440) UNITS "minutes" MAX-ACCESS read-write STATUS current DESCRIPTION "The aging interval in minutes for each secure address entry on a given port. Depending on the type of aging the secure address will age out after the expiration of the aging time and will be removed from the secure address list. Any change in the value of this object will restart the aging for all the secure addresses on this port. If the value of this object is 0 for a given port, the aging mechanism is disabled for this port." DEFVAL { 0 } ::= { c2900PortEntry 38 } c2900PortAddrSecureAgingType OBJECT-TYPE SYNTAX INTEGER { absolute(1), inactivity(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "If the value of this object on a given port is absolute - all the secure addresses on this port will age out exactly after the aging time configured for this port. inactivity - the secure addresses on this port will age out only if there is no data traffic from the given secure source address for a time period specified by aging time. Any change in the value of this object will restart the aging for all the secure addresses on this port. The value of this object is not effective when the value of c2900PortAddrSecureAgingTime is 0." DEFVAL { absolute } ::= { c2900PortEntry 39 } c2900PortAddrSecureAgingStatic OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Set to true(1) to enable aging for statically configured secure addresses on one port. Disable the aging for statically configured secure addresses if set to false(2). Any change in the value of this object will restart the aging for all the configured secure addresses on this port. The value of this object is not effective when the value of c2900PortAddrSecureAgingTime is 0." DEFVAL { false } ::= { c2900PortEntry 40 } -- -- The switch Port Statistics Table -- c2900PortStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF C2900PortStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of port entries. The number of entries is determined by the number of modules in the chassis and the number of ports on each module." ::= { c2900Port 2 } c2900PortStatsEntry OBJECT-TYPE SYNTAX C2900PortStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry containing information for a particular switched port on a module installed. The entry cannot be created or deleted." INDEX { c2900PortModuleIndex, c2900PortIndex } ::= { c2900PortStatsTable 1 } C2900PortStatsEntry ::= SEQUENCE { c2900PortRxNoBwFrames Counter32, c2900PortRxNoBufferFrames Counter32, c2900PortRxNoDestUniFrames Counter32, c2900PortRxNoDestMultiFrames Counter32, c2900PortRxSuppressBcastFrames Counter32, -- DEPRECATED OBJECT c2900PortRxFcsErrFrames Counter32, c2900PortCollFragFrames Counter32, c2900PortTxMulticastFrames Counter32, c2900PortTxBroadcastFrames Counter32 } c2900PortRxNoBwFrames OBJECT-TYPE SYNTAX Counter32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "A count of frames received on this port that were discarded due to a lack of bandwidth resources in the Catalyst Switch forwarding engine." ::= { c2900PortStatsEntry 1 } c2900PortRxNoBufferFrames OBJECT-TYPE SYNTAX Counter32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "A count of frames received that were discarded due to a lack of frame buffer resources in the Catalyst Switch forwarding engine." ::= { c2900PortStatsEntry 2 } c2900PortRxNoDestUniFrames OBJECT-TYPE SYNTAX Counter32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "A count of unicast frames received that were discarded, because the forwarding rules stipulate that they are not be