-- ***************************************************************** -- CISCO-ATM-SWITCH-FR-IWF-MIB -- -- Sept 1998, Vasmi Abidi -- -- Copyright (c) 1998, 1999, 2001 by Cisco Systems, Inc. -- All rights reserved. -- ***************************************************************** CISCO-ATM-SWITCH-FR-IWF-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, Integer32, Counter32 FROM SNMPv2-SMI TEXTUAL-CONVENTION, RowStatus, TimeStamp, TruthValue FROM SNMPv2-TC MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF ciscoMgmt FROM CISCO-SMI Unsigned32 FROM CISCO-TC AtmTrafficDescrParamIndex FROM ATM-MIB ifIndex, InterfaceIndex FROM IF-MIB; ciscoAtmSwitchFrIwfMIB MODULE-IDENTITY LAST-UPDATED "200105200000Z" ORGANIZATION "Cisco Systems" CONTACT-INFO " Cisco Systems, Inc. 170 West Tasman Drive, San Jose CA 95134-1706. Phone: +1 408 526 5260 Email: cs-atm@cisco.com" DESCRIPTION "A MIB module for managing Frame Relay to ATM interworking connections, and Frame Relay to Frame Relay switched connections via an ATM switching fabric, on a Cisco ATM switch." REVISION "200105200000Z" DESCRIPTION "Added objects casfVcSignalStandardCalledIe, casfConfIfCledSpvcDeModeDef, casfConfIfCledSpvcClpModeDef." REVISION "200002290000Z" DESCRIPTION "New UPC values of 'tag' and 'drop' were added for IDSL support." REVISION "9807090000Z" DESCRIPTION "Initial version." ::= { ciscoMgmt 112 } ciscoAtmSwitchFrIwfMIBObjects OBJECT IDENTIFIER ::= { ciscoAtmSwitchFrIwfMIB 1 } casfFrTraffic OBJECT IDENTIFIER ::= { ciscoAtmSwitchFrIwfMIBObjects 1 } casfFrVC OBJECT IDENTIFIER ::= { ciscoAtmSwitchFrIwfMIBObjects 2 } casfFrInterface OBJECT IDENTIFIER ::= { ciscoAtmSwitchFrIwfMIBObjects 3 } casfFrCounts OBJECT IDENTIFIER ::= { ciscoAtmSwitchFrIwfMIBObjects 4 } casfMapping OBJECT IDENTIFIER ::= { ciscoAtmSwitchFrIwfMIBObjects 5 } -- Textual Conventions CasfTrafficDescrRow ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Identifies an index into the casfTrafficDescrTable. The value 0 signifies that no row has been identified." SYNTAX Unsigned32 (1..2147483647) DlciValue ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "A numerical value identifying a Data Link Connection Identifier (DLCI) for a Frame Relay connection. The valid range of values depends on the format of the address field used, as described in ITU Recommendation Q.922. When a 2-octet address field is used, the value ranges from 0 to 1023." REFERENCE "ITU Recommendation Q.922, ISDN Data Link Layer Specification For Frame Mode Bearer Services." SYNTAX Integer32 (0..4194303) ConnectionKind ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The kind of connection, distinguished by the use of call control." SYNTAX INTEGER { pvc(1), svcIncoming(2), svcOutgoing(3), spvcInitiator(4), spvcTarget(5) } -- Copied from ATM-TC-MIB draft AtmAddr ::= TEXTUAL-CONVENTION DISPLAY-HINT "1x" STATUS current DESCRIPTION "An ATM address. The semantics are implied by the length. The address types are: - no address (0 octets) - E.164 (8 octets) - NSAP (20 octets) In addition, when subaddresses are used the AtmAddr may represent the concatenation of address and subaddress. The associated address types are: - E.164, E.164 (16 octets) - E.164, NSAP (28 octets) - NSAP, NSAP (40 octets) Address lengths other than defined in this definition imply address types defined elsewhere. Note: The E.164 address is encoded in BCD format." SYNTAX OCTET STRING (SIZE(0..40)) -- Modeling a Frame Relay to ATM interworking connection on an ATM switch: -- -- -- +___________________________+ -- | ATM SWITCH | -- | | -- | | -- F| P Switch Fabric |T -- _______O===O=======================O_______ ATM -- Frame | | -- Relay | | -- | | -- +___________________________+ -- -- -- Consider two ports 'F' and 'T' on a switch. -- Suppose 'F' is a frame relay port, connected to a frame relay network or -- DTE, and 'T' is an ATM port that is connected to an ATM network or DTE. -- In this model, the cross-connect between a Frame Relay leg (i.e. DLCI) on -- port F and an ATM leg (i.e., VPI/VCI) on port 'T' is represented using -- another ATM port 'P' that is internal to the switch. -- To create a FR-ATM interworking pvc connection, -- (1) Create a Frame relay connection leg on port F, using the table -- casfVcEndptTable. -- The agent will create a corresponding ATM connection leg on -- the internal ATM port P. The mapping from the FR leg to the -- ATM leg on the internal ATM port is created in the casfFAMapTable. -- The reverse mapping appears in the casfAFMapTable. -- (2) Create the ATM connection leg on port T, and the cross-connect -- between P and T using the usual ATM MIBS, e.g., the AToM MIB. -- -- To create a FR-ATM interworking soft VC connection, initiated from port F, -- (1) Create a Frame Relay connection leg on port F, using the -- casfVcEndptTable, also specify the value of the ATM Address -- of the soft VC target, and the DLCI value to -- be used at the target. The agent will initiate a soft VC -- setup, and will also create a corresponding ATM connection -- leg on the internal ATM port P. The mapping from the FR -- leg to the ATM leg on the internal ATM port is created in -- the casfFAMapTable. The reverse mapping appears in the -- casfAFMapTable. -- -- (2) Soft VC parameters, such as the retry interval, can be set -- on the internal ATM leg. -- Frame Relay Traffic Descriptor Table casfTrafficDescrTable OBJECT-TYPE SYNTAX SEQUENCE OF CasfTrafficDescrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains a set of self-consistent