-- -- ***************************************************************** -- C I S C O A T M R e s o u r c e M a n a g e m e n t M I B -- -- December 1995, Michael Grobelch -- -- Copyright (c) 1996-2001 by cisco Systems, Inc. -- All rights reserved. -- ***************************************************************** -- CISCO-ATM-RM-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, Counter32, Gauge32, Unsigned32 FROM SNMPv2-SMI TEXTUAL-CONVENTION,DisplayString, TruthValue FROM SNMPv2-TC ifIndex FROM RFC1213-MIB ciscoExperiment FROM CISCO-SMI MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF; ciscoAtmRmMIB MODULE-IDENTITY LAST-UPDATED "200206030000Z" ORGANIZATION "Cisco System Inc." CONTACT-INFO " Cisco Systems Customer Service Postal: 170 W Tasman Drive San Jose, CA 95134 USA Tel: +1 800 553-NETS E-mail: cs-atm@cisco.com" DESCRIPTION "The MIB module which complements standard ATM MIBs for Cisco devices, for Resource Management." REVISION "200206030000Z" DESCRIPTION "Added objects to support Per Class Overbooking for ATM interfaces." REVISION "200101290000Z" DESCRIPTION "Added a table that contains objects to manage ATM Traffic Shaper configuration and state information for ATM interfaces." REVISION "9912220000Z" DESCRIPTION "Fix the errors in the definition of cgrPerVcqAtmRmGroup." REVISION "9907270000Z" DESCRIPTION "Added object to support overbooking of equivalent bandwidth of an ATM interface." REVISION "9904300000Z" DESCRIPTION " Added objects for the IMA interface support." REVISION "9904140000Z" DESCRIPTION "Added objects to instruct Connection Admission Control to include framing overhead in the calculation of maximum cell rate of an ATM interface." REVISION "9903110000Z" DESCRIPTION "Clarified the description for some of the objects that they are applicable to logical port ATM interfaces too and made appropriate changes to the Compliance section." REVISION "9811240000Z" DESCRIPTION "Added a table to manage global resources on the Catalyst8540MSR platform. This was necessary because the Catalyst8540MSR, has 8 switching modules internally, with each switching module having its own independent cell memory. Each switching module performs per-VC queueing for a specific (fixed in hardware) group of ports, independent of any other switching module. The Lightstream 1010 had only one global cell memory for the entire device. " REVISION "9811030000Z" DESCRIPTION "Specify a range limiting Link Distance object." REVISION "9807260000Z" DESCRIPTION "Added an object to enable Hierarchical Scheduling." REVISION "9712030000Z" DESCRIPTION "Added object to configure Service Category support on an interface." REVISION "9705260000Z" DESCRIPTION "Added objects for management of new features made possible on the LS1010 by the Feature Card Plus. This includes support for per-VC queueing hardware structures, enhanced UPC, non-zero MCR for ABR, and UBR+." REVISION "9611110000Z" DESCRIPTION "Added objects for management of Cell Loss Ratio for CLP0+1 cell-streams. Added table for default tolerance." ::= { ciscoExperiment 10 } -- -- Caution. This MIB is temporary and experimental. -- In the future willbe removed from products, -- perhaps with short notice, in favor of more standard -- or generic MIBs. Application developers should not -- depend on long-term access to this MIB. -- ciscoAtmRmMIBObjects OBJECT IDENTIFIER ::= { ciscoAtmRmMIB 1 } ForceValue ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "This data type is used to provide a standard mechanism for providing protection on writing to objects. An object of type ForceValue is associated with the protected object. If an set request is made for the protected object, the state of the system or the value to be set may violate the intended protection. The value of the associated object of type ForceValue is then used to determine whether the set request succeeds or fails: - value is forceChange, request succeeds. - value is noForceChange, request fails. An additional characteristic of the ForceValue type is that the setting of the protected object resets the value of the protection object to noForceChange. As an example, take an object limiting the number of network connections on an interface (named maxNetConn). If maxNetConn is set below the number of currently active connections, some of those connections will be cleared. An associated protection object of type ForceValue (named maxNetConnForce) is used to protect the setting of maxNetConn. If the setting of maxNetConn would cause the clearing of connections, maxNetConnForce must be set to forceChange. Whenever maxNetConn is successfully set, maxNetConnForce assumes the value noForceChange." SYNTAX INTEGER { forceChange(1), noForceChange(2) } FineQueueThreshold ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "This data type is used to represent thresholds for output-queues on a shared memory ATM switch." SYNTAX INTEGER { percent12(1), percent25(2), percent37(3), percent50(4), percent62(5), percent75(6), percent87(7), percent100(8) } LsPerVcqServiceClass ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "This data type is used to represent one of the Service Classes." SYNTAX INTEGER { c1(1), -- Service class 1 (highest SP priority) c2(2), -- Service class 2 (2nd highest SP priority) c3(3), -- Service class 3 c4(4), -- Service class 4 c5(5), -- Service class 5 (lowest SP priority) c6(6), -- reserved c7(7), -- reserved c8(8) -- reserved } LsPerVcqServiceClassNoC1 ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "This data type is used to represent one of the Service Classes, omitting c1." SYNTAX INTEGER { c2(2), -- Service class 2 (2nd highest SP priority) c3(3), -- Service class 3 c4(4), -- Service class 4 c5(5), -- Service class 5 (lowest SP priority) c6(6), -- reserved c7(7), -- reserved c8(8) -- reserved } LsPerVcqThresholdGroup ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "This data type is used to represent one of the Threshold Groups." SYNTAX INTEGER { tg1(1), -- Threshold Group 1 tg2(2), -- Threshold Group 2 tg3(3), -- Threshold Group 3 tg4(4), -- Threshold Group 4 tg5(5), -- Threshold Group 5 tg6(6), -- Threshold Group 6 tg7(7), -- reserved tg8(8), -- reserved tg9(9), -- reserved tg10(10), -- reserved tg11(11), -- reserved tg12(12), -- reserved tg13(13), -- reserved tg14(14), -- reserved tg15(15), -- reserved tg16(16) -- reserved } LsPerVcqThresholdGroupService ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "This data type is used to specify how VC/VP queues are assigned to Threshold Groups." SYNTAX INTEGER { cbr(1), vbrRt(2), vbrNrt(3), abr(4), ubr(5) } CgrPerVcqModuleId ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The Catalyst8540MSR has 8 switching modules. Each module has its own cell memory, and performs its own congestion control, independent of the other switching modules." SYNTAX INTEGER { module1(1), module2(2), module3(3), module4(4), module5(5), module6(6), module7(7), module8(8) } -- This MIB defines the following Groups: -- -- 1. the ATM Switch Resource Management Configuration Group -- 2. the Shared-Memory architecture ATM Switch Resource Management Group -- 3. the ATM Interface Resource Management Configuration Group -- 4. the ATM Interface Resource Management State Group -- 5. the ATM Interface Resource Management Statistics Group -- 6. the Shared-Memory architecture ATM Interface Resource Management Group -- 7. the Lightstream per-VC queueing chipset ATM Switch Resource -- Management Group -- 8. the Lightstream per-VC queueing switch chipset ATM