-- ***************************************************************** -- CISCO-BULK-FILE-MIB.my: Bulk file creation MIB -- -- August 1997, Bob Stewart -- June 2001, Thai Dang -- August 2001, A S Kiran Koushik -- April 2002, David L. Battle -- Jun 2002, Kapil Kataria -- -- Copyright (c) 1997, 1998, 2001, 2002 by cisco Systems, Inc. -- All rights reserved. -- -- ***************************************************************** CISCO-BULK-FILE-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE, zeroDotZero, Counter32, Gauge32, Unsigned32 FROM SNMPv2-SMI RowStatus, DisplayString, TruthValue, TimeStamp FROM SNMPv2-TC MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP FROM SNMPv2-CONF ciscoMgmt FROM CISCO-SMI; ciscoBulkFileMIB MODULE-IDENTITY LAST-UPDATED "200206100000Z" ORGANIZATION "Cisco Systems, Inc." CONTACT-INFO "Cisco Systems Customer Service Postal: 170 W Tasman Drive San Jose, CA 95134 USA Tel: +1 800 553-NETS E-mail: cs-snmp@cisco.com" DESCRIPTION "The MIB module for creating and deleting bulk files of SNMP data for file transfer." REVISION "200206100000Z" DESCRIPTION "Added enum 'forcedCreate' for object 'cbfDefineFileNow' for forced creation of configuration files." REVISION "200205150000Z" DESCRIPTION "Added default values for all read-write objects in table to simplify creation of table rows." REVISION "200108220000Z" DESCRIPTION "Modified description of objects cbfDefineObjectTableInstance and cbfDefineObjectLastPolledInst in cbfDefineObjectTable to accept/represent Full OIDs instead of partial OIDs." REVISION "200108010000Z" DESCRIPTION "Enhanced the MIB for selective row transfer from MIBS. Added a notification to indicate bulk file creation or error(during creation of the file). Added object cbfDefineFileNotifyOnCompletion to cbfDefineFileTable. Added the objects cbfDefineObjectTableInstance, cbfDefineObjectLastPolledInst and cbfDefineObjectNumEntries to cbfDefineObjectTable. Added cbfDefineFileCompletion notification." REVISION "200106261700Z" DESCRIPTION "Added the following enumerations variantBERWithCksum(4) and variantBinWithCksum(5) in cbfDefineFileFormat" REVISION "9810291700Z" DESCRIPTION "Initial version of this MIB module." ::= { ciscoMgmt 81 } ciscoBulkFileMIBObjects OBJECT IDENTIFIER ::= { ciscoBulkFileMIB 1 } cbfDefine OBJECT IDENTIFIER ::= { ciscoBulkFileMIBObjects 1 } cbfStatus OBJECT IDENTIFIER ::= { ciscoBulkFileMIBObjects 2 } -- -- Bulk File Formats -- -- There are five bulk transfer file formats: -- . ASN.1/BER variable bindings - standard BER, just like you'd -- find it in the varbinds section of a Response PDU. -- . Bulk binary - a binary form designed for fast, sequential -- processing and minimum redundancy. -- . Bulk ASCII - the binary form, mechanically translated to -- human-readable ASCII. -- . Variant ASN.1/BER with Checksum - designed for more -- efficient data encoding to reduce the file size. -- . Variant Binary with Checksum - designed for speed and -- file size efficiency. -- The ASN.1/BER format is identical to SNMP variable bindings, that is, -- each object has a full OID and a fully tagged value. The file -- content is similar to what would be obtained with a GetBulk request -- except that it does not overshoot for uninstantiated values. In -- other words, the file contains no data at all for scalars or -- columns that could not be read. -- The Variant ASN.1/BER is different from the standard ASN.1/BER -- in the way it encodes each object and the checksum -- value it attaches at the end of the file. Here -- is the content structure of the Variant ASN.1/BER file: -- -- Checksum signature (4 bytes) -- Data (encoded in ASN.1/BER) -- Checksum signature (4 bytes) -- Checksum value (4 bytes) -- -- Here is an example of how the objects get encoded: -- 1) Common table subidentifier (share among multiple tables) -- 2) Common object subidentifier (share among object instances -- of a table) -- 3) Object instances -- Example: to encode ifDescr 1.3.6.1.2.1.2.2.1.2 -- ifType 1.3.6.1.2.1.2.2.1.3 -- ifName 1.3.6.1.2.1.31.1.1.1.1 -- using variant ASN.1/BER: -- 1) Common table subidentifier is 1.3.6.1.2.1 -- 2) Common object subidentifier for ifDescr and ifType -- are 2.1.2.2.1 -- Common object subidentifier for ifName is 31.1.1.1 -- 3) Object instance for -- ifDescr is 2.ifIndex -- ifType is 3.ifIndex -- ifName is 1.ifIndex -- -- The content of the the file encoded as: -- 1) 4 bytes checksum signature -- 2) Common table subidentifier encoded as private class -- OID type -- 3) Common object subidentifier for ifDesc encoded as -- private class OID type -- 4) ifDescr instance encoded as OID type -- 5) ifDescr value encdoded -- 6) ifType instance encoded as OID type -- 7) ifType value encoded -- 8) Repeat step 4-7 if the table contains multiple rows -- 9) Common object subidentifier for ifName encoded -- 10) ifName instance encoded as OID type -- 11) ifName value encoded -- 12) Repeat step 10-11 if the table contains multiple rows -- 13) 4 bytes checksum signature -- 14) 4 bytes checksum value -- -- Notes: Step 2 through step 12 are data -- The Variant Binary with Checksum is designed for fast -- processing and file size efficiency. The content of the the -- file is as follow: -- -- Checksum signature (4 bytes) -- Data -- Checksum signature (4 bytes) -- Checksum value (4 bytes) -- -- The data is store in 16 bytes blocks. Each block has -- 4 objects. Here is an example of the data: -- -- The remainder of this description applies to the bulk binary and bulk -- ASCII formats, not to the ASN.1/BER format. -- The file contains two types of fields: tags and data. Tags identify -- portions of the file and are discussed in detail below. All other -- information is in data fields. -- Note: For efficiency and compactness data fields are not tagged -- with a type. The interpreter of the data must thus know or have -- access to appropriate MIB syntax descriptions to understand the file. -- All data fields are positional relative to a tag and every data field -- has a length prefix. All initial length prefixes are one byte. For -- any data type the distinguished length value 255 indicates that the -- data content is null, that is, no data content value was -- available and there are no additional bytes in the data field. -- INTEGER data fields include all data that maps to ASN.1 INTEGER, -- regardless of length and whether signed or unsigned. They have a -- length prefix value of zero to eight, followed by that many bytes of -- data, high-order byte first. High order bytes that are all zero are -- omitted, thus a length of zero indicates a value of zero. For signed -- numbers, leading bytes of all ones (hex FF) are omitted if the next -- remaining byte has the high bit on. This implies that the -- file parser must know the difference between signed and unsigned -- integers. -- OCTET STRING values have a length prefix value of zero to two for a -- subsequent unsigned byte count for the number of bytes in the OCTET -- STRING itself, which immediately follows the byte count. The byte -- count can thus range from zero to 65,535. -- OBJECT IDENTIFIER values have a length of zero to 128, for the number -- of sub-identifiers. Each subsequent sub-identifier is encoded as an -- unsigned INTEGER of 0-4 bytes. -- The bulk binary file layout directly reflects the contents of the -- cbfDefineFileObjectTable. It has tagged sections corresponding to -- cbfDefineObjectClass with a few additional tags for utility purposes. -- A tag is one byte with one of the following values: -- -2 row -- -1 prefix -- 0 reserved -- 1 object -- 2 table -- The prefix tag changes the default OID prefix that is assumed to -- precede all OIDs that are not MIB object data values. The prefix tag -- may appear anywhere another tag could appear. A prefix tag is -- followed by one OID data field. The default prefix is 1.3.6.1. -- A file need not set the prefix to the default value. Note that -- when changing the prefix, the default portion must be included -- at the beginning of the new prefix. Typically the prefix will -- change for each table or group of