Frame Relay traffic parameters. It is intended to be used to create Frame Relay to ATM interworking connections, hence a ATM traffic service category is also included. An entry in this table is associated with an equivalent entry in the ATM traffic descriptor table (atmTrafficDescrParamTable); the mapping is given by the object casfTrafficDescrAtmIndex. The agent will not permit deletion of the associated atmTrafficDescrEntry while the Frame Relay Traffic Descriptor entry exists. When creating an entry in this table, if the value of casfTrafficDescrAtmIndex is specified, the following cases are possible: (a) if no corresponding row exists in atmTrafficDescrParamTable, the agent will create such a row with the given index value. (b) if a corresponding row does exist in atmTrafficDescrParamTable, the agent compares the parameter values in casfTrafficDescrEntry and the corresponding atmTrafficDescrParamEntry. If the two entries are not equivalent, an error is returned, and row creation fails. When creating an entry in this table, if the value of casfTrafficDescrAtmIndex is not specified, the agent will assign a value to this object so that it refers to an equivalent entry in the atmTrafficDescrParamTable. If such an equivalent entry does not already exist, the agent will create one. The agent creates rows in this table for use with signaled connections. These are called 'transient' rows - they disappear when the connection is torn down, and are not saved in non-volatile memory. By convention, transient rows usually use high-numbered index values. Entries can be deleted by setting the row status to destroy(6). The agent denies the request if the row is in use by existing connections." ::= { casfFrTraffic 1 } casfTrafficDescrEntry OBJECT-TYPE SYNTAX CasfTrafficDescrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Describes a traffic descriptor that is used by Frame Relay connections." INDEX { casfTrafficDescrIndex } ::= { casfTrafficDescrTable 1 } CasfTrafficDescrEntry ::= SEQUENCE { casfTrafficDescrIndex CasfTrafficDescrRow, casfTrafficDescrCIR Unsigned32, casfTrafficDescrBc Unsigned32, casfTrafficDescrBe Unsigned32, casfTrafficDescrPIR Unsigned32, casfTrafficDescrServCategory INTEGER, casfTrafficDescrAtmIndex AtmTrafficDescrParamIndex, casfTrafficDescrRowStatus RowStatus } casfTrafficDescrIndex OBJECT-TYPE SYNTAX CasfTrafficDescrRow MAX-ACCESS not-accessible STATUS current DESCRIPTION "Uniquely identifies a row in this table." ::= { casfTrafficDescrEntry 1 } casfTrafficDescrCIR OBJECT-TYPE SYNTAX Unsigned32 UNITS "bits/sec" MAX-ACCESS read-create STATUS current DESCRIPTION "The value of the Committed Information Rate (CIR) parameter." ::= { casfTrafficDescrEntry 2 } casfTrafficDescrBc OBJECT-TYPE SYNTAX Unsigned32 UNITS "bits" MAX-ACCESS read-create STATUS current DESCRIPTION "The value of the Committed Burst Size (Bc) parameter." ::= { casfTrafficDescrEntry 3 } casfTrafficDescrBe OBJECT-TYPE SYNTAX Unsigned32 UNITS "bits" MAX-ACCESS read-create STATUS current DESCRIPTION "The value of the Excess Burst Size (Be) parameter." ::= { casfTrafficDescrEntry 4 } casfTrafficDescrPIR OBJECT-TYPE SYNTAX Unsigned32 UNITS "bits/sec" MAX-ACCESS read-create STATUS current DESCRIPTION "The value of the Peak Information Rate (PIR) parameter." ::= { casfTrafficDescrEntry 5 } casfTrafficDescrServCategory OBJECT-TYPE SYNTAX INTEGER { vbrNrt(1), -- non real-time variable bit rate abr(2), -- available bit rate ubr(3), -- unspecified bit rate vbrRt(4) -- real-time variable bit rate } MAX-ACCESS read-create STATUS current DESCRIPTION "The service category, as defined for ATM." REFERENCE "ATM Forum Traffic Management Specification, Version 4.0, af-tm-0056.000, June 1996." ::= { casfTrafficDescrEntry 6 } casfTrafficDescrAtmIndex OBJECT-TYPE SYNTAX AtmTrafficDescrParamIndex MAX-ACCESS read-create STATUS current DESCRIPTION "The index of the equivalent entry in the atmTrafficDescrParamTable." ::= { casfTrafficDescrEntry 7 } casfTrafficDescrRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Used to create, delete and modify this row. None of the columnar values (other than this one) can be modified while the row is active." ::= { casfTrafficDescrEntry 8 } -- Configuring Connections -- Note: Here the term "end-point" does not indicate the termination -- of a connection. Rather, we are using the terminology of RFC -- 1604. In this context, each PVC segment has two end-points, which -- are connected together through the switch. An end-point is -- identified by a UNI/NNI logical port index value and a DLCI value. casfVcEndptTable OBJECT-TYPE SYNTAX SEQUENCE OF CasfVcEndptEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains information about Frame Relay end-points of FR-ATM interworking connections on the switch. When an entry is created in this table, the agent creates a corresponding entry in the atmVclTable of ATM-MIB, to represent the configuration on the internal ATM port. The mapping between an entry in this table, and the corresponding entry in the atmVclTable is shown in the casfFAMapTable and the casfAFMapTable. Entries can be created or deleted in this table by an NMS using the casfVcEndptRowStatus object. To create a PVC connection end-point, the value of casfVcEndptConnKind must be 'pvc'. To create a soft VC initiator end-point, set the value of casfVcEndptConnKind to 'spvcInitiator', and specify the value of casfVcEndptSpvcRemoteAddr and casfVcEndptSpvcRemoteType. If the value of casfVcEndptSpvcRemoteType is 