Interface Resource -- Management Group -- 9. The Catalyst8540MSR per-VC queueing chipset ATM Switch Resource -- Management Group -- 10. The ATM Traffic Shaper Interface Management Group ciscoAtmRmSwitchCfg OBJECT IDENTIFIER ::= { ciscoAtmRmMIBObjects 1 } ciscoAtmRmSwitchSharedMem OBJECT IDENTIFIER ::= { ciscoAtmRmMIBObjects 2 } ciscoAtmRmIfCfg OBJECT IDENTIFIER ::= { ciscoAtmRmMIBObjects 3 } ciscoAtmRmIfState OBJECT IDENTIFIER ::= { ciscoAtmRmMIBObjects 4 } ciscoAtmRmIfStatistics OBJECT IDENTIFIER ::= { ciscoAtmRmMIBObjects 5 } ciscoAtmRmIfSharedMem OBJECT IDENTIFIER ::= { ciscoAtmRmMIBObjects 6 } ciscoLsPerVcqAtmRmSwitch OBJECT IDENTIFIER ::= { ciscoAtmRmMIBObjects 7 } ciscoLsPerVcqAtmRmIf OBJECT IDENTIFIER ::= { ciscoAtmRmMIBObjects 8 } ciscoCgrPerVcqAtmRmSwitch OBJECT IDENTIFIER ::= { ciscoAtmRmMIBObjects 9 } ciscoAtmRmTrafShaperIf OBJECT IDENTIFIER ::= { ciscoAtmRmMIBObjects 10 } -- -- The ATM Switch Resource Management Configuration Group -- rmSwitchOverSubFactor OBJECT-TYPE SYNTAX INTEGER (1..32) MAX-ACCESS read-write STATUS current DESCRIPTION "The Over Subscription Factor (OSF) is used on switch startup/OIR to determine the maximum sizes of VBR-NRT and ABR/UBR queues. In general, the larger the value of OSF specified, the larger the queues are made at startup. Denoting the maximum sizes of CBR,VBR-RT, VBR-NRT, and ABR/UBR output queues for a physical interface as L1, L2, L3, and L4, respectively, an example algorithm is: L3 = .25 * (OSF*(2048-L1 -L2) L4 = .75 * (OSF*(2048-L1 -L2)" DEFVAL { 4 } ::= { ciscoAtmRmSwitchCfg 1 } rmSwitchScrMarginFactor OBJECT-TYPE SYNTAX INTEGER (0..100) MAX-ACCESS read-write STATUS current DESCRIPTION "The Sustained Cell Rate Margin Factor (SCRMF) is used in Connection Admission Control (CAC) of VBR connections to vary the weight given to the difference between Sustained Cell Rate (scr) and Peak Cell Rate (pcr) specified in the traffic contract. When calculating the equivalent bandwidth offered by a connection, SCRMF is used as follows: eqBw = scr + ((pcr - scr) * rcacVbrScrmf) / 100" DEFVAL { 1 } ::= { ciscoAtmRmSwitchCfg 2 } rmSwitchAbrCongNotify OBJECT-TYPE SYNTAX INTEGER { relativeRate(1), efci(2), efciAndRelativeRate(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "The ABR Congestion Notification object determines the type of congestion notification used on ABR connections in the switch. This notification can be done either via relative-rate or Explicit Forward Congestion Indication marking in ATM cells, or both." DEFVAL { relativeRate } ::= { ciscoAtmRmSwitchCfg 3 } rmDefaultQosObjectiveTable OBJECT-TYPE SYNTAX SEQUENCE OF RmDefaultQosObjectiveEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The (conceptual) table containing Resource Management configuration information for default Quality of Service objective values used when a signalling request is received on a UNI interface." ::= { ciscoAtmRmSwitchCfg 4 } rmDefaultQosObjectiveEntry OBJECT-TYPE SYNTAX RmDefaultQosObjectiveEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in the rmDefaultQosObjectiveTable containing Resource Management configuration for the default UNI QOS objectives. Rows are identified by Service Category." INDEX { rmDefaultQosServiceCategory } ::= { rmDefaultQosObjectiveTable 1 } RmDefaultQosObjectiveEntry ::= SEQUENCE { rmDefaultQosServiceCategory INTEGER, rmScDefaultQosMaxCtd INTEGER, rmScDefaultQosPeakToPeakCdv INTEGER, rmScDefaultQosClr INTEGER, rmScDefaultQosClrClp01 INTEGER } rmDefaultQosServiceCategory OBJECT-TYPE SYNTAX INTEGER { cbr(1), --constant-bit-rate vbrRt(2), --variable-bit-rate-real-time vbrNrt(3) --variable-bit-rate-non-real-time } MAX-ACCESS not-accessible STATUS current DESCRIPTION "The Service Category to which the row applies." ::= { rmDefaultQosObjectiveEntry 1 } rmScDefaultQosMaxCtd OBJECT-TYPE SYNTAX INTEGER (0..16777215) UNITS "microseconds" MAX-ACCESS read-write STATUS current DESCRIPTION "The default Maximum Cell Transfer Delay (ctd) for the Service Category. It applies only to cbr and vbr-rt Service Categories. Specifying a value of 16777215 signifies that this parameter should not be checked during connection setup. The units of this object are microseconds." DEFVAL { 16777215 } ::= { rmDefaultQosObjectiveEntry 2 } rmScDefaultQosPeakToPeakCdv OBJECT-TYPE SYNTAX INTEGER (0..16777215) UNITS "microseconds" MAX-ACCESS read-write STATUS current DESCRIPTION "The default Peak-to-peak cell delay variation (cdv) for the Service Category. It applies only to cbr and vbr-rt Service Categories. Specifying a value of 16777215 signifies that this parameter should not be checked during connection setup. The units of this object are microseconds." DEFVAL { 16777215 } ::= { rmDefaultQosObjectiveEntry 3 } rmScDefaultQosClr OBJECT-TYPE SYNTAX INTEGER (0..15) MAX-ACCESS read-write STATUS current DESCRIPTION "The default cell-loss-ratio for the Service Category (for CLP=0 cells only). Specifying a value of 0 signifies that this parameter should not be checked during connection setup. The units of this object are negative powers of ten (so an object value of 8 means 10**(-8))." DEFVAL { 0 } ::= { rmDefaultQosObjectiveEntry 4 } rmScDefaultQosClrClp01 OBJECT-TYPE SYNTAX INTEGER (0..15) MAX-ACCESS read-write STATUS current DESCRIPTION "The default cell-loss-ratio for the Service Category for CLP=0+1 cells. Specifying a value of 0 signifies that this parameter should not be checked during connection setup. The units of this object are negative powers of ten (so an object value of 8 means 10**(-8))." DEFVAL { 0 } ::= { rmDefaultQosObjectiveEntry 5 } -- -- The cisco ATM Switch Shared Memory Architecture Resource Management Group -- sharedMemRmSwitchQueuedCellTable OBJECT-TYPE SYNTAX SEQUENCE OF SharedMemRmSwitchQueuedCellEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The (conceptual) table containing Resource Management information on the cells in the output queues of a shared-memory output-queued ATM switch." ::= { ciscoAtmRmSwitchSharedMem 1 } sharedMemRmSwitchQueuedCellEntry OBJECT-TYPE SYNTAX SharedMemRmSwitchQueuedCellEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in the sharedMemRmSwitchQueuedCellTable containing Resource Management information on the cells in the output queues of a shared-memory switch. Rows are indexed by priority." INDEX { sharedMemRmCellPriority } ::= { sharedMemRmSwitchQueuedCellTable 1 } SharedMemRmSwitchQueuedCellEntry ::= SEQUENCE { sharedMemRmCellPriority INTEGER, sharedMemRmSwitchQueuedCellLimit INTEGER, sharedMemRmSwitchQueuedCellCount Gauge32 } sharedMemRmCellPriority OBJECT-TYPE SYNTAX INTEGER { p1(1), -- Priority 1 (highest priority) p2(2), -- Priority 2 (2nd highest priority) p3(3), -- Priority 3 (3rd highest priority) p4(4) -- Priority 4 (lowest priority) } MAX-ACCESS not-accessible STATUS current DESCRIPTION "The cell priority. The cell priority maps one-to-one to the per-interface queues specified by the sharedMemRmIfOutputQ object. All cells of a connection of a particular Service Category are given a fixed priority. The Service Categories allocated to a priority can be determined by querying the sharedMemRmIfOutputQServCategory object for any physical interface on the switch." ::= { sharedMemRmSwitchQueuedCellEntry 1 } sharedMemRmSwitchQueuedCellLimit OBJECT-TYPE SYNTAX INTEGER (0..65535) UNITS "cells" MAX-ACCESS read-write STATUS current DESCRIPTION "Configured limit on the number of cells on all output queues of the switch at any time of a particular priority." DEFVAL { 65535 } ::= { sharedMemRmSwitchQueuedCellEntry 2 } sharedMemRmSwitchQueuedCellCount OBJECT-TYPE SYNTAX Gauge32 UNITS "cells" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of the number of cells on all output queues of the switch at any time of a particular priority." ::= { sharedMemRmSwitchQueuedCellEntry 3 } -- -- The ATM Interface Resource Management Configuration Group -- rmIfCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF RmIfCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The (conceptual) table containing Resource Management configuration information for whole ATM interfaces." ::= { ciscoAtmRmIfCfg 3 } rmIfCfgEntry OBJECT-TYPE SYNTAX RmIfCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in the rmIfCfgTable containing Resource Management configuration for an ATM interface. The particular interface is identified by the value of MIB-II's ifIndex." INDEX { ifIndex } ::= { rmIfCfgTable 1 } RmIfCfgEntry ::= SEQUENCE { rmIfOutPacingRateRequested Unsigned32, rmIfOutPacingRateInstalled Unsigned32, rmIfOutPacingForce ForceValue, rmIfLinkDistance Unsigned32, rmIfBestEffortLimit Unsigned32, rmIfCbrDefaultRxUpcTolerance Unsigned32, rmIfVbrRtDefaultRxUpcTolerance Unsigned32, rmIfVbrNrtDefaultRxUpcTolerance Unsigned32, rmIfAbrDefaultRxUpcTolerance Unsigned32, rmIfUbrDefaultRxUpcTolerance Unsigned32, rmIfVbrRtDefaultRxUpcCdvt Unsigned32, rmIfVbrNrtDefaultRxUpcCdvt Unsigned32, rmIfServCategorySupport INTEGER, rmIfFramingOverhead TruthValue, rmIfFramingOverheadForce ForceValue, rmIfOverBooking INTEGER, rmIfVbrRtPerClassOverbooking INTEGER, rmIfVbrNrtPerClassOverbooking INTEGER, rmIfAbrPerClassOverbooking INTEGER, rmIfUbrPerClassOverbooking INTEGER } rmIfOutPacingRateRequested OBJECT-TYPE SYNTAX Unsigned32 UNITS "kilobits-per-second" MAX-ACCESS read-write STATUS current DESCRIPTION "This object reflects an explicit configuration of the state of pacing for this interface. If the value of this object is 0, pacing is disabled on this interface. Prior to any user configuration, the value of this object is 0. If the value not 0, it represents the output pacing value, in kilobits per second. The hardware is not capable of providing all possible rates. The rate in place is available in rmIfOutPacingRateInstalled. If the value specified would reduce the port rate below that currently allocated to Guaranteed Service bandwidth for the output flow, the rmIfOutPacingForce object must be set in conjunction with this object in order to cause the change to take effect." DEFVAL { 0 } ::= { rmIfCfgEntry 1 } rmIfOutPacingRateInstalled OBJECT-TYPE SYNTAX Unsigned32 UNITS "kilobits-per-second" MAX-ACCESS read-only STATUS current DESCRIPTION "The output pacing value, in kilobits per second, in effect. A value of 0 indicates output pacing is disabled. This object is not instantiated for interfaces to which it cannot be applied." DEFVAL { 0 } ::= { rmIfCfgEntry 2 } rmIfOutPacingForce OBJECT-TYPE SYNTAX ForceValue MAX-ACCESS read-write STATUS current DESCRIPTION "A Set Request for rmIfOutPacingRateRequested that does not reduce the port rate below the currently allocated bandwidth guarantees for the output flow always succeeds irrespective of the value of rmIfOutPacingForce. But a Set Request for rmIfOutPacingRateRequested that does reduce the port rate below the currently allocated bandwidth guarantees for the output flow will succeed only if rmIfOutPacingForce object is also set to the value forceChange. In either of the above cases, once rmIfOutPacingRateRequested object is set to the appropriate value, rmIfOutPacingForce object assumes the noForceChange value. This object is not instantiated for interfaces to which it cannot be applied." DEFVAL { noForceChange } ::= { rmIfCfgEntry 3 } rmIfLinkDistance OBJECT-TYPE SYNTAX Unsigned32 (0..65535) UNITS "kilometers" MAX-ACCESS read-write STATUS current DESCRIPTION "The link distance defined for the interface, expressed in kilometers. This is then divided by the speed of light to determine a propagation delay." DEFVAL { 0 } ::= { rmIfCfgEntry 4 } rmIfBestEffortLimit OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "The limit on the number of Best Effort connections that can be established on this interface. Note that a change to this value affects subsequent connection setup, not existing connections. A value of 4294967295 disables best-effort limits." DEFVAL { 4294967295 } ::= { rmIfCfgEntry 5 } rmIfCbrDefaultRxUpcTolerance OBJECT-TYPE SYNTAX Unsigned32 UNITS "cell-times" MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the GCRA limit parameter used for policing of a receive cell-stream of a CBR connection on an interface, if the limit parameter is not specified explicitly in the connection setup request. It is specified in cell-times. Note that a change to this value affects subsequent connection setup, not existing connections." DEFVAL { 1024 } ::= { rmIfCfgEntry 6 } rmIfVbrRtDefaultRxUpcTolerance OBJECT-TYPE SYNTAX Unsigned32 UNITS "cell-times" MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the maximum burst size parameter used for policing of a receive cell-stream of a VBR-RT connection on an interface, if this parameter is not specified explicitly in the connection setup request. It is specified in cell-times. Note that a change to this value affects subsequent connection setup, not existing connections." DEFVAL { 1024 } ::= { rmIfCfgEntry 7 } rmIfVbrNrtDefaultRxUpcTolerance OBJECT-TYPE SYNTAX Unsigned32 UNITS "cell-times" MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the maximum burst size parameter used for policing of a receive cell-stream of a VBR-NRT connection on an interface, if this parameter is not specified explicitly in the connection setup request. It is specified in cell-times. Note that a change to this value affects subsequent connection setup, not existing connections." DEFVAL { 1024 } ::= { rmIfCfgEntry 8 } rmIfAbrDefaultRxUpcTolerance OBJECT-TYPE SYNTAX Unsigned32 UNITS "cell-times" MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the GCRA limit parameter used for policing of a receive cell-stream of an ABR connection on an interface, if the limit parameter is not specified explicitly in the connection setup request. It is specified in cell-times. Note that a change to this value affects subsequent connection setup, not existing connections." DEFVAL { 1024 } ::= { rmIfCfgEntry 9 } rmIfUbrDefaultRxUpcTolerance OBJECT-TYPE SYNTAX Unsigned32 UNITS "cell-times" MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the GCRA limit parameter used for policing of a receive cell-stream of a UBR connection on an interface, if the limit parameter is not specified explicitly in the connection setup request. It is specified in cell-times. Note that a change to this value affects subsequent connection setup, not existing connections." DEFVAL { 1024 } ::= { rmIfCfgEntry 10 } rmIfVbrRtDefaultRxUpcCdvt OBJECT-TYPE SYNTAX Unsigned32 UNITS "cell-times" MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the GCRA limit parameter used for peak-rate policing of a receive cell-stream of a VBR-RT connection on an interface, if the CDVT parameter is not specified explicitly in the connection setup request. It is specified in cell-times. Note that a change to this value affects subsequent connection setup, not existing connections." DEFVAL { 1024 } ::= { rmIfCfgEntry 11 } rmIfVbrNrtDefaultRxUpcCdvt OBJECT-TYPE SYNTAX Unsigned32 UNITS "cell-times" MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the GCRA limit parameter used for peak-rate policing of a receive cell-stream of a VBR-NRT