scalar objects. -- An object tag is followed by one OID data field and one data field -- appropriate to the syntax of the object. This OID is the full -- OID for the object minus the current prefix. -- A table tag is followed by one INTEGER data field whose value is the -- number of columns in the table, as implemented by the agent. This is -- followed by one OID data field for each column. This is the OID for -- the column minus the prefix and the instance (typically one -- subidentifier). -- The OIDs are then followed by one row for each row in the table. -- A row starts with a row tag and one OID data field containing -- only the instance portion of the OIDs for the objects in that row. -- Following this is one data field of appropriate type for each -- column. -- The bulk ASCII form mechanically translates bulk binary into -- human-readable text. -- The indicator for a null value is "~". -- An INTEGER becomes the integer value with a preceding "-" for -- negative values and no leading zeros. -- An OCTET STRING becomes the byte values in hexadecimal, lower case, -- two characters per byte (that is, with leading zeros), no delimiters -- between bytes. -- An OBJECT IDENTIFIER becomes the usual dotted decimal form. -- A tag becomes the tag's name, spelled out fully in lower case, -- followed by one blank and the data field(s) for the tag, separated -- by spaces and ending with a carriage return/line feed. All tags -- are at the beginning of a "line" that is terminated with a carriage -- return/line feed that immediately precedes the next tag or the end -- of file. -- -- File Definition and Creation Control -- -- Definition Resource Management cbfDefineMaxFiles OBJECT-TYPE SYNTAX Unsigned32 (0..4294967295) MAX-ACCESS read-write STATUS current DESCRIPTION "The maximum number of file definitions this system can hold in cbfDefineFileTable. A value of 0 indicates no configured limit. This object may be read-only on some systems. Changing this number does not disturb existing entries." ::= { cbfDefine 1 } cbfDefineFiles OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The current number of file definitions in cbfDefineFileTable." ::= { cbfDefine 2 } cbfDefineHighFiles OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum value of cbfDefineFiles since system initialization." ::= { cbfDefine 3 } cbfDefineFilesRefused OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of attempts to create a file definition that failed due to exceeding cbfDefineMaxFiles." ::= { cbfDefine 4 } cbfDefineMaxObjects OBJECT-TYPE SYNTAX Unsigned32 (0..4294967295) MAX-ACCESS read-write STATUS current DESCRIPTION "The maximum total number of object selections to go with file definitions this system, that is, the total number of objects this system can hold in cbfDefineObjectTable. A value of 0 indicates no configured limit. This object may be read-only on some systems. Changing this number does not disturb existing entries." ::= { cbfDefine 5 } cbfDefineObjects OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The current number of object selections in cbfDefineObjectTable." ::= { cbfDefine 6 } cbfDefineHighObjects OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum value of cbfDefineObjects since system initialization." ::= { cbfDefine 7 } cbfDefineObjectsRefused OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of attempts to create an object selection that failed due to exceeding cbfDefineMaxObjects." ::= { cbfDefine 8 } -- File Definition Table cbfDefineFileTable OBJECT-TYPE SYNTAX SEQUENCE OF CbfDefineFileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of bulk file definition and creation controls." ::= { cbfDefine 9 } cbfDefineFileEntry OBJECT-TYPE SYNTAX CbfDefineFileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information for creation of a bulk file. To creat a bulk file an application creates an entry in this table and corresponding entries in cbfDefineObjectTable. When the entry in this table and the corresponding entries in cbfDefineObjectTable are 'active' the