'frameRelay', you must also specify the value of casfVcEndptSpvcRemoteDlci. Activating the conceptual row will then cause the agent to attempt to establish a connection to the remote frame relay interface. If the value of casfVcEndptSpvcRemoteType is 'atm', you must specify the values of casfVcEndptSpvcRemoteVpi and casfVcEndptSpvcRemoteVci. Activating the conceptual row will then cause the agent to attempt to establish a connection to the remote ATM interface. The agent creates an entry in this table when an incoming signaling request causes a soft VC connection to be established with a local frame relay interface as the destination. The value of casfVcEndptConnKind in this case will be 'spvcTarget'. Such entries cannot be modified or deleted by network management. They will be deleted when the connection is removed by signaling." ::= { casfFrVC 1 } casfVcEndptEntry OBJECT-TYPE SYNTAX CasfVcEndptEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Models a bidirectional Frame Relay VC end-point. The ifIndex identifies an ifTable entry for a Frame Relay interface on this device." INDEX { ifIndex, casfVcEndptDlci } ::= { casfVcEndptTable 1 } CasfVcEndptEntry ::= SEQUENCE { casfVcEndptDlci DlciValue, casfVcEndptRxTrafficDescrRow CasfTrafficDescrRow, casfVcEndptTxTrafficDescrRow CasfTrafficDescrRow, casfVcEndptRxNegTrafficDescrRow CasfTrafficDescrRow, casfVcEndptTxNegTrafficDescrRow CasfTrafficDescrRow, casfVcEndptConnKind ConnectionKind, casfVcEndptIwfType INTEGER, casfVcEndptClpMode INTEGER, casfVcEndptDeMode INTEGER, casfVcEndptEfciMode INTEGER, casfVcEndptUpcMode INTEGER, casfVcEndptSpvcRemoteAddr AtmAddr, casfVcEndptSpvcRemoteType INTEGER, casfVcEndptSpvcRemoteDlci DlciValue, casfVcEndptSpvcRemoteVpi INTEGER, casfVcEndptSpvcRemoteVci INTEGER, casfVcEndptCreationTime TimeStamp, casfVcEndptRcvdSigStatus INTEGER, casfVcEndptRowStatus RowStatus, casfVcSignalStandardCalledIe TruthValue } casfVcEndptDlci OBJECT-TYPE SYNTAX DlciValue MAX-ACCESS not-accessible STATUS current DESCRIPTION "The value of the Data Link Connection Identifier (DLCI) which identifies this connection end-point." ::= { casfVcEndptEntry 1 } casfVcEndptRxTrafficDescrRow OBJECT-TYPE SYNTAX CasfTrafficDescrRow MAX-ACCESS read-create STATUS current DESCRIPTION "Identifies the entry in the casfTrafficDescrTable which applies to the receive direction at this connection end-point. For connections that negotiate traffic parameters through signaling (e.g. ABR connections), this object points to the desired traffic parameters, while the object casfVcEndptRxNegTrafficDescrRow points to the negotiated traffic parameters, for the receive direction." ::= { casfVcEndptEntry 2 } casfVcEndptTxTrafficDescrRow OBJECT-TYPE SYNTAX CasfTrafficDescrRow MAX-ACCESS read-create STATUS current DESCRIPTION "Identifies the entry in the casfTrafficDescrTable which applies to the transmit direction at this connection end-point. For connections that negotiate traffic parameters through signaling (e.g. ABR connections), this object points to the desired traffic parameters, while the object casfVcEndptTxNegTrafficDescrRow points to the negotiated traffic parameter, for the transmit direction." ::= { casfVcEndptEntry 3 } casfVcEndptRxNegTrafficDescrRow OBJECT-TYPE SYNTAX CasfTrafficDescrRow MAX-ACCESS read-only STATUS current DESCRIPTION "Identifies the entry in the casfTrafficDescrTable which contains negotiated traffic parameters applied to the receive direction of this connection end-point. This object is not instantiated if this is not the calling side of a soft VC, or if there is no traffic negotiation." ::= { casfVcEndptEntry 4 } casfVcEndptTxNegTrafficDescrRow OBJECT-TYPE SYNTAX CasfTrafficDescrRow MAX-ACCESS read-only STATUS current DESCRIPTION "Identifies the entry in the casfTrafficDescrTable which contains negotiated traffic parameters applied to the transmit direction of this connection endpoint. This object is not instantiated if this is not the calling side of a soft VC, or if there is no traffic negotiation." ::= { casfVcEndptEntry 5 } casfVcEndptConnKind OBJECT-TYPE SYNTAX ConnectionKind MAX-ACCESS read-create STATUS current DESCRIPTION "The connection kind. The value can be set prior to the row becoming 'active'. To create a pvc connection endpoint, set this value to pvc(1). To create a soft VC connection endpoint, set this value to spvcInitiator(4), and specify the value of casfVcEndptSpvcRemoteAddr. The values svcIncoming(2), svcOutgoing(3), and spvcTarget(5) can not be written." DEFVAL { pvc } ::= { casfVcEndptEntry 6 } casfVcEndptIwfType OBJECT-TYPE SYNTAX INTEGER { network(1), -- as in FRF.5 serviceTransparent(2), -- as in FRF.8 serviceTranslation(3), -- as in FRF.8 rfc1973(4) -- PPP in Frame Relay } MAX-ACCESS read-create STATUS current DESCRIPTION "The type of the interworking function. The value can be set prior to the row becoming 'active'." ::= { casfVcEndptEntry 7 } casfVcEndptClpMode OBJECT-TYPE SYNTAX INTEGER { clpIfDe(1), -- Mode 1 of FRF.5, FRF.8 clpIsZero(2), -- Mode 2 of FRF.5, FRF.8 clpIsOne(3) -- Mode 2 of FRF.5, FRF.8 } MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies how to map from Discard Eligibility (DE) bit on the Frame Relay side to Congestion Loss Priority (CLP) bit on the ATM side. For network interworking, clpIfDe(1) corresponds to Mode 1 as defined in FRF.5, section 4.4.1. clpIsZero(2) and clpIsOne(3) correspond to Mode 2 as defined in FRF.5, section 4.4.1. For service interworking, clpIfDe(1) corresponds to Mode 1 as defined