connection on an interface, if the CDVT parameter is not specified explicitly in the connection setup request. It is specified in cell-times. Note that a change to this value affects subsequent connection setup, not existing connections." DEFVAL { 1024 } ::= { rmIfCfgEntry 12 } rmIfServCategorySupport OBJECT-TYPE SYNTAX INTEGER (0..31) MAX-ACCESS read-write STATUS current DESCRIPTION "The value of this object controls and reflects the Service Category(s) supported on this ATM interface. If a bit is set, the corresponding Service Category is supported on the interface, and CAC will allow such connections. If a bit is reset, the corresponding Service Category is not supported on the interface, and CAC will reject such connections. Write access may not be supported on all interfaces. Not all Service Categories may be supported on an interface. For example, mixing of Service Categories may not be allowed on a VP tunnel interface. The various bit positions are: 1 constant bit rate (cbr) 2 variable bit rate-real time (vbr-rt) 4 variable bit rate-non real time (vbr-nrt) 8 available bit rate (abr) 16 unspecified bit rate (ubr)" ::= { rmIfCfgEntry 13 } rmIfFramingOverhead OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "If this object is set to true, framing overhead will be taken into account in determining the Maximum Cell Rate that is possible on this interface. If this object is set to false, framing overhead will not figure in the determination of the Maximum Cell Rate that is possible on this interface. If setting the value of this object to true results in reducing the Maximum Guaranteed Services Bandwidth of this interface below the currently allocated bandwidth guarantees on this interface, the object rmIfFramingOverheadForce must also be set in order to cause the change to take effect. This object is not instantiated for interfaces to which it cannot be applied." DEFVAL { false } ::= { rmIfCfgEntry 14 } rmIfFramingOverheadForce OBJECT-TYPE SYNTAX ForceValue MAX-ACCESS read-write STATUS current DESCRIPTION "A Set Request for rmIfFramingOverhead that does not reduce the Maximum Guaranteed Services Bandwidth of this interface below the currently allocated bandwidth guarantees always succeeds irrespective of the value of rmIfFramingOverheadForce. But a Set Request for rmIfFramingOverhead that does reduce the Maximum Guaranteed Services Bandwidth of this interface below the currently allocated bandwidth guarantees will succeed only if rmIfFramingOverheadForce object is also set to the value forceChange. In either of the above cases, once the rmIfFramingOverhead object is set to the appropriate value, rmIfFramingOverheadForce object assumes the noForceChange value. This object is not instantiated for interfaces to which it cannot be applied." DEFVAL { noForceChange } ::= { rmIfCfgEntry 15 } rmIfOverBooking OBJECT-TYPE SYNTAX INTEGER (100..1000) UNITS "percent" MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies overbooking on this interface as a percentage of the Maximum Cell Rate that is possible on this interface. If the value of this object is 100, overbooking is disabled on this interface. A set request for this object will succeed only if the value of the ifAdminStatus object for this interface is 'down'. This object is not instantiated for interfaces to which it cannot be applied." DEFVAL { 100 } ::= { rmIfCfgEntry 16 } rmIfVbrRtPerClassOverbooking OBJECT-TYPE SYNTAX INTEGER (100..3200) UNITS "percent" MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the Per Class Overbooking percentage for VBR-rt service category on this interface. If the value of this object is 100, Per Class Overbooking for VBR-rt is disabled on this interface. Specifying a value that is greater than 100 causes the CAC to scale down the bandwidth allocated to a VBR-rt VC on this interface by a factor that is equal to the inverse of the overbooking percentage specified by this object. A set request for this object will succeed only if the value of the ifAdminStatus object for this interface is 'down' and Interface overbooking (rmIfOverBooking object) is disabled. A set request for this object will not succeed if it specifies a value that would cause the current bandwidth guarantees on this interface to exceed the maximum bandwidth available for guaranteed services on this interface." DEFVAL { 100 } ::= { rmIfCfgEntry 17 } rmIfVbrNrtPerClassOverbooking OBJECT-TYPE SYNTAX INTEGER (100..3200) UNITS "percent" MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the Per Class Overbooking percentage for VBR-Nrt service category on this interface. If the value of this object is 100, Per Class Overbooking for VBR-Nrt is disabled on this interface. Specifying a value that is greater than 100 causes the CAC to scale down the bandwidth allocated to a VBR-Nrt VC on this interface by a factor that is equal to the inverse of the overbooking percentage specified by this object. A set request for this object will succeed only if the value of the ifAdminStatus object for this interface is 'down' and Interface overbooking (rmIfOverBooking object) is disabled. A set request for this object will not succeed if it specifies a value that would cause the current bandwidth guarantees on this interface to exceed the maximum bandwidth available for guaranteed services on this interface." DEFVAL { 100 } ::= { rmIfCfgEntry 18 } rmIfAbrPerClassOverbooking OBJECT-TYPE SYNTAX INTEGER (100..3200) UNITS "percent" MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the Per Class Overbooking percentage for ABR service category on this interface. If the value of this object is 100, Per Class Overbooking for ABR is disabled on this interface. Specifying a value that is greater than 100 causes the CAC to scale down the bandwidth allocated to a ABR VC on this interface by a factor that is equal to the inverse of the overbooking percentage specified by this object. A set request for this object will succeed only if the value of the ifAdminStatus object for this interface is 'down' and Interface overbooking (rmIfOverBooking object) is disabled. A set request for this object will not succeed if it specifies a value that would cause the current bandwidth guarantees on this interface to exceed the maximum bandwidth available for guaranteed services on this interface." DEFVAL { 100 } ::= { rmIfCfgEntry 19 } rmIfUbrPerClassOverbooking OBJECT-TYPE SYNTAX INTEGER (100..3200) UNITS "percent" MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the Per Class Overbooking percentage for UBR service category on this interface. If the value of this object is 100, Per Class Overbooking for UBR is disabled on this interface. Specifying a value that is greater than 100 causes the CAC to scale down the bandwidth allocated to a UBR VC on this interface by a factor that is equal to the inverse of the overbooking percentage specified by this object. A set request for this object will succeed only if the value of the ifAdminStatus object for this interface is 'down' and Interface overbooking (rmIfOverBooking object) is disabled. A set request for this object will not succeed if it specifies a value that would cause the current bandwidth guarantees on this interface to exceed the maximum bandwidth available for guaranteed services on this interface." DEFVAL { 100 } ::= { rmIfCfgEntry 20 } rmIfDirectionCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF RmIfDirectionCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The (conceptual) table containing Resource Management