appliction uses cbfDefineFileNow to create the file and a corresponding entry in cbfStatusFileTable. Deleting an entry in cbfDefineFileTable deletes all corresponding entries in cbfDefineObjectTable and cbfStatusFileTable. An entry may not be modified or deleted while its cbfDefineFileNow has the value 'running'." INDEX { cbfDefineFileIndex } ::= { cbfDefineFileTable 1 } CbfDefineFileEntry ::= SEQUENCE { cbfDefineFileIndex Unsigned32, cbfDefineFileName DisplayString, cbfDefineFileStorage INTEGER, cbfDefineFileFormat INTEGER, cbfDefineFileNow INTEGER, cbfDefineFileEntryStatus RowStatus, cbfDefineFileNotifyOnCompletion TruthValue } cbfDefineFileIndex OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "An arbitrary integer to uniquely identify this entry. To create an entry a management application should pick a random number." ::= { cbfDefineFileEntry 1 } cbfDefineFileName OBJECT-TYPE SYNTAX DisplayString (SIZE (0..255)) MAX-ACCESS read-create STATUS current DESCRIPTION "The file name which is to be created. Explicit device or path choices in the value of this object override cbfDefineFileStorage." DEFVAL { "" } ::= { cbfDefineFileEntry 2 } cbfDefineFileStorage OBJECT-TYPE SYNTAX INTEGER { ephemeral(1), volatile(2), permanent(3) } MAX-ACCESS read-create STATUS current DESCRIPTION "The type of file storage to use: ephemeral data exists in small amounts until read volatile data exists in volatile memory permanent data survives reboot An ephemeral file is suitable to be read only one time. Note that this value is taken as advisory and may be overridden by explicit device or path choices in cbfDefineFile. A given system may support any or all of these." DEFVAL { ephemeral } ::= { cbfDefineFileEntry 3 } cbfDefineFileFormat OBJECT-TYPE SYNTAX INTEGER { standardBER(1), bulkBinary(2), bulkASCII(3), variantBERWithCksum(4), variantBinWithCksum(5) } MAX-ACCESS read-create STATUS current DESCRIPTION "The format of the data in the file: StandardBER standard SNMP ASN.1 BER bulkBinary a binary format specified with this MIB bulkASCII a human-readable form of bulkBinary variantBERWithCksum ASN.1 BER encoding with checksum variantBinWithCksum a binary format with checksum A given system may support any or all of these." DEFVAL { bulkBinary } ::= { cbfDefineFileEntry 4 } cbfDefineFileNow OBJECT-TYPE SYNTAX INTEGER { notActive(1), ready(2), create(3), running(4), forcedCreate(5) } MAX-ACCESS read-create STATUS current DESCRIPTION "The control to cause file creation. The only values that can be set are 'create' and 'forcedCreate'. These can be set only when the value is 'ready'. Setting it to 'create' begins a file creation and creates a corresponding entry in cbfStatusFileTable. The system may choose to use an already existing copy of the file instead of creating a new one. This may happen if there has been no configuration change on the system and a request to recreate the file is received. Setting this object to 'forcedCreate' forces the system to create a new copy of the file. The value is 'notActve' as long as cbfDefineFileEntryStatus or any corresponding cbfDefineObjectEntryStatus is not active. When cbfDefineFileEntryStatus becomes active and all corresponding cbfDefineObjectEntryStatuses are active this object automatically goes to 'ready'." DEFVAL { notActive } ::= { cbfDefineFileEntry 5 } cbfDefineFileEntryStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The control that allows creation, modification, and deletion of entries. For detailed rules see the DESCRIPTION for cbfDefineFileEntry." ::= { cbfDefineFileEntry 6 } cbfDefineFileNotifyOnCompletion OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "This controls the cbfDefineFileCompletion notification. If true, cbfDefineFileCompletion notification will be generated. It is the responsibility of the management entity to ensure that the SNMP administrative model is configured in such a way as to allow the notification to be delivered." DEFVAL { false } ::= { cbfDefineFileEntry 7 } -- File Object Table cbfDefineObjectTable