in FRF.8, section 4.2.1. clpIsZero(2) and clpIsOne(3) correspond to Mode 2 as defined in FRF.8, section 4.2.1." ::= { casfVcEndptEntry 8 } casfVcEndptDeMode OBJECT-TYPE SYNTAX INTEGER { deIfClpOrFrsscsDe(1), deIfFrsscsDe(2), deIfClp(3), deIsZero(4), deIsOne(5) } MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies how to map from Congestion Loss Priority (CLP) bit on the ATM side to Discard Eligibility (DE) bit on the Frame Relay side. See the Frame Relay Forum specifications FRF.5 and FRF.8 for definitions of Mode 1 and Mode 2. For network interworking, the valid values are: deIfClpOrFrsscsDe(1) -- Mode 1 of FRF.5 section 4.4.2 deIfFrsscsDe(2) -- Mode 2 of FRF.5 section 4.4.2 For service interworking, the valid values are: deIfClp(3) -- Mode 1 of FRF.8 section 4.2.2 deIsZero(4) and deIsOne(5) -- Mode 2 of FRF.8 section 4.2.2 " ::= { casfVcEndptEntry 9 } casfVcEndptEfciMode OBJECT-TYPE SYNTAX INTEGER { efciIfFecn(1), efciIsZero(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies how to map from FECN field in the Frame Relay PDU to the EFCI field in ATM cells, in case of service interworking. This object does not apply to network interworking. efciIfFecn(1) and efciIsZero(2) correspond to Mode 1 and Mode 2 (as defined in FRF.8, section 4.3.1.1), respectively." ::= { casfVcEndptEntry 10 } casfVcEndptUpcMode OBJECT-TYPE SYNTAX INTEGER { pass(1), tagDrop(2), tag(3), drop(4) } MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the action taken by Usage Parameter Control (UPC) at the ingress port." ::= { casfVcEndptEntry 11 } casfVcEndptSpvcRemoteAddr OBJECT-TYPE SYNTAX AtmAddr MAX-ACCESS read-create STATUS current DESCRIPTION "The ATM address of the remote end of the soft VC. The value can be set prior to the row becoming 'active', and if the value of casfVcEndptConnKind is spvcInitiator(4). The agent will return an inconsistentValue error on sets if the value of casfVcEndptConnKind is other than spvcInitiator(4). If the value of casfVcEndptConnKind spvcTarget(5), this object is initialized by the agent. This object is instantiated only if the value of casfVcEndptConnKind is spvcInitiator(4) or spvcTarget(5)." ::= { casfVcEndptEntry 12 } casfVcEndptSpvcRemoteType OBJECT-TYPE SYNTAX INTEGER { other(1), frameRelay(2), atm(3) } MAX-ACCESS read-create STATUS current DESCRIPTION "The type of the remote end of the soft VC. This object is instantiated only if the value of casfVcEndptConnKind is spvcInitiator(4) or spvcTarget(5). The agent will return an inconsistentValue error on sets if the value of casfVcEndptConnKind is other than spvcInitiator(4) or spvcTarget(5)." ::= { casfVcEndptEntry 13 } casfVcEndptSpvcRemoteDlci OBJECT-TYPE SYNTAX DlciValue MAX-ACCESS read-create STATUS current DESCRIPTION "The DLCI value to be used at the remote end of the soft VC. The value can be set prior to the row becoming 'active', and if the value of casfVcEndptConnKind is spvcInitiator(4), and the value of casfVcEndptSpvcRemoteType is frameRelay(2). The object is instantiated only if the value of casfVcEndptSpvcRemoteType is frameRelay(2). The agent will return an inconsistentValue error on sets if the value of casfVcEndptSpvcRemoteType is other than frameRelay(2)." ::= { casfVcEndptEntry 14 } casfVcEndptSpvcRemoteVpi OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-create STATUS current DESCRIPTION "The VPI value to be used at the remote end of the soft VC. The value can be set prior to the row becoming 'active', and if the value of casfVcEndptConnKind is spvcInitiator(4), and the value of casfVcEndptSpvcRemoteType is atm(3). The object is instantiated only if the value of casfVcEndptSpvcRemoteType is atm(3). The agent will return an inconsistentValue error on sets if the value of casfVcEndptSpvcRemoteType is other than atm(3)." ::= { casfVcEndptEntry 15 } casfVcEndptSpvcRemoteVci OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-create STATUS current DESCRIPTION "The VCI value to be used at the remote end of the soft VC. The value can be set prior to the row becoming 'active', and if the value of casfVcEndptConnKind is spvcInitiator(4), and the value of casfVcEndptSpvcRemoteType is atm(3). The object is instantiated only if the value of casfVcEndptSpvcRemoteType is atm(3). The agent will return an inconsistentValue error on sets if the value of casfVcEndptSpvcRemoteType is other than atm(3)." ::= { casfVcEndptEntry 16 } casfVcEndptCreationTime OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "The time when this row was created." ::= { casfVcEndptEntry 17 } casfVcEndptRcvdSigStatus OBJECT-TYPE SYNTAX INTEGER { deleted(1), active(2), inactive(3), none(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object identifies the PVC status received via the local in-channel signaling procedures for this PVC end-point. This object is only pertinent for interfaces that perform the bidirectional procedures. For user-to-network network side procedures, the value of this object should be none(4)." REFERENCE " Q.933 Annex A. This object is a copy of frPVCEndptRcvdSigStatus from RFC1604." ::= { casfVcEndptEntry 18 } casfVcEndptRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Used to create, modify or delete this row." ::= { casfVcEndptEntry 19 } casfVcSignalStandardCalledIe OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies whether or not to signal the standard (from the ATM-Forum PNNI Soft PVC Addendum) format of the Called Soft PVC IE, as opposed to the proprietary encoding we have used for the