forwarded." ::= { c2900PortStatsEntry 3 } c2900PortRxNoDestMultiFrames OBJECT-TYPE SYNTAX Counter32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "A count of multicast frames received that were discarded, because they have not been configured for the port." ::= { c2900PortStatsEntry 4 } c2900PortRxSuppressBcastFrames OBJECT-TYPE SYNTAX Counter32 UNITS "frames" MAX-ACCESS read-only STATUS deprecated DESCRIPTION "A count of broadcast frames received that were discarded because of the threshold-based broadcast suppression. This object is deprecated, because there is no way that the Malibu system to give the brodcast_supress frames" ::= { c2900PortStatsEntry 5 } c2900PortRxFcsErrFrames OBJECT-TYPE SYNTAX Counter32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of frames received with FCS errors. This total includes all frames received with an FCS error and an integral number of bytes. Unlike RFC1650's dot3StatsFCSErrors, this object does not include frames which are less than the minimum packet size (such as collision fragments)." ::= { c2900PortStatsEntry 6 } c2900PortCollFragFrames OBJECT-TYPE SYNTAX Counter32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of frames whose lengths are less than 64 and have bad FCS values. The preamble and sfd fields are excluded from the byte count of a frame while the FCS field is included." ::= { c2900PortStatsEntry 7 } c2900PortTxMulticastFrames OBJECT-TYPE SYNTAX Counter32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "A count of frames that are successfully transmitted and are directed to a multicast address. Unlike RFC1573's ifOutMulticastPkts, this object does not include those that were discarded or not sent." ::= { c2900PortStatsEntry 8 } c2900PortTxBroadcastFrames OBJECT-TYPE SYNTAX Counter32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "A count of frames that are successfully transmitted and are directed to the broadcast address. Unlike RFC1573's ifOutBroadcastPkts, this object does not include those that were discarded or not sent." ::= { c2900PortStatsEntry 9 } -- -- Bandwidth Usage Information -- c2900BandwidthUsageCurrent OBJECT-TYPE SYNTAX Gauge32 UNITS "megabits per second" MAX-ACCESS read-only STATUS current DESCRIPTION "The current bandwidth consumed. The measurement unit is in megabits per second (1,000,000 bits/second). This value gives a reasonable estimate of the amount of traffic currently flowing through the switch. It is calculated as follows: Octets*8 + Frames*(96 + 64) --------------------------- Measurement Interval * 1,000,000 * 2 Where: Measurement Interval is the amount of time over which the Octets and Frames were collected, in seconds. Measurement Interval is always one second in current implementation. Octets is the total number of octets transmitted or received by all network interfaces, excluding framing data but including FCS. This includes octets in frames which were partially transmitted or received (due to collisions, for example). Frames is the total number of frames transmitted or received by all network interfaces, including frames with errors. The number of frames is multiplied by 96 plus 64 in order to estimate the delay between each frame for Ethernet's IPG and preamble/SFD. The '2' in the divisor makes this a forwarding bandwidth counter. A frame received on one interface is typically forwarded out another interface. In order to avoid double- counting this frame's bandwidth, once on the receiving interface and once on the transmitting interface, the total bandwidth is divided by two. Since multicast and broadcast