OBJECT-TYPE SYNTAX SEQUENCE OF CbfDefineObjectEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of objects to go in bulk files." ::= { cbfDefine 10 } cbfDefineObjectEntry OBJECT-TYPE SYNTAX CbfDefineObjectEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about one object for a particular file. An application uses cbfDefineObjectEntryStatus to create entries in this table in correspondence with entries in cbfDefineFileTable, which must be created first. Entries in this table may not be changed, created or deleted while the corresponding value of cbfDefineFileNow is 'running'." INDEX { cbfDefineFileIndex, cbfDefineObjectIndex } ::= { cbfDefineObjectTable 1 } CbfDefineObjectEntry ::= SEQUENCE { cbfDefineObjectIndex Unsigned32, cbfDefineObjectClass INTEGER, cbfDefineObjectID OBJECT IDENTIFIER, cbfDefineObjectEntryStatus RowStatus, cbfDefineObjectTableInstance OBJECT IDENTIFIER, cbfDefineObjectNumEntries Unsigned32, cbfDefineObjectLastPolledInst OBJECT IDENTIFIER } cbfDefineObjectIndex OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "An arbitrary integer to uniquely identify this entry. The numeric order of the entries controls the order of the objects in the file." ::= { cbfDefineObjectEntry 1 } cbfDefineObjectClass OBJECT-TYPE SYNTAX INTEGER { object(1), lexicalTable(2), leastCpuTable(3) } MAX-ACCESS read-create STATUS current DESCRIPTION "The meaning of each object class is given below: object a single MIB object is retrieved. lexicalTable an entire table or partial table is retrieved in lexical order of rows. leastCpuTable an entire table is retrieved with lowest CPU utilization. Lexical ordering of rows may not be maintained and is dependent upon individual MIB implementation." DEFVAL { leastCpuTable } ::= { cbfDefineObjectEntry 2 } cbfDefineObjectID OBJECT-TYPE SYNTAX OBJECT IDENTIFIER MAX-ACCESS read-create STATUS current DESCRIPTION "The object identifier of a MIB object to be included in the file. If cbfDefineObjectClass is 'object' this must be a full OID, including all instance information. If cbfDefineObjectClass is 'lexicalTable' or 'leastCpuTable' this must be the OID of the table-defining SEQUENCE OF registration point." DEFVAL { zeroDotZero } ::= { cbfDefineObjectEntry 3 } cbfDefineObjectEntryStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The control that allows creation, modification, and deletion of entries. For detailed rules see the DESCRIPTION for cbfDefineObjectEntry." ::= { cbfDefineObjectEntry 4 } cbfDefineObjectTableInstance OBJECT-TYPE SYNTAX OBJECT IDENTIFIER MAX-ACCESS read-create STATUS current DESCRIPTION "If cbfDefineObjectClass is 'lexicalTable', then this object represents the starting instance in the cbfDefineObjectID table. The file created will have entries starting from the lexicographically next instance of the OID represented by this object. For Eg: ------- Let us assume we are polling ifTable and we have information till the second row(ifIndex.2). Now we may be interested in 10 rows lexically following the second row. So, we set cbfDefineObjectTableInstance as ifIndex.2 and cbfDefineObjectNumEntries as 10. We will get information for the next 10 rows or if there are less than 10 populated rows, we will receive information till the end of the table is reached. The default value for this object is zeroDotZero. If this object has the value of zeroDotZero and cbfDefineObjectNumEntries has value 0, then the whole table(represented by cbfDefineObjectID) is retrieved. If this object has the value of zeroDotZero, cbfDefineObjectNumEntries has value n (>0) and there are m(>0) entries in the table(represented by cbfDefineObjectID) then the first n entries in the table are retrieved if n < m. If n >= m, then the whole table is retrieved. When the value of cbfDefineObjectNumEntries is 0, it means all the entries in the table(represented by cbfDefineObjectID) which lexicographically follow cbfDefineObjectTableInstance are retrieved. This object is irrelevent if cbfDefineObjectClass is not 'lexicalTable'." DEFVAL { zeroDotZero } ::= { cbfDefineObjectEntry 5 } cbfDefineObjectNumEntries OBJECT-TYPE SYNTAX Unsigned32 (0..4294967295) MAX-ACCESS read-create STATUS current DESCRIPTION "If cbfDefineObjectClass is 'lexicalTable', then this object represents the maximum number of entries which will be populated in the file starting from the lexicographically next instance of the OID represented by cbfDefineObjectTableInstance. This object is irrelevent if cbfDefineObjectClass is not 'lexicalTable'. Refer to the description of cbfDefineObjectTableInstance for examples and different scenarios relating to this object." DEFVAL { 0 } ::= { cbfDefineObjectEntry 6 } cbfDefineObjectLastPolledInst OBJECT-TYPE SYNTAX OBJECT IDENTIFIER MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the last polled instance in the table. The value represented by this object will be relevent only if the corresponding cbfStatusFileState is emptied(3) for ephemeral files or ready(2) for volatile or permanent files. A value of zeroDotZero indicates an absence of last polled object. An NMS can use the value of this object and populate the cbfDefineObjectTableInstance to retrieve a contiguous set of rows in a table." ::= { cbfDefineObjectEntry 7 } -- -- File Status -- -- Resource Control cbfStatusMaxFiles OBJECT-TYPE SYNTAX Unsigned32 (0..4294967295) MAX-ACCESS read-write STATUS current DESCRIPTION "The maximum number of file statuses this system can hold in cbfStatusFileTable. A value of 0 indicates no configured limit. This object may be read-only on some systems. Changing this number deletes the oldest finished entries until the new limit is satisfied." ::= { cbfStatus 1 } cbfStatusFiles OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The current number of file statuses in cbfStatusFileTable." ::= { cbfStatus 2 } cbfStatusHighFiles OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum value of cbfStatusFiles since system initialization." ::= { cbfStatus 3 } cbfStatusFilesBumped OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number times the oldest entry was deleted due to exceeding cbfStatusMaxFiles." ::= { cbfStatus 4 } -- File Table cbfStatusFileTable OBJECT-TYPE SYNTAX SEQUENCE OF CbfStatusFileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of bulk file status." ::= { cbfStatus 5 } cbfStatusFileEntry OBJECT-TYPE SYNTAX CbfStatusFileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Status for a particular file. An entry exists in this table for each time cbfDefineFileNow has been set to 'create' and the corresponding entry here has not been explicitly deleted by the application or bumped to make room for a new entry. Deleting an entry with cbfStatusFileState 'running' aborts the file creation attempt. It is implementation and file-system specific whether deleting the entry also deletes the file." INDEX { cbfDefineFileIndex, cbfStatusFileIndex } ::= { cbfStatusFileTable 1 } CbfStatusFileEntry ::= SEQUENCE { cbfStatusFileIndex Unsigned32, cbfStatusFileState INTEGER, cbfStatusFileCompletionTime TimeStamp, cbfStatusFileEntryStatus RowStatus } cbfStatusFileIndex OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "An arbitrary integer to uniquely identify this file. The numeric order of the entries implies the creation order of the files." ::= { cbfStatusFileEntry 1 } cbfStatusFileState OBJECT-TYPE SYNTAX INTEGER { running(1), ready(2), emptied(3), noSpace(4), badName(5), writeErr(6), noMem(7), buffErr(8), aborted(9) } MAX-ACCESS read-only STATUS current DESCRIPTION "The file state: running data is being written to the file ready the file is ready to be read emptied an ephemeral file was successfully consumed noSpace no data due to insufficient file space badName no data due to a name or path problem writeErr no data due to fatal file write error noMem no data due to insufficient dynamic memory buffErr implementation buffer too small aborted short terminated by operator command Only the 'ready' state implies that the file is available for transfer. The disposition of files after an error is