network-interworking case to a frame-relay destination." REFERENCE " ATM Forum specification AF-CS-0127.000 for standard encoding of Soft PVC IE." DEFVAL { false } ::= { casfVcEndptEntry 20 } -- LMI at a Frame Relay Interface casfFrLmiTable OBJECT-TYPE SYNTAX SEQUENCE OF CasfFrLmiEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains frame relay Local Management Interface (LMI) parameters and counters. There is one entry for each frame relay interface. Entries come and go in this table as frame relay interfaces are created and deleted in the device." ::= { casfFrInterface 1 } casfFrLmiEntry OBJECT-TYPE SYNTAX CasfFrLmiEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Frame relay LMI objects for a particular frame relay interface, which is identified by the ifIndex value in the INDEX clause." INDEX { ifIndex } ::= { casfFrLmiTable 1 } CasfFrLmiEntry ::= SEQUENCE { casfFrLmiProtocol INTEGER, casfFrLmiType INTEGER, casfFrLmiUserN391 INTEGER, casfFrLmiUserN392 INTEGER, casfFrLmiUserN393 INTEGER, casfFrLmiUserT391 INTEGER, casfFrLmiNetN392 INTEGER, casfFrLmiNetN393 INTEGER, casfFrLmiNetT392 INTEGER, casfFrLmiEnquiryIns Counter32, casfFrLmiEnquiryOuts Counter32, casfFrLmiStatusIns Counter32, casfFrLmiStatusOuts Counter32, casfFrLmiStatusTimeouts Counter32, casfFrLmiStatusEnqTimeouts Counter32 } casfFrLmiProtocol OBJECT-TYPE SYNTAX INTEGER { none(1), lmi(2), ansiT1617D(3), -- ANSI T1.617 Annex D ansiT1617B(4), -- ANSI T1.617 Annex B ccittQ933A(5) } MAX-ACCESS read-write STATUS current DESCRIPTION "Identifies the Local In-Channel Signaling Protocol that is used for this frame relay port." ::= { casfFrLmiEntry 1 } casfFrLmiType OBJECT-TYPE SYNTAX INTEGER { dte(1), dce(2), nni(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Identifies the Local In-Channel Signaling Procedure that is used for this frame relay port. A dte performs only user-side procedures. A dce performs only network-side procedures. An nni performs bidirectional procedures." ::= { casfFrLmiEntry 2 } casfFrLmiUserN391 OBJECT-TYPE SYNTAX INTEGER (1..255) MAX-ACCESS read-write STATUS current DESCRIPTION "Number of status enquiry intervals that pass before issuance of a full status enquiry mes- sage." REFERENCE "Draft American National Standard T1.617-1991, Section D.7 Counter N391." DEFVAL { 6 } ::= { casfFrLmiEntry 3 } casfFrLmiUserN392 OBJECT-TYPE SYNTAX INTEGER (1..10) MAX-ACCESS read-write STATUS current DESCRIPTION "The maximum number of unanswered Status Enquiries the device shall accept before declaring the interface down." REFERENCE "Draft American National Standard T1.617-1991, Section D.5.1 Counter N392." DEFVAL { 3 } ::= { casfFrLmiEntry 4 } casfFrLmiUserN393 OBJECT-TYPE SYNTAX INTEGER (1..10) MAX-ACCESS read-write STATUS current DESCRIPTION "The number of status polling intervals over which the error threshold is counted. For example, if within N393 number of events the device receives N392 number of errors, the interface is marked as down." REFERENCE "Draft American National Standard T1.617-1991, Section D.5.2 Counter N393." DEFVAL { 4 } ::= { casfFrLmiEntry 5 } casfFrLmiUserT391 OBJECT-TYPE SYNTAX INTEGER (5..30) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "The number of seconds between successive status enquiry messages." REFERENCE "Draft American National Standard T1.617-1991, Section D.7 Timer T391." DEFVAL { 10 } ::= { casfFrLmiEntry 6 } casfFrLmiNetN392 OBJECT-TYPE SYNTAX INTEGER (1..10) MAX-ACCESS read-write STATUS current DESCRIPTION "The value of the network-side error threshold for this frame relay port." REFERENCE "Draft American National Standard T1.617-1991, Section D.7 Timer N392." DEFVAL { 3 } ::= { casfFrLmiEntry 7 } casfFrLmiNetN393 OBJECT-TYPE SYNTAX INTEGER (0..10) MAX-ACCESS read-write STATUS current DESCRIPTION "The value of the network-side monitored events count for this frame relay port. If, within N393 number of events, the network-side receives N392 number of errors, the interface is marked as down." REFERENCE "Draft American National Standard T1.617-1991, Section D.7 Timer N393." DEFVAL { 3 } ::= { casfFrLmiEntry 8 } casfFrLmiNetT392 OBJECT-TYPE SYNTAX INTEGER (5..30) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "The value of the network-side polling verification timer for this frame relay port." REFERENCE "Draft American National Standard T1.617-1991, Section D.7 Timer T392." DEFVAL { 15 } ::= { casfFrLmiEntry 9 } casfFrLmiEnquiryIns OBJECT-TYPE SYNTAX Counter32 UNITS "messages" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of Status Enquiry messages received." ::= { casfFrLmiEntry 10 } casfFrLmiEnquiryOuts OBJECT-TYPE SYNTAX Counter32 UNITS "messages" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of Status Enquiry messages sent." ::= { casfFrLmiEntry 11 } casfFrLmiStatusIns OBJECT-TYPE SYNTAX Counter32 UNITS "messages" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of Status messages received." ::= { casfFrLmiEntry 12 } casfFrLmiStatusOuts OBJECT-TYPE SYNTAX Counter32 UNITS "messages" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of Status messages sent." ::= { casfFrLmiEntry 13 } casfFrLmiStatusTimeouts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of times when timeout occurred on waiting for Status message" ::= { casfFrLmiEntry 14 } casfFrLmiStatusEnqTimeouts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of times when timeout occurred on waiting for Status Enquiry message" ::= { casfFrLmiEntry 15 } -- Configuration at a Frame Relay interface casfConfIfTable