configuration information for a single direction of traffic flow on ATM interfaces." ::= { ciscoAtmRmIfCfg 4 } rmIfDirectionCfgEntry OBJECT-TYPE SYNTAX RmIfDirectionCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in the rmIfInOutCfgTable containing Resource Management configuration for a traffic direction on an ATM interface. The particular interface is identified by the value of MIB-II's ifIndex, and the direction of flow." INDEX { ifIndex, rmIfDirection } ::= { rmIfDirectionCfgTable 1 } RmIfDirectionCfgEntry ::= SEQUENCE { rmIfDirection INTEGER, rmIfDirControlLinkShareMaxAgg INTEGER, rmIfDirControlLinkShareMinCbr INTEGER, rmIfDirControlLinkShareMaxCbr INTEGER, rmIfDirControlLinkShareMinVbr INTEGER, rmIfDirControlLinkShareMaxVbr INTEGER, rmIfDirMaxCbrPcr Unsigned32, rmIfDirMaxCbrTolerance Unsigned32, rmIfDirMaxVbrPcr Unsigned32, rmIfDirMaxVbrScr Unsigned32, rmIfDirMaxVbrTolerance Unsigned32, rmIfDirMaxAbrPcr Unsigned32, rmIfDirMaxAbrTolerance Unsigned32, rmIfDirMaxUbrPcr Unsigned32, rmIfDirMaxUbrTolerance Unsigned32, rmIfDirMaxAbrMcr Unsigned32, rmIfDirMaxUbrMcr Unsigned32, rmIfDirMaxVbrCdvt Unsigned32, rmIfDirControlLinkShareMinAbr INTEGER, rmIfDirControlLinkShareMaxAbr INTEGER, rmIfDirControlLinkShareMinUbr INTEGER, rmIfDirControlLinkShareMaxUbr INTEGER } rmIfDirection OBJECT-TYPE SYNTAX INTEGER { receive(1), transmit(2) } MAX-ACCESS not-accessible STATUS current DESCRIPTION "Selects the traffic direction for which subsequent row parameters are read or written. In is received from the port(into the device), Out is transmitted to the port (from the device)." ::= { rmIfDirectionCfgEntry 1 } rmIfDirControlLinkShareMaxAgg OBJECT-TYPE SYNTAX INTEGER (-1..95) MAX-ACCESS read-write STATUS current DESCRIPTION "Configuration in the Controller Link Sharing (CLS) scheme. Specifies the maximum aggregate Guaranteed Service (CBR or VBR) traffic that can be allocated in a traffic direction on an interface. It is expressed as a percentage of the maximum traffic direction's bandwidth (applies after output pacing, for example). This object interacts with MaxVbr (if specified) such that MaxVbr <= MaxAgg. This object interacts with MaxCbr (if specified) such that MaxCbr <= MaxAgg. This object interacts with MaxAbr (if specified) such that MaxAbr <= MaxAgg. This object interacts with MaxUbr (if specified) such that MaxUbr <= MaxAgg. Note that a change to this value affects subsequent connection setup, not existing connections. If the object is set to -1, the object is considered to be unspecified. This object is not instantiated for interfaces to which it cannot be applied." DEFVAL { -1 } ::= { rmIfDirectionCfgEntry 2 } rmIfDirControlLinkShareMinCbr OBJECT-TYPE SYNTAX INTEGER (-1..95) MAX-ACCESS read-write STATUS current DESCRIPTION "Configuration in the Controller Link Sharing (CLS) scheme. Specifies a minimum amount of CBR traffic that can be reserved in a traffic direction on an interface. It is expressed as a percentage of the maximum traffic direction's bandwidth (applies after output pacing, for example). This object interacts with MinVbr, MinAbr, MinUbr (if specified) such that MinVbr + MinCbr + MinAbr + MinUbr <= 95%. This object interacts with MaxCbr (if specified) such that MinCbr < MaxCbr. Note that a change to this value affects subsequent connection setup, not existing connections. If the object is set to -1, the object is considered to be unspecified. This object is not instantiated for interfaces to which it cannot be applied." DEFVAL { -1 } ::= { rmIfDirectionCfgEntry 3 } rmIfDirControlLinkShareMaxCbr OBJECT-TYPE SYNTAX INTEGER (-1..95) MAX-ACCESS read-write STATUS current DESCRIPTION "Configuration in the Controller Link Sharing (CLS) scheme. Specifies the maximum CBR traffic that can be allocated in a traffic direction on an interface. It is expressed as a percentage of the maximum traffic direction's bandwidth (applies after output pacing, for example). This object interacts with MinCbr (if specified) such that MinCbr <= MaxCbr. This object interacts with MaxAgg (if specified) such that MaxCbr <= MaxAgg. Note that a change to this value affects subsequent connection setup, not existing connections. This object is not instantiated for interfaces to which it cannot be applied." DEFVAL { -1 } ::= { rmIfDirectionCfgEntry 4 } rmIfDirControlLinkShareMinVbr OBJECT-TYPE SYNTAX INTEGER (-1..95) MAX-ACCESS read-write STATUS current DESCRIPTION "Configuration in the Controller Link Sharing (CLS) scheme. Specifies a minimum amount of VBR traffic that can be reserved in a traffic direction on an interface. It is expressed as a percentage of the maximum traffic direction's bandwidth (applies after output pacing, for example). This object interacts with MinCbr, MinAbr, and MinUbr (if specified), such that MinVbr + MinCbr + MinAbr + MinUbr <= 95%. This object interacts with MaxVbr (if specified) such that MinVbr <= MaxVbr. Note that a change to this value affects subsequent connection setup, not existing connections. If the object is set to -1, the object is considered to be unspecified. This object is not instantiated for interfaces to which it cannot be applied." DEFVAL { -1 } ::= { rmIfDirectionCfgEntry 5 } rmIfDirControlLinkShareMaxVbr OBJECT-TYPE SYNTAX INTEGER (-1..95) MAX-ACCESS read-write STATUS current DESCRIPTION "Configuration in the Controller Link Sharing (CLS) scheme. Specifies the maximum VBR traffic that can be allocated in a traffic direction on an interface. It is expressed as a percentage of the maximum traffic direction's bandwidth (applies after output pacing, for example). This object interacts with MinVbr (if specified) such that MinVbr <= MaxVbr. This object interacts with MaxAgg (if specified) such that MaxVbr <= MaxAgg. Note that a change to this value affects subsequent connection setup, not existing connections. If the object is set to -1, the object is considered to be unspecified. This object is not instantiated for interfaces to which it cannot be applied." DEFVAL { -1 } ::= { rmIfDirectionCfgEntry 6 } rmIfDirMaxCbrPcr OBJECT-TYPE SYNTAX Unsigned32 UNITS "cells-per-second" MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the maximum Peak-cell-rate (pcr) traffic parameter that can be specified for CBR connections in a traffic direction on an interface. It is specified in cells-per-second. A value of 4294967295 disables checking of this parameter limit. Note that a change to this value affects subsequent connection setup, not existing connections." DEFVAL { 4294967295 } ::= { rmIfDirectionCfgEntry 7 } rmIfDirMaxCbrTolerance OBJECT-TYPE SYNTAX Unsigned32 UNITS "cell-times" MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the maximum limit parameter used in the GCRA algorithm for traffic policing that can be specified for CBR connections in a traffic direction on an interface. It is specified in cell-times. A value of 4294967295 disables checking of this parameter limit. Note that a change to this value affects subsequent connection setup, not existing connections." DEFVAL { 4294967295 } ::= { rmIfDirectionCfgEntry 8 } rmIfDirMaxVbrPcr OBJECT-TYPE SYNTAX Unsigned32 UNITS "cells-per-second" MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the maximum Peak-cell-rate (pcr) traffic parameter that can be specified for VBR connections in a traffic direction on an interface. It is specified in cells-per-second. A value of 4294967295 disables checking of this parameter limit. Note that a change to this value affects subsequent connection setup, not existing connections." DEFVAL { 4294967295 } ::= { rmIfDirectionCfgEntry 9 } rmIfDirMaxVbrScr OBJECT-TYPE SYNTAX Unsigned32 UNITS "cells-per-second" MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the maximum Sustained-cell-rate (scr) traffic parameter that can be specified for VBR connections in a traffic direction on an interface. It is specified in cells-per-second. A value of 4294967295 disables checking of this parameter limit. Note that a change to this value affects subsequent connection setup, not existing connections." DEFVAL { 4294967295 } ::= { rmIfDirectionCfgEntry 10 } rmIfDirMaxVbrTolerance OBJECT-TYPE SYNTAX Unsigned32 UNITS "cell-times" MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the maximum limit parameter used in the GCRA algorithm for traffic policing that can be specified for VBR connections in a traffic direction on an interface. It is specified in cell-times. A value of 4294967295 disables checking of this parameter limit. Note that a change to this value affects subsequent connection setup, not existing connections." DEFVAL { 4294967295 } ::= { rmIfDirectionCfgEntry 11 } rmIfDirMaxAbrPcr OBJECT-TYPE SYNTAX Unsigned32 UNITS "cells-per-second" MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the maximum Peak-cell-rate (pcr) traffic parameter that can be specified for ABR connections in a traffic direction on an interface. It is specified in cells-per-second. A value of 4294967295 disables checking of this parameter limit. Note that a change to this value affects subsequent connection setup, not existing connections." DEFVAL { 4294967295 } ::= { rmIfDirectionCfgEntry 12 } rmIfDirMaxAbrTolerance OBJECT-TYPE SYNTAX Unsigned32 UNITS "cell-times" MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the maximum limit parameter used in the GCRA algorithm for traffic policing that can be specified for ABR connections in a traffic direction on an interface. It is specified in cell-times. A value of 4294967295 disables checking of this parameter limit. Note that a change to this value affects subsequent connection setup, not existing connections." DEFVAL { 4294967295 } ::= { rmIfDirectionCfgEntry 13 } rmIfDirMaxUbrPcr OBJECT-TYPE SYNTAX Unsigned32 UNITS "cells-per-second" MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the maximum Peak-cell-rate (pcr) traffic parameter that can be specified for UBR connections in a traffic direction on an interface. It is specified in cells-per-second. A value of 4294967295 disables checking of this parameter limit. Note that a change to this value affects subsequent connection setup, not existing connections." DEFVAL { 4294967295 } ::= { rmIfDirectionCfgEntry 14 } rmIfDirMaxUbrTolerance OBJECT-TYPE SYNTAX Unsigned32 UNITS "cell-times" MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the maximum limit parameter used in the GCRA algorithm for traffic policing that can be specified for UBR connections in a traffic direction on an interface. It is specified in cell-times. A value of 4294967295 disables checking of this parameter limit. Note that a change to this value affects subsequent connection setup, not existing connections." DEFVAL { 4294967295 } ::= { rmIfDirectionCfgEntry 15 } rmIfDirMaxAbrMcr OBJECT-TYPE SYNTAX Unsigned32 UNITS "cells-per-second" MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the maximum Minimum-cell-rate (mcr) traffic parameter that can be specified for ABR connections in a traffic direction on an interface. It is specified in cells-per-second. A value of 4294967295 disables checking of this parameter limit. Note that a change to this value affects subsequent connection setup, not existing connections." DEFVAL { 4294967295 } ::= { rmIfDirectionCfgEntry 16 } rmIfDirMaxUbrMcr OBJECT-TYPE SYNTAX Unsigned32 UNITS "cells-per-second" MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the maximum Minimum-cell-rate (mcr) traffic parameter that can be specified for UBR plus (UBR with an mcr guaranteed) connections in a traffic direction on an interface. It is specified in cells-per-second. A value of 4294967295 disables checking of this parameter limit. Note that a change to this value affects subsequent connection setup, not existing connections." DEFVAL { 4294967295 } ::= { rmIfDirectionCfgEntry 17 } rmIfDirMaxVbrCdvt OBJECT-TYPE SYNTAX Unsigned32 UNITS "cell-times" MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the maximum peak-rate CDVT parameter used in the GCRA algorithm for traffic policing that can be specified for VBR connections in a traffic direction on an interface. It is specified in cell-times. A value of 4294967295 disables checking of this parameter limit. Note that a change to this value affects subsequent connection setup, not existing connections." DEFVAL { 4294967295 } ::= { rmIfDirectionCfgEntry 18 } rmIfDirControlLinkShareMinAbr OBJECT-TYPE SYNTAX INTEGER (-1..95) MAX-ACCESS read-write STATUS current DESCRIPTION "Configuration in the Controller Link Sharing (CLS) scheme. Specifies a minimum amount of ABR traffic that can be reserved in a traffic direction on an interface. It is expressed as a percentage of the maximum traffic direction's bandwidth (applies after output pacing, for example). This object interacts with MinVbr, MinCbr, and MinUbr (if specified) such that: MinVbr + MinCbr + MinAbr + MinUbr <= 95%. This object interacts with MaxAbr (if specified) such that MinAbr < MaxAbr. Note that a change to this value affects subsequent connection setup, not existing connections. If the object is set to -1, the object is considered to be unspecified. This object is not instantiated for interfaces to which it cannot be applied." DEFVAL { -1 } ::= { rmIfDirectionCfgEntry 19 } rmIfDirControlLinkShareMaxAbr OBJECT-TYPE SYNTAX INTEGER (-1..95) MAX-ACCESS read-write STATUS current DESCRIPTION "Configuration in the Controller Link Sharing (CLS) scheme. Specifies the maximum ABR traffic that can be allocated in a traffic direction on an interface. It is expressed as a percentage of the maximum traffic direction's bandwidth (applies after output pacing, for example). This object interacts with MinAbr (if specified) such that MinAbr <= MaxAbr. This object interacts with MaxAgg (if specified) such that MaxAbr <= MaxAgg. Note that a change to this value affects subsequent connection setup, not existing connections. If the object is set to -1, the object is considered to be unspecified. This object is not instantiated for interfaces to which it cannot be applied." DEFVAL { -1 } ::= { rmIfDirectionCfgEntry 20 } rmIfDirControlLinkShareMinUbr OBJECT-TYPE SYNTAX INTEGER (-1..95) MAX-ACCESS read-write STATUS current DESCRIPTION "Configuration in the Controller Link Sharing (CLS) scheme. Specifies a minimum amount of UBR plus (UBR with an mcr guaranteed) traffic that can be reserved in a traffic direction on an interface. It is expressed as a percentage of the maximum traffic direction's bandwidth (applies after output pacing, for example). This object interacts with MinVbr, MinCbr, and MinAbr (if specified) such that: MinVbr + MinCbr + MinAbr + MinUbr <= 95%. This object interacts with MaxUbr (if specified) such that MinUbr < MaxUbr. Note that a change to this value affects subsequent connection setup, not existing connections. If the object is set to -1, the object is considered to be unspecified. This object is not instantiated for interfaces to which it cannot be applied." DEFVAL { -1 } ::= { rmIfDirectionCfgEntry 21 } rmIfDirControlLinkShareMaxUbr OBJECT-TYPE SYNTAX INTEGER (-1..95) MAX-ACCESS read-write STATUS