frames can be sent to multiple ports, the above is at best a lower bound." ::= { c2900BandwidthUsage 1 } c2900BandwidthUsageMaxPeakEntries OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of entries c2900BandwidthUsagePeakTable can have." ::= { c2900BandwidthUsage 2 } c2900BandwidthUsagePeakInterval OBJECT-TYPE SYNTAX INTEGER { onehour(1),threehours(3),sixhours(6), twelvehours(12),oneday(24),twodays(48), threedays(72),fourdays(96),fivedays(120), sixdays(144),oneweek(168) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the length of time which forms a peak bandwidth measurement interval. A write to this object with any new value restarts the peak bandwidth recording interval used by bandwidthUsagePeakTable. In other words, the bandwidthUsagePeakTable will be cleared and entry number one will record the peak with a new measurement interval." DEFVAL { oneday } ::= { c2900BandwidthUsage 3 } c2900BandwidthUsagePeakRestart OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Set to true(1) to clear the c2900BandwidthUsagePeakTable and restart the peak bandwidth recording. No action will be taken if this object is set to false(2). This object returns false(2) when read." ::= { c2900BandwidthUsage 4 } c2900BandwidthUsageCurrentPeakEntry OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "A value identifying an instance of the c2900BandwidthUsagePeakIndex where the peak bandwidth estimation is most recent." ::= { c2900BandwidthUsage 5 } c2900BandwidthUsagePeakTable OBJECT-TYPE SYNTAX SEQUENCE OF C2900BandwidthUsagePeakEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of entries containing peak bandwidth usages in a number of recording interval. After being cleared, entries are added to the bandwidthUsagePeakTable with ascending values of c2900BandwidthUsagePeakIndex starting at 1. When the number of entries reaches c2900BandwidthUsageMaxPeakEntries, each new recording interval is assigned the value of c2900BandwidthUsagePeakIndex corresponding to the oldest entry, overwriting the previous contents of that entry." ::= { c2900BandwidthUsage 6 } c2900BandwidthUsagePeakEntry OBJECT-TYPE SYNTAX C2900BandwidthUsagePeakEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about peak bandwidth usage in a recording interval." INDEX { c2900BandwidthUsagePeakIndex } ::= { c2900BandwidthUsagePeakTable 1 } C2900BandwidthUsagePeakEntry ::= SEQUENCE { c2900BandwidthUsagePeakIndex Integer32, c2900BandwidthUsageStartTime DateAndTime, c2900BandwidthUsagePeak Gauge32, c2900BandwidthUsagePeakTime DateAndTime } c2900BandwidthUsagePeakIndex OBJECT-TYPE SYNTAX Integer32 (1..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "Number from one to c2900BandwidthUsageMaxPeakEntries identifying a particular c2900BandwithUsagePeakEntry." ::= { c2900BandwidthUsagePeakEntry 1 } c2900BandwidthUsageStartTime OBJECT-TYPE SYNTAX DateAndTime MAX-ACCESS read-only STATUS current DESCRIPTION "The time that marks the start of this recording interval." ::= { c2900BandwidthUsagePeakEntry 2 } c2900BandwidthUsagePeak OBJECT-TYPE SYNTAX Gauge32 UNITS "megabits per second" MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum bandwidth usage of any measurement interval within this recording interval. This value is an estimate of the highest amount of traffic flowing through the switch during this recording interval. It is calculated as follows: Octets*8 + Frames*(96 + 64) --------------------------- Measurement Interval * 1,000,000 * 2 Where: Measurement Interval is the amount of time over which the Octets and Frames were collected, in