OBJECT-TYPE SYNTAX SEQUENCE OF CasfConfIfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Contains an entry for each Frame Relay interface that supports FR-ATM interworking connections. An entry contains interworking related parameters for the interface." ::= { casfFrInterface 2 } casfConfIfEntry OBJECT-TYPE SYNTAX CasfConfIfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Configuration parameters for interworking at a Frame Relay interface." INDEX { ifIndex } ::= { casfConfIfTable 1 } CasfConfIfEntry ::= SEQUENCE { casfConfIfAtmAddress AtmAddr, casfConfIfUpcIntent INTEGER, casfConfIfBcDefault Integer32, casfConfIfCledSpvcDeModeDef INTEGER, casfConfIfCledSpvcClpModeDef INTEGER } casfConfIfAtmAddress OBJECT-TYPE SYNTAX AtmAddr MAX-ACCESS read-only STATUS current DESCRIPTION "The ATM Address that identifies this interface. This address can be used to setup soft VC's to this interface over an ATM network." ::= { casfConfIfEntry 1 } casfConfIfUpcIntent OBJECT-TYPE SYNTAX INTEGER { pass(1), tagDrop(2), tag(3), drop(4) } MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the default Usage Parameter Control (UPC) action to use at this interface for connections that do not explicitly specify a UPC action." ::= { casfConfIfEntry 2 } casfConfIfBcDefault OBJECT-TYPE SYNTAX Integer32 (0..32768) UNITS "bits" MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the default Committed Burst Size (Bc) value to use at this interface for connections that do not explicitly specify the value of Bc." ::= { casfConfIfEntry 3 } casfConfIfCledSpvcDeModeDef OBJECT-TYPE SYNTAX INTEGER { deIfClpOrFrsscsDe(1), deIfFrsscsDe(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the default mapping from Congestion Loss Priority (CLP) bit on the ATM side to Discard Eligibility (DE) bit on the Frame Relay side. This is used when receiving a soft PVC Setup using the standard encoding of the called Soft PVC IE. Otherwise a proprietary encoding provides this information." REFERENCE " ATM Forum specification AF-CS-0127.000 for standard encoding of Soft PVC IE." DEFVAL { deIfClpOrFrsscsDe } ::= { casfConfIfEntry 4 } casfConfIfCledSpvcClpModeDef OBJECT-TYPE SYNTAX INTEGER { clpIfDe(1), -- Mode 1 of FRF.5, FRF.8 clpIfIsZero(2), -- Mode 2 of FRF.5, FRF.8 clpIfIsOne(3) -- Mode 2 of FRF.5, FRF.8 } MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the default mapping from Discard Eligibility (DE) bit on the Frame Relay side to Congestion Loss Priority (CLP) bit on the ATM side.This is used when receiving a soft PVC Setup using the standard encoding of the called Soft PVC IE. Otherwise a proprietary encoding provides this information." REFERENCE " ATM Forum specification AF-CS-0127.000 for standard encoding of Soft PVC IE." DEFVAL { clpIfDe } ::= { casfConfIfEntry 5 } -- Per-connection Counters at a Frame Relay end-point casfVcCountTable OBJECT-TYPE SYNTAX SEQUENCE OF CasfVcCountEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table containing counters at Frame Relay connection end-points. Entries in this table are created and deleted whenever corresponding entries in the casfVcEndptTable are created and deleted." ::= { casfFrCounts 1 } casfVcCountEntry OBJECT-TYPE SYNTAX CasfVcCountEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Counters at a Frame Relay connection end-point, which is identified by the ifIndex of the Frame Relay interface and the DLCI number." INDEX { ifIndex, casfVcEndptDlci } ::= { casfVcCountTable 1 } CasfVcCountEntry ::= SEQUENCE { casfVcCountReceivedFrames Counter32, casfVcCountReceivedOctets Counter32, casfVcCountReceivedFECNs Counter32, casfVcCountReceivedBECNs Counter32, casfVcCountReceivedDEs Counter32, casfVcCountInDiscards Counter32, casfVcCountOutDiscards Counter32, casfVcCountSentFrames Counter32, casfVcCountSentOctets Counter32, casfVcCountSentFECNs Counter32, casfVcCountSentBECNs Counter32, casfVcCountSentDEs Counter32, casfVcCountTaggedFECNs Counter32, casfVcCountTaggedBECNs Counter32, casfVcCountTaggedDEs Counter32 } casfVcCountReceivedFrames OBJECT-TYPE SYNTAX Counter32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of frames received." ::= { casfVcCountEntry 1 } casfVcCountReceivedOctets OBJECT-TYPE SYNTAX Counter32 UNITS "octets" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of octets received. This counter counts octets from the beginning of the frame relay header field to the end of user data." ::= { casfVcCountEntry 2 } casfVcCountReceivedFECNs OBJECT-TYPE SYNTAX Counter32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of frames received from the network with the FECN (Forward Explicit Congestion Notification) bit set." ::= { casfVcCountEntry 3 } casfVcCountReceivedBECNs OBJECT-TYPE SYNTAX Counter32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of frames received from the network with the BECN (Backward Explicit Network Congestion) bit set." ::= { casfVcCountEntry 4 } casfVcCountReceivedDEs OBJECT-TYPE SYNTAX Counter32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of frames received with the Discard Eligibility (DE) bit set." ::= { casfVcCountEntry 5 } casfVcCountInDiscards OBJECT-TYPE SYNTAX Counter32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of frames received that were discarded at ingress. Possible reasons are policing, congestion." ::= { casfVcCountEntry 6 } casfVcCountOutDiscards OBJECT-TYPE SYNTAX Counter32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of frames that were to be transmitted but were discarded. Possible reasons are policing, lack