current DESCRIPTION "Configuration in the Controller Link Sharing (CLS) scheme. Specifies the maximum UBR plus traffic that can be allocated in a traffic direction on an interface. It is expressed as a percentage of the maximum traffic direction's bandwidth (applies after output pacing, for example). This object interacts with MinUbr (if specified) such that MinUbr <= MaxUbr. This object interacts with MaxAgg (if specified) such that MaxUbr <= MaxAgg. Note that a change to this value affects subsequent connection setup, not existing connections. If the object is set to -1, the object is considered to be unspecified. This object is not instantiated for interfaces to which it cannot be applied." DEFVAL { -1 } ::= { rmIfDirectionCfgEntry 22 } -- -- The ATM Interface Resource Management State Group -- rmIfServiceCategoryStateTable OBJECT-TYPE SYNTAX SEQUENCE OF RmIfServiceCategoryStateEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The (conceptual) table containing Resource Management state information for ATM interfaces by Service Category." ::= { ciscoAtmRmIfState 1 } rmIfServiceCategoryStateEntry OBJECT-TYPE SYNTAX RmIfServiceCategoryStateEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in the rmIfServiceCategoryStateTable containing Resource Management configuration for an ATM interface. Rows are identified by the value of MIB-II's ifIndex, and the Service Category." INDEX { ifIndex, rmIfSc } ::= { rmIfServiceCategoryStateTable 1 } RmIfServiceCategoryStateEntry ::= SEQUENCE { rmIfSc INTEGER, rmIfScRxAcr Gauge32, rmIfScTxAcr Gauge32, rmIfScRxAlcr Gauge32, rmIfScTxAlcr Gauge32, rmIfScNumSvxConns Gauge32, rmIfScNumPvxConns Gauge32, rmIfScTxMaxCtd Gauge32, rmIfScTxP2PeakCdv Gauge32, rmIfScTxClr Gauge32, rmIfScTxClrClp01 Gauge32, rmIfScRxDynBwSvcAcr Gauge32, rmIfScTxDynBwSvcAcr Gauge32 } rmIfSc OBJECT-TYPE SYNTAX INTEGER { cbr(1), --constant-bit-rate vbrRt(2), --variable-bit-rate-real-time vbrNrt(3), --variable-bit-rate-non-real-time abr(4), --available-bit-rate ubr(5) --unspecified-bit-rate } MAX-ACCESS not-accessible STATUS current DESCRIPTION "The Service Category to which the row applies." ::= { rmIfServiceCategoryStateEntry 1 } rmIfScRxAcr OBJECT-TYPE SYNTAX Gauge32 UNITS "cells-per-second" MAX-ACCESS read-only STATUS current DESCRIPTION "The Available Cell Rate (specified in cells per second) for traffic received on the interface for this Service Category. This is the bandwidth available for connections. For CBR and VBR Service Categories, this value decreases as a result of connection setup and increases as a result of connection release. For ABR and UBR Service Categories, this value changes as a result of connection setup and teardown only if non-zero mcr is specified.." ::= { rmIfServiceCategoryStateEntry 2 } rmIfScTxAcr OBJECT-TYPE SYNTAX Gauge32 UNITS "cells-per-second" MAX-ACCESS read-only STATUS current DESCRIPTION "The Available Cell Rate (specified in cells per second) for traffic sent out the interface for this Service Category. This is the bandwidth available for connections. For CBR and VBR Service Categories, this value decreases as a result of connection setup and increases as a result of connection release. For ABR and UBR Service Categories, this value changes as a result of connection setup and teardown only if non-zero mcr is specified." ::= { rmIfServiceCategoryStateEntry 3 } rmIfScRxAlcr OBJECT-TYPE SYNTAX Gauge32 UNITS "cells-per-second" MAX-ACCESS read-only STATUS current DESCRIPTION "The Allocated Cell Rate (specified in cells per second) for traffic received on the interface for this Service Category. This is the bandwidth allocated-to connections. For CBR and VBR Service Categories, this value increases as a result of connection setup and decreases as a result of connection release. For ABR and UBR Service Categories, this value changes as a result of connection setup and teardown only if non-zero mcr is specified." ::= { rmIfServiceCategoryStateEntry 4 } rmIfScTxAlcr OBJECT-TYPE SYNTAX Gauge32 UNITS "cells-per-second" MAX-ACCESS read-only STATUS current DESCRIPTION "The Allocated Cell Rate (specified in cells per second) for traffic sent out the interface for this Service Category. This is the bandwidth allocated-to connections. For Guaranteed Service Categories, this value increases as a result of connection setup and decreases as a result of connection release. For ABR and UBR Service Categories, this value changes as a result of connection setup and teardown only if non-zero mcr is specified." ::= { rmIfServiceCategoryStateEntry 5 } rmIfScNumSvxConns OBJECT-TYPE SYNTAX Gauge32 UNITS "number of connections" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of signalled connections (VC or VP) of this Service Category currently allocated on the interface." ::= { rmIfServiceCategoryStateEntry 6 } rmIfScNumPvxConns OBJECT-TYPE SYNTAX Gauge32 UNITS "number of connections" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of permanent connections (VC or VP) of this Service Category currently allocated on the interface." ::= { rmIfServiceCategoryStateEntry 7 } rmIfScTxMaxCtd OBJECT-TYPE SYNTAX Gauge32 UNITS "microseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum Cell Transfer Delay estimated to be experienced by cells of connections transmitted out this interface of this Service Category. This is estimate does not distinguish between clp0 and clp1 cells. This object is valid for Service Category cbr and vbr-rt. For other Service Categories, the object is not defined." ::= { rmIfServiceCategoryStateEntry 8 } rmIfScTxP2PeakCdv OBJECT-TYPE SYNTAX Gauge32 UNITS "microseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The Peak-to-Peak Cell Delay Variation estimated to be experienced by cells of connections transmitted out this interface of this Service Category. This estimate does not distinguish between clp0 and clp1 cells. This object is valid for Service Categories cbr and vbr-rt. For other Service Categories, the object is not defined." ::= { rmIfServiceCategoryStateEntry 9 } rmIfScTxClr OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The Cell Loss Ratio estimated to be experienced by cells of connections transmitted out this interface of this Service Category. This is an estimate for clp0 cells only. The unit of this object is negative power of ten (so an object value of 8 means 10**(-8)). This object is valid for Service Categories cbr, vbr-rt, and vbr-nrt. For other Service Categories, the object is not defined." ::= { rmIfServiceCategoryStateEntry 10 } rmIfScTxClrClp01 OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The Cell Loss Ratio estimated to be experienced by cells of connections transmitted out this interface of this Service Category. This is an estimate for clp0+1 cells. The unit of this object is negative power of ten (so an object value of 8 means 10**(-8)). This object is valid for Service Categories cbr, vbr-rt, and vbr-nrt. For other Service Categories, the object is not defined." ::= { rmIfServiceCategoryStateEntry 11 } rmIfScRxDynBwSvcAcr OBJECT-TYPE SYNTAX Gauge32 UNITS "cells-per-second" MAX-ACCESS read-only STATUS current DESCRIPTION "The Available Cell Rate (specified in cells per second) for traffic received on the interface for this Service Category. This object is valid only for IMA physical interfaces. This is the bandwidth available for SVC connections. For CBR and VBR Service Categories, this value decreases as a result of connection setup and increases as a result of connection release. For ABR and UBR Service