seconds. Measurement Interval is always one second in c2900's implementation. Octets is the total number of octets transmitted or received by all network interfaces, excluding framing data but including FCS. This includes octets in frames which were partially transmitted or received (due to collisions, for example). Frames is the total number of frames transmitted or received by all network interfaces, including frames with errors. The number of frames is multiplied by 96 plus 64 in order to estimate the delay between each frame for Ethernet's IPG and preamble/SFD. The '2' in the divisor makes this a forwarding bandwidth counter. A frame received on one interface is typically forwarded out another interface. In order to avoid double- counting this frame's bandwidth, once on the receiving interface and once on the transmitting interface, the total bandwidth is divided by two. Since multicast and broadcast frames can be sent to multiple ports, the above is at best a lower bound." ::= { c2900BandwidthUsagePeakEntry 3 } c2900BandwidthUsagePeakTime OBJECT-TYPE SYNTAX DateAndTime MAX-ACCESS read-only STATUS current DESCRIPTION "The start time of the measurement interval." ::= { c2900BandwidthUsagePeakEntry 4 } -- -- C a t a l y s t N O T I F I C A T I O N S -- c2900MibNotifications OBJECT IDENTIFIER ::= { ciscoC2900MIB 2 } c2900MibNotificationsPrefix OBJECT IDENTIFIER ::= { c2900MibNotifications 0 } c2900AddressViolation NOTIFICATION-TYPE OBJECTS {c2900PortIfIndex} STATUS current DESCRIPTION "The addressViolation notification is generated when an address violation is detected on a secured port. The generation of the addressViolation notification can be enabled or suppressed using the object c2900ConfigAddressViolationAction. The particular secured port is indicated by the value of c2900PortIfIndex." ::= { c2900MibNotificationsPrefix 1 } c2900BroadcastStorm NOTIFICATION-TYPE OBJECTS {c2900PortBroadcastRisingThreshold} STATUS current DESCRIPTION "The broadcastStorm notification is generated upon detecting a port is receiving broadcast packets at a rate crossing the specified broadcast threshold. This trap is only for the rising threshold. The particular port is indicated by the values of c2900PortModuleIndex and c2900PortIndex, and the value of the threshold is given by c2900PortBroadcastRisingThreshold." ::= { c2900MibNotificationsPrefix 2 } c2900RpsFailed NOTIFICATION-TYPE OBJECTS {sysName} STATUS current DESCRIPTION "A redundant power system (RPS) is connected to the switch. The RpsFailed notification is generated upon detecting RPS failure." ::= { c2900MibNotificationsPrefix 3 } -- -- C o n f o r m a n c e -- -- conformance information c2900MIBConformance OBJECT IDENTIFIER ::= { ciscoC2900MIB 3 } c2900MIBCompliances OBJECT IDENTIFIER ::= { c2900MIBConformance 1 } c2900MIBGroups OBJECT IDENTIFIER ::= { c2900MIBConformance 2 } -- compliance statements c2900MIBCompliance MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "The compliance statement for all c2900 switch." MODULE -- this module MANDATORY-GROUPS { c2900SysInfoGroup, c2900SysConfigGroup, c2900PortGroup, c2900BandwidthUsageGroup } ::= { c2900MIBCompliances 1 } c2900MIBComplianceSA3 MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "The compliance statement for all c2900 switch." MODULE -- this module MANDATORY-GROUPS { c2900SysInfoGroup, c2900ModuleGroup, c2900BandwidthUsageGroup, c2900PortGroupSA3, c2900PortStatsGroupSA3 } ::= { c2900MIBCompliances 3 } c2900MIBComplianceSA5 MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "The compliance statement