implementation and file-syste specific." ::= { cbfStatusFileEntry 2 } cbfStatusFileCompletionTime OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "The value of sysUpTime when the creation attempt completed. A value of 0 indicates not complete. For ephemeral files this is the time when cbfStatusFileState goes to 'emptied'. For others this is the time when the state leaves 'running'." ::= { cbfStatusFileEntry 3 } cbfStatusFileEntryStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-write STATUS current DESCRIPTION "The control that allows deletion of entries. For detailed rules see the DESCRIPTION for cbfStatusFileEntry. This object may not be set to any value other than 'destroy'." ::= { cbfStatusFileEntry 4 } -- Notifications ciscoBulkFileMIBNotificationPrefix OBJECT IDENTIFIER ::= { ciscoBulkFileMIB 2 } ciscoBulkFileMIBNotifications OBJECT IDENTIFIER ::= { ciscoBulkFileMIBNotificationPrefix 0 } cbfDefineFileCompletion NOTIFICATION-TYPE OBJECTS { cbfStatusFileState, cbfStatusFileCompletionTime } STATUS current DESCRIPTION "A cbfDefineFileCompletion notification is sent on the following conditions : - completion of a file consumption operation in case of ephemeral files. - completion of file creation operation in case of volatile or permanent files. - any error during file creation." ::= { ciscoBulkFileMIBNotifications 1 } -- -- Conformance -- ciscoBulkFileMIBConformance OBJECT IDENTIFIER ::= { ciscoBulkFileMIB 3 } ciscoBulkFileMIBCompliances OBJECT IDENTIFIER ::= { ciscoBulkFileMIBConformance 1 } ciscoBulkFileMIBGroups OBJECT IDENTIFIER ::= { ciscoBulkFileMIBConformance 2 } -- Compliance ciscoBulkFileMIBCompliance MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "The compliance statement for entities which implement the Cisco Bulk File MIB. Implementation of this MIB is based on individual product needs." MODULE -- this module MANDATORY-GROUPS { ciscoBulkFileDefineGroup, ciscoBulkFileStatusGroup, ciscoBulkFileNotiGroup } ::= { ciscoBulkFileMIBCompliances 1 } ciscoBulkFileMIBComplianceRev1 MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for entities which implement the Cisco Bulk File MIB. Implementation of this MIB is based on individual product needs." MODULE -- this module MANDATORY-GROUPS { ciscoBulkFileDefineGroupRev1, ciscoBulkFileStatusGroup, ciscoBulkFileNotiGroup } ::= { ciscoBulkFileMIBCompliances 2 } -- Units of Conformance ciscoBulkFileDefineGroup OBJECT-GROUP OBJECTS { cbfDefineMaxFiles, cbfDefineFiles, cbfDefineHighFiles, cbfDefineFilesRefused, cbfDefineMaxObjects, cbfDefineObjects, cbfDefineHighObjects, cbfDefineObjectsRefused, cbfDefineFileName, cbfDefineFileStorage, cbfDefineFileFormat, cbfDefineFileNow, cbfDefineFileEntryStatus, cbfDefineFileNotifyOnCompletion, cbfDefineObjectClass, cbfDefineObjectID, cbfDefineObjectEntryStatus } STATUS deprecated DESCRIPTION "Bulk file definition management." ::= { ciscoBulkFileMIBGroups 1 } ciscoBulkFileStatusGroup OBJECT-GROUP OBJECTS { cbfStatusMaxFiles, cbfStatusFiles, cbfStatusHighFiles, cbfStatusFilesBumped, cbfStatusFileState, cbfStatusFileCompletionTime, cbfStatusFileEntryStatus } STATUS current DESCRIPTION "Bulk file status management." ::= { ciscoBulkFileMIBGroups 2 } ciscoBulkFileNotiGroup NOTIFICATION-GROUP NOTIFICATIONS { cbfDefineFileCompletion } STATUS current DESCRIPTION "A collection of notification objects for supporting Bulk file notification management." ::= { ciscoBulkFileMIBGroups 3 } ciscoBulkFileDefineGroupRev1 OBJECT-GROUP OBJECTS { cbfDefineMaxFiles, cbfDefineFiles, cbfDefineHighFiles, cbfDefineFilesRefused, cbfDefineMaxObjects, cbfDefineObjects, cbfDefineHighObjects, cbfDefineObjectsRefused, cbfDefineFileName, cbfDefineFileStorage, cbfDefineFileFormat, cbfDefineFileNow, cbfDefineFileEntryStatus, cbfDefineFileNotifyOnCompletion, cbfDefineObjectClass, cbfDefineObjectID, cbfDefineObjectEntryStatus, cbfDefineObjectTableInstance, cbfDefineObjectNumEntries, cbfDefineObjectLastPolledInst } STATUS current DESCRIPTION "Bulk file definition management." ::= { ciscoBulkFileMIBGroups 4 } END