of buffers." ::= { casfVcCountEntry 7 } casfVcCountSentFrames OBJECT-TYPE SYNTAX Counter32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of frames sent." ::= { casfVcCountEntry 8 } casfVcCountSentOctets OBJECT-TYPE SYNTAX Counter32 UNITS "octets" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of octets sent. This counter counts octets from the beginning of the frame relay header field to the end of user data." ::= { casfVcCountEntry 9 } casfVcCountSentFECNs OBJECT-TYPE SYNTAX Counter32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of frames that were sent with the FECN bit set." ::= { casfVcCountEntry 10 } casfVcCountSentBECNs OBJECT-TYPE SYNTAX Counter32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of frames sent with the BECN bit set." ::= { casfVcCountEntry 11 } casfVcCountSentDEs OBJECT-TYPE SYNTAX Counter32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of frames sent with the DE bit set." ::= { casfVcCountEntry 12 } casfVcCountTaggedFECNs OBJECT-TYPE SYNTAX Counter32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of frames for which the switch set the FECN bit." ::= { casfVcCountEntry 13 } casfVcCountTaggedBECNs OBJECT-TYPE SYNTAX Counter32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of frames for which the switch set the BECN bit." ::= { casfVcCountEntry 14 } casfVcCountTaggedDEs OBJECT-TYPE SYNTAX Counter32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of frames for which the switch set the DE bit." ::= { casfVcCountEntry 15 } -- per-connection counters relevant to FR-ATM interworking casfVcIwfCountTable OBJECT-TYPE SYNTAX SEQUENCE OF CasfVcIwfCountEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains counters at the Frame Relay endpoint of FR-ATM interworking connections. There is an entry in this table corresponding to each entry in casfVcEndptTable." ::= { casfFrCounts 2 } casfVcIwfCountEntry OBJECT-TYPE SYNTAX CasfVcIwfCountEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A set of counters at the Frame Relay endpoint of a FR-ATM interworking connection." INDEX { ifIndex, casfVcEndptDlci } ::= { casfVcIwfCountTable 1 } CasfVcIwfCountEntry ::= SEQUENCE { casfVcIwfCountInUnknownProts Counter32, casfVcIwfCountOutUnknownProts Counter32, casfVcIwfCountReassemblyTimeouts Counter32, casfVcIwfCountLengthErrors Counter32, casfVcIwfCountCrcErrors Counter32, casfVcIwfCountTotalDiscardFrames Counter32 } casfVcIwfCountInUnknownProts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Frames received with unknown protocol. This event is counted only for connections with service interworking in translation mode. For other types of connections, this count will remain at zero." ::= { casfVcIwfCountEntry 1 } casfVcIwfCountOutUnknownProts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Outbound frames that were not transmitted because they contained an unknown protocol. This event is counted only for connections with service interworking in translation mode. For other types of connections, this count will remain at zero." ::= { casfVcIwfCountEntry 2 } casfVcIwfCountReassemblyTimeouts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of frames which could not be completely reassembled due to a reassembly timeout, and were thus discarded before being transmitted on this connection." ::= { casfVcIwfCountEntry 3 } casfVcIwfCountLengthErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of reassembled frames intended to be transmitted on this connection for which the AAL5 PDU trailer length fields did not match the actual PDU length, and were thus discarded." ::= { casfVcIwfCountEntry 4 } casfVcIwfCountCrcErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of reassembled frames intended to be transmitted on this connection for which the AAL5 PDU had CRC errors, and were thus discarded." ::= { casfVcIwfCountEntry 5 } casfVcIwfCountTotalDiscardFrames OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of frames intended to be transmitted on this connection that were discarded due to any reason including those described in other objects in this table (e.g., frames that were discarded because insufficient buffer space was available for reassembling the frame)." ::= { casfVcIwfCountEntry 6 } -- Mapping from a Frame Relay connection end-point to an ATM VCL casfFAMapTable OBJECT-TYPE SYNTAX SEQUENCE OF CasfFAMapEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides mapping from a DLCI on a Frame Relay interface to a VPI/VCI on an internal ATM interface." ::= { casfMapping 1 } casfFAMapEntry OBJECT-TYPE SYNTAX CasfFAMapEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Given the ifIndex of a frame relay interface, and a DLCI on that interface, this entry provides the ifIndex and VPI/VCI on the corresponding internal atm interface." INDEX { ifIndex, casfFAMapDlci } ::= { casfFAMapTable 1 } CasfFAMapEntry ::= SEQUENCE { casfFAMapDlci DlciValue, casfFAMapInternalAtmInterface InterfaceIndex, casfFAMapInternalAtmVpi INTEGER, casfFAMapInternalAtmVci INTEGER } casfFAMapDlci OBJECT-TYPE SYNTAX DlciValue MAX-ACCESS not-accessible STATUS current DESCRIPTION "The DLCI value." ::= { casfFAMapEntry 1 } casfFAMapInternalAtmInterface OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-only STATUS current DESCRIPTION "The ifIndex of the internal ATM interface to which this DLCI is mapped." ::= { casfFAMapEntry 2 } casfFAMapInternalAtmVpi OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "The VPI value to which this DLCI is mapped." ::= { casfFAMapEntry 3 } casfFAMapInternalAtmVci OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The VCI value to which this DLCI is mapped." ::= { casfFAMapEntry 4 } -- Mapping from an ATM VCL to a Frame Relay connection end-point casfAFMapTable OBJECT-TYPE SYNTAX SEQUENCE OF CasfAFMapEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides mapping from an atmVclEntry on an internal ATM internal to a casfVcEndptEntry on a Frame Relay interface." ::= { casfMapping 2 } casfAFMapEntry OBJECT-TYPE SYNTAX CasfAFMapEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Given the ifIndex of an internal ATM interface, and VPI/VCI, provides the ifIndex of a Frame Relay interface and DLCI, if such mapping exists. The value of ifType for an internal ATM interface is propVirtual(53). For every such interface on the switch, this table contains an entry for each virtual channel link (VCL) that maps to a frame relay connection. Entries in this table come and go as the corresponding frame relay connections come and go." INDEX { ifIndex, casfAFMapAtmVpi, casfAFMapAtmVci } ::= { casfAFMapTable 1 } CasfAFMapEntry ::= SEQUENCE { casfAFMapAtmVpi INTEGER, casfAFMapAtmVci INTEGER, casfAFMapFrIndex InterfaceIndex, casfAFMapFrDlci DlciValue } casfAFMapAtmVpi OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The VPI value of the Virtual Channel Link (VCL) on the ATM interface." ::= { casfAFMapEntry 1 } casfAFMapAtmVci OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The VCI value of the Virtual Channel Link (VCL) on the ATM interface." ::= { casfAFMapEntry 2 } casfAFMapFrIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-only STATUS current DESCRIPTION "The ifIndex of the frame relay interface that this VCL maps to." ::= { casfAFMapEntry 3 } casfAFMapFrDlci OBJECT-TYPE SYNTAX DlciValue MAX-ACCESS read-only STATUS current DESCRIPTION "The DLCI on the frame relay interface that this VCL maps to." ::= { casfAFMapEntry 4 } ciscoAtmSFrIwfMIBConformance OBJECT IDENTIFIER ::= { ciscoAtmSwitchFrIwfMIB 3 } ciscoAtmSFrIwfMIBCompliances OBJECT IDENTIFIER ::= { ciscoAtmSFrIwfMIBConformance 1 } ciscoAtmSFrIwfMIBGroups OBJECT IDENTIFIER ::= { ciscoAtmSFrIwfMIBConformance 2 } -- Conformance ciscoAtmSFrIwfMIBCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for entities which implement the Cisco Atm Switch FR IWF MIB." MODULE -- this module MANDATORY-GROUPS { ciscoAtmSFrIwfConfConnGroup, ciscoAtmSFrIwfLmiGroup, ciscoAtmSFrIwfConfIfGroup, ciscoAtmSFrIwfVcStatsGroup, ciscoAtmSFrIwfVcIwStatsGroup, ciscoAtmSFrIwfMappingGroup } ::= { ciscoAtmSFrIwfMIBCompliances 1 } -- Units of Conformance ciscoAtmSFrIwfConfConnGroup OBJECT-GROUP OBJECTS { casfTrafficDescrCIR, casfTrafficDescrBc, casfTrafficDescrBe, casfTrafficDescrPIR, casfTrafficDescrServCategory, casfTrafficDescrAtmIndex, casfTrafficDescrRowStatus, casfVcEndptRxTrafficDescrRow, casfVcEndptTxTrafficDescrRow, casfVcEndptRxNegTrafficDescrRow, casfVcEndptTxNegTrafficDescrRow, casfVcEndptConnKind, casfVcEndptIwfType, casfVcEndptClpMode, casfVcEndptDeMode, casfVcEndptEfciMode, casfVcEndptUpcMode, casfVcEndptCreationTime, casfVcEndptRcvdSigStatus, casfVcEndptSpvcRemoteAddr, casfVcEndptSpvcRemoteType, casfVcEndptSpvcRemoteDlci, casfVcEndptSpvcRemoteVpi, casfVcEndptSpvcRemoteVci, casfVcEndptRowStatus, casfVcSignalStandardCalledIe } STATUS current DESCRIPTION "A collection of objects which allow configuration of FR-ATM connections on an ATM switch." ::= { ciscoAtmSFrIwfMIBGroups 1 } ciscoAtmSFrIwfLmiGroup OBJECT-GROUP OBJECTS { casfFrLmiProtocol, casfFrLmiType, casfFrLmiUserN391, casfFrLmiUserN392, casfFrLmiUserN393, casfFrLmiUserT391, casfFrLmiNetN392, casfFrLmiNetN393, casfFrLmiNetT392, casfFrLmiEnquiryIns, casfFrLmiEnquiryOuts, casfFrLmiStatusIns, casfFrLmiStatusOuts, casfFrLmiStatusTimeouts, casfFrLmiStatusEnqTimeouts } STATUS current DESCRIPTION "A collection of objects for configuring and monitoring LMI on an FR interface." ::= { ciscoAtmSFrIwfMIBGroups 2 } ciscoAtmSFrIwfConfIfGroup OBJECT-GROUP OBJECTS { casfConfIfAtmAddress, casfConfIfUpcIntent, casfConfIfBcDefault, casfConfIfCledSpvcDeModeDef, casfConfIfCledSpvcClpModeDef } STATUS current DESCRIPTION "A collection of objects which allow configuration of interworking related parameters on an FR interface." ::= { ciscoAtmSFrIwfMIBGroups 3 } ciscoAtmSFrIwfVcStatsGroup OBJECT-GROUP OBJECTS { casfVcCountReceivedFrames, casfVcCountReceivedOctets, casfVcCountReceivedFECNs, casfVcCountReceivedBECNs, casfVcCountReceivedDEs, casfVcCountInDiscards, casfVcCountOutDiscards, casfVcCountSentFrames, casfVcCountSentOctets, casfVcCountSentFECNs, casfVcCountSentBECNs, casfVcCountSentDEs, casfVcCountTaggedFECNs, casfVcCountTaggedBECNs, casfVcCountTaggedDEs } STATUS current DESCRIPTION "A collection of counters at FR VC end-points." ::= { ciscoAtmSFrIwfMIBGroups 4 } ciscoAtmSFrIwfVcIwStatsGroup OBJECT-GROUP OBJECTS { casfVcIwfCountInUnknownProts, casfVcIwfCountOutUnknownProts, casfVcIwfCountReassemblyTimeouts, casfVcIwfCountLengthErrors, casfVcIwfCountCrcErrors, casfVcIwfCountTotalDiscardFrames } STATUS current DESCRIPTION "A collection of counters related to FR-ATM interworking at FR VC end-points." ::= { ciscoAtmSFrIwfMIBGroups 5 } ciscoAtmSFrIwfMappingGroup OBJECT-GROUP OBJECTS { casfFAMapInternalAtmInterface, casfFAMapInternalAtmVpi, casfFAMapInternalAtmVci, casfAFMapFrIndex, casfAFMapFrDlci } STATUS current DESCRIPTION "A collection of objects that describe the mapping from a FR connection end-point to an ATM VCL, and vice versa." ::= { ciscoAtmSFrIwfMIBGroups 6 } END