for all c2900 switch." MODULE -- this module MANDATORY-GROUPS { c2900SysInfoGroup, c2900ModuleGroup, c2900BandwidthUsageGroup, c2900PortGroupSA5 } ::= { c2900MIBCompliances 2 } c2900MIBComplianceSA7 MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "The compliance statement for all c2900 switch." MODULE -- this module MANDATORY-GROUPS { c2900SysInfoGroup, c2900ModuleGroup, c2900BandwidthUsageGroup, c2900PortGroupSA7 } ::= { c2900MIBCompliances 4 } c2900MIBComplianceWC2 MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "The compliance statement for all c2900 switch." MODULE -- this module MANDATORY-GROUPS { c2900SysInfoGroup, c2900ModuleGroup, c2900BandwidthUsageGroup, c2900PortGroupWC2 } ::= { c2900MIBCompliances 5 } c2900MIBComplianceWC4 MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for all c2900 switch." MODULE -- this module MANDATORY-GROUPS { c2900SysInfoGroup, c2900ModuleGroup, c2900BandwidthUsageGroup, c2900PortGroupWC4, c2900NotificationsGroup } GROUP c2900PortStatsGroupRev1 DESCRIPTION "This group is optional." ::= { c2900MIBCompliances 6 } -- Units of Conformance c2900SysInfoGroup OBJECT-GROUP OBJECTS { c2900InfoBoardRevision, c2900InfoPeakBuffersUsed, c2900InfoTotalBufferDepth, c2900InfoAddrCapacity, c2900InfoRestrictedStaticAddrCapacity, c2900InfoSelfTestFailed, c2900InfoUtilDisplay, c2900InfoVisualIndicatorMode, c2900InfoRedunantPowerSupplyInfo, c2900InfoBoardIdentifier } STATUS current DESCRIPTION "The collection of objects which are used to provide the general switch information." ::= { c2900MIBGroups 1 } c2900SysConfigGroup OBJECT-GROUP OBJECTS { c2900ConfigAddressViolationAction, -- DEPRECATED OBJECT c2900ConfigBroadcastStormAlarm -- DEPRECATED OBJECT } STATUS deprecated DESCRIPTION "The collection of objects which are used to configure the switch." ::= { c2900MIBGroups 2 } c2900ModuleGroup OBJECT-GROUP OBJECTS { c2900ModuleStatus, c2900ModuleType, c2900ModuleHwVersion, c2900ModuleSwVersion } STATUS current DESCRIPTION "The object is used to provide the module status." ::= { c2900MIBGroups 3 } c2900PortGroup OBJECT-GROUP OBJECTS { c2900PortUsageApplication, c2900PortGroupIndex, c2900PortMayLearnAddress, -- DEPRECATED OBJECT c2900PortMayForwardFrames, c2900PortBufferCongestionControl, -- DEPRECATED OBJECT c2900PortBufferCongestionThreshholdPercent, c2900PortFrameAge, c2900PortAddrSecureMaxAddresses, c2900PortAddrSecureCurrentAddresses, c2900PortAddrSecureAddrViolations, c2900PortNumberOfLearnedAddresses, c2900PortNumberOfDroppedAddresses, c2900PortClearAddresses, c2900PortFloodUnknownMulticasts, c2900PortFloodUnknownUnicasts, c2900PortLinkbeatStatus, c2900PortBroadcastStormAction, c2900PortBroadcastRisingThreshold, c2900PortBroadcastFallingThreshold, c2900PortStatus, c2900PortTestResult, c2900PortVisualIndicator, c2900PortIfIndex, c2900PortAddressViolationAction, c2900PortBroadcastStormAlarm, c2900PortMonitorDestinationPort, c2900PortSwitchPortIndex, c2900PortMonitoredPortMap, c2900PortDuplexState, c2900PortDuplexStatus, c2900PortAdminSpeed, c2900PortNoMonitorDestinationPort } STATUS deprecated DESCRIPTION "The collection of objects which are used to provide port status and configuration." ::= { c2900MIBGroups 4 } c2900PortStatsGroup OBJECT-GROUP OBJECTS { c2900PortRxNoBwFrames, c2900PortRxNoBufferFrames, c2900PortRxNoDestUniFrames, c2900PortRxNoDestMultiFrames, c2900PortRxSuppressBcastFrames, -- DEPRECATED OBJECT c2900PortRxFcsErrFrames, c2900PortCollFragFrames, c2900PortTxMulticastFrames, c2900PortTxBroadcastFrames } STATUS deprecated DESCRIPTION "The collection of objects which are used to provide port stats." ::= { c2900MIBGroups 5 } c2900BandwidthUsageGroup OBJECT-GROUP OBJECTS { c2900BandwidthUsageCurrent, c2900BandwidthUsageMaxPeakEntries, c2900BandwidthUsagePeakInterval, c2900BandwidthUsagePeakRestart, c2900BandwidthUsagePeakIndex, c2900BandwidthUsageStartTime, c2900BandwidthUsagePeak, c2900BandwidthUsagePeakTime, c2900BandwidthUsageCurrentPeakEntry } STATUS current DESCRIPTION "The collection of objects which are used to provide the bandwidth information." ::= { c2900MIBGroups 6 } c2900PortGroupSA3 OBJECT-GROUP OBJECTS { c2900PortUsageApplication, c2900PortGroupIndex, c2900PortMayLearnAddress, c2900PortMayForwardFrames, c2900PortBufferCongestionThreshholdPercent, c2900PortFrameAge, c2900PortAddrSecureMaxAddresses, c2900PortAddrSecureCurrentAddresses, c2900PortAddrSecureAddrViolations, c2900PortNumberOfLearnedAddresses, c2900PortNumberOfDroppedAddresses, c2900PortClearAddresses, c2900PortFloodUnknownMulticasts, c2900PortFloodUnknownUnicasts, c2900PortLinkbeatStatus, c2900PortBroadcastStormAction, c2900PortBroadcastRisingThreshold, c2900PortBroadcastFallingThreshold, c2900PortStatus, c2900PortTestResult, c2900PortVisualIndicator, c2900PortIfIndex, c2900PortAddressViolationAction, c2900PortBroadcastStormAlarm, c2900PortMonitorDestinationPort, c2900PortSwitchPortIndex, c2900PortMonitoredPortMap, c2900PortDuplexState, c2900PortDuplexStatus, c2900PortAdminSpeed, c2900PortNoMonitorDestinationPort } STATUS deprecated DESCRIPTION "The collection of objects which are used to provide port status and configuration." ::= { c2900MIBGroups 7 } c2900PortStatsGroupSA3 OBJECT-GROUP OBJECTS { c2900PortRxNoBwFrames, c2900PortRxNoBufferFrames, c2900PortRxNoDestUniFrames, c2900PortRxNoDestMultiFrames, c2900PortRxFcsErrFrames, c2900PortCollFragFrames, c2900PortTxMulticastFrames, c2900PortTxBroadcastFrames } STATUS deprecated DESCRIPTION "The collection of objects which are used to provide port stats." ::= { c2900MIBGroups 8 } c2900PortGroupSA5 OBJECT-GROUP OBJECTS { c2900PortUsageApplication, c2900PortGroupIndex, c2900PortMayForwardFrames, c2900PortBufferCongestionThreshholdPercent, c2900PortFrameAge, c2900PortAddrSecureMaxAddresses, c2900PortAddrSecureCurrentAddresses, c2900PortAddrSecureAddrViolations, c2900PortNumberOfLearnedAddresses, c2900PortNumberOfDroppedAddresses, c2900PortClearAddresses, c2900PortFloodUnknownMulticasts, c2900PortFloodUnknownUnicasts, c2900PortLinkbeatStatus, c2900PortBroadcastStormAction, c2900PortBroadcastRisingThreshold, c2900PortBroadcastFallingThreshold, c2900PortStatus, c2900PortTestResult, c2900PortVisualIndicator, c2900PortIfIndex, c2900PortAddressViolationAction, c2900PortBroadcastStormAlarm, c2900PortMonitorDestinationPort, c2900PortSwitchPortIndex, c2900PortMonitoredPortMap, c2900PortDuplexState, c2900PortDuplexStatus, c2900PortAdminSpeed, c2900PortNoMonitorDestinationPort, c2900Portdot1dBasePort } STATUS deprecated DESCRIPTION "The collection of objects which are used to provide port status and configuration." ::= { c2900MIBGroups 9 } c2900PortGroupSA7 OBJECT-GROUP OBJECTS { c2900PortUsageApplication, c2900PortGroupIndex, c2900PortMayForwardFrames, c2900PortBufferCongestionThreshholdPercent, c2900PortFrameAge, c2900PortAddrSecureMaxAddresses, c2900PortAddrSecureCurrentAddresses, c2900PortAddrSecureAddrViolations, c2900PortNumberOfLearnedAddresses, c2900PortNumberOfDroppedAddresses, c2900PortClearAddresses, c2900PortFloodUnknownMulticasts, c2900PortFloodUnknownUnicasts, c2900PortLinkbeatStatus, c2900PortBroadcastStormAction, c2900PortBroadcastRisingThreshold, c2900PortBroadcastFallingThreshold, c2900PortStatus, c2900PortTestResult, c2900PortVisualIndicator, c2900PortIfIndex, c2900PortAddressViolationAction, c2900PortBroadcastStormAlarm, c2900PortMonitorDestinationPort, c2900PortSwitchPortIndex, c2900PortMonitoredPortMap, c2900PortDuplexState, c2900PortDuplexStatus, c2900PortAdminSpeed, c2900PortNoMonitorDestinationPort, c2900Portdot1dBasePort, c2900PortSpantreeFastStart } STATUS deprecated DESCRIPTION "The collection of objects which are used to provide port status and configuration." ::= { c2900MIBGroups 10 } c2900PortGroupWC2 OBJECT-GROUP OBJECTS { c2900PortUsageApplication, c2900PortGroupIndex, c2900PortMayForwardFrames, c2900PortBufferCongestionThreshholdPercent, c2900PortFrameAge, c2900PortAddrSecureMaxAddresses, c2900PortAddrSecureCurrentAddresses, c2900PortAddrSecureAddrViolations, c2900PortNumberOfLearnedAddresses, c2900PortNumberOfDroppedAddresses, c2900PortClearAddresses, c2900PortFloodUnknownMulticasts, c2900PortFloodUnknownUnicasts, c2900PortLinkbeatStatus, c2900PortBroadcastStormAction, c2900PortBroadcastRisingThreshold, c2900PortBroadcastFallingThreshold, c2900PortStatus, c2900PortTestResult, c2900PortVisualIndicator, c2900PortIfIndex, c2900PortAddressViolationAction, c2900PortBroadcastStormAlarm, c2900PortMonitorDestinationPort, c2900PortSwitchPortIndex, c2900PortMonitoredPortMap, c2900PortDuplexState, c2900PortDuplexStatus, c2900PortAdminSpeed, c2900PortNoMonitorDestinationPort, c2900Portdot1dBasePort, c2900PortSpantreeFastStart, c2900PortVoiceVlanId } STATUS deprecated DESCRIPTION "The collection of objects which are used to provide port status and configuration, includes voice vlan id." ::= { c2900MIBGroups 11 } c2900PortGroupWC4 OBJECT-GROUP OBJECTS { c2900PortUsageApplication, c2900PortGroupIndex, c2900PortMayForwardFrames, c2900PortBufferCongestionThreshholdPercent, c2900PortFrameAge, c2900PortAddrSecureMaxAddresses, c2900PortAddrSecureCurrentAddresses, c2900PortAddrSecureAddrViolations, c2900PortNumberOfLearnedAddresses, c2900PortNumberOfDroppedAddresses, c2900PortClearAddresses, c2900PortFloodUnknownMulticasts, c2900PortFloodUnknownUnicasts, c2900PortLinkbeatStatus, c2900PortBroadcastStormAction, c2900PortBroadcastRisingThreshold, c2900PortBroadcastFallingThreshold, c2900PortStatus, c2900PortTestResult, c2900PortVisualIndicator, c2900PortIfIndex, c2900PortAddressViolationAction, c2900PortBroadcastStormAlarm, c2900PortMonitorDestinationPort, c2900PortSwitchPortIndex, c2900PortMonitoredPortMap, c2900PortDuplexState, c2900PortDuplexStatus, c2900PortAdminSpeed, c2900PortNoMonitorDestinationPort, c2900Portdot1dBasePort, c2900PortSpantreeFastStart, c2900PortVoiceVlanId, c2900PortAddrSecureAgingTime, c2900PortAddrSecureAgingType, c2900PortAddrSecureAgingStatic } STATUS current DESCRIPTION "The collection of objects which are used to provide port status and configuration, includes voice vlan id and port-security aging." ::= { c2900MIBGroups 12 } c2900NotificationsGroup NOTIFICATION-GROUP NOTIFICATIONS { c2900AddressViolation, c2900BroadcastStorm, c2900RpsFailed } STATUS current DESCRIPTION "The set of notifications provided by c2900 device." ::= { c2900MIBGroups 13 } c2900PortStatsGroupRev1 OBJECT-GROUP OBJECTS { c2900PortRxNoBwFrames, c2900PortRxNoBufferFrames, c2900PortRxNoDestUniFrames, c2900PortRxNoDestMultiFrames, c2900PortRxFcsErrFrames, c2900PortCollFragFrames, c2900PortTxMulticastFrames, c2900PortTxBroadcastFrames } STATUS current DESCRIPTION "The collection of objects which are used to provide port stats." ::= { c2900MIBGroups 14 } END