Categories, this value changes as a result of connection setup and teardown only if non-zero mcr is specified" ::= { rmIfServiceCategoryStateEntry 12 } rmIfScTxDynBwSvcAcr OBJECT-TYPE SYNTAX Gauge32 UNITS "cells-per-second" MAX-ACCESS read-only STATUS current DESCRIPTION "The Available Cell Rate (specified in cells per second) for traffic transmitted on the interface for this Service Category. This object is valid only for IMA physical interfaces. This is the bandwidth available for SVC connections on physical interfaces. For CBR and VBR Service Categories, this value decreases as a result of connection setup and increases as a result of connection release. For ABR and UBR Service Categories, this value changes as a result of connection setup and teardown only if non-zero mcr is specified" ::= { rmIfServiceCategoryStateEntry 13 } -- -- The ATM Interface Resource Management Statistics Group -- rmIfServiceCategoryStatisticsTable OBJECT-TYPE SYNTAX SEQUENCE OF RmIfServiceCategoryStatisticsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The (conceptual) table containing Resource Management statistics information for ATM interfaces by Service Category." ::= { ciscoAtmRmIfStatistics 1 } rmIfServiceCategoryStatisticsEntry OBJECT-TYPE SYNTAX RmIfServiceCategoryStatisticsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in the rmIfServiceCategoryStatisticsTable containing Resource Management configuration for an ATM interface. Rows are identified by the value of MIB-II's ifIndex, and the Service Category." INDEX { ifIndex, rmIfSc } ::= { rmIfServiceCategoryStatisticsTable 1 } RmIfServiceCategoryStatisticsEntry ::= SEQUENCE { rmIfScRcacResultNumAdmit Counter32, rmIfScRcacResultNumTotalRequests Counter32, rmIfScRcacResultNumFailTraffComb Counter32, rmIfScRcacResultNumFailBw Counter32, rmIfScRcacResultNumFailLoss Counter32, rmIfScRcacResultNumFailDelay Counter32, rmIfScRcacResultNumFailCdv Counter32, rmIfScRcacResultNumFailBeLimit Counter32, rmIfScRcacResultNumFailParmLimit Counter32, rmIfScRcacResultNumFailOther Counter32 } rmIfScRcacResultNumAdmit OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of successful resource allocation requests for this interface." ::= { rmIfServiceCategoryStatisticsEntry 1 } rmIfScRcacResultNumTotalRequests OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of resource allocation requests for this interface." ::= { rmIfServiceCategoryStatisticsEntry 2 } rmIfScRcacResultNumFailTraffComb OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of resource allocation requests which are considered to be in error due to an unsupported combination of traffic parameters. An example of this would be, for a VBR connection, a zero maximum burst-size given a non-zero sustainable-cell-rate." ::= { rmIfServiceCategoryStatisticsEntry 3 } rmIfScRcacResultNumFailBw OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of resource allocation requests which are considered to be in error due to a lack of bandwidth. This will never occur for Best Effort Service Categories." ::= { rmIfServiceCategoryStatisticsEntry 4 } rmIfScRcacResultNumFailLoss OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of resource allocation requests which are considered to be in error due to exceeding cell loss criterion." ::= { rmIfServiceCategoryStatisticsEntry 5 } rmIfScRcacResultNumFailDelay OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of resource allocation requests which are considered to be in error due to exceeding maximum delay criterion." ::= { rmIfServiceCategoryStatisticsEntry 6 } rmIfScRcacResultNumFailCdv OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of resource allocation requests which are considered to be in error due to exceeding cell delay variation criterion." ::= { rmIfServiceCategoryStatisticsEntry 7 } rmIfScRcacResultNumFailBeLimit OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of resource allocation requests which are considered to be in error due to exceeding a limit on the number of Best-Effort connections." ::= { rmIfServiceCategoryStatisticsEntry 8 } rmIfScRcacResultNumFailParmLimit OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of resource allocation requests which are considered to be in error due to exceeding a traffic parameter limit criterion." ::= { rmIfServiceCategoryStatisticsEntry 9 } rmIfScRcacResultNumFailOther OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of resource allocation requests which are considered to be in error for a reason not enumerated by other counter objects." ::= { rmIfServiceCategoryStatisticsEntry 10 } -- -- The Shared-Memory architecture ATM Interface Resource Management Group -- sharedMemRmIfOutputQCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF SharedMemRmIfOutputQCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The (conceptual) table containing configuration information for ATM physical interface output queues. This table is not instantiated for interfaces to which it cannot be applied." ::= { ciscoAtmRmIfSharedMem 1 } sharedMemRmIfOutputQCfgEntry OBJECT-TYPE SYNTAX SharedMemRmIfOutputQCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in the sharedMemRmIfOutputQCfgTable containing Resource Management configuration for an ATM interface. A particular row is identified by the value of MIB-II's ifIndex, and the output queue." INDEX { ifIndex, sharedMemRmIfOutputQ } ::= { sharedMemRmIfOutputQCfgTable 1 } SharedMemRmIfOutputQCfgEntry ::= SEQUENCE { sharedMemRmIfOutputQ INTEGER, sharedMemRmIfOutputQServCategory INTEGER, sharedMemRmIfOutputQRequestedMaxSize INTEGER, sharedMemRmIfOutputQInstalledMaxSize INTEGER, sharedMemRmIfOutputQMaxSizeForce ForceValue, sharedMemRmIfOutputQCellCount Gauge32 } sharedMemRmIfOutputQ OBJECT-TYPE SYNTAX INTEGER { q1(1), -- Priority 1 queue (highest priority) q2(2), -- Priority 2 queue (2nd highest priority) q3(3), -- Priority 3 queue (3rd highest priority) q4(4) -- Priority 4 queue (lowest priority) } MAX-ACCESS not-accessible STATUS current DESCRIPTION "The output queue on this ATM interface." ::= { sharedMemRmIfOutputQCfgEntry 1 } sharedMemRmIfOutputQServCategory OBJECT-TYPE SYNTAX INTEGER (1..31) MAX-ACCESS read-only STATUS current DESCRIPTION "The service category(s) sharing this output queue on this ATM interface. The various bit positions are: 1 constant bit rate (cbr) 2 variable bit rate-real time (vbr-rt) 4 variable bit rate-non real time (vbr-nrt) 8 available bit rate (abr) 16 unspecified bit rate (ubr)" ::= { sharedMemRmIfOutputQCfgEntry 2 } sharedMemRmIfOutputQRequestedMaxSize OBJECT-TYPE SYNTAX INTEGER (0..65504) UNITS "cells" MAX-ACCESS read-write STATUS current DESCRIPTION "This object reflects an explicit configuration of the maximum number of cells that may occupy this queue. If the value of this object is 0, the maximum size in effect is a default value calculated by software. Prior to any user configuration, the value of this object is 0. The actual maximum size is reflected in the object sharedMemRmIfOutputQInstalledMaxSize (and is a default value calculated by software). Setting this value to 0 causes the size to assume it's default value. When changing a port that is up, must be set in conjunction with the force object (sharedMemRmIfOutputQMaxSizeForce) to take effect." DEFVAL { 0 } ::= { sharedMemRmIfOutputQCfgEntry 3 } sharedMemRmIfOutputQInstalledMaxSize OBJECT-TYPE SYNTAX INTEGER (32..65504) UNITS "cells" MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of cells that may occupy this queue. Will be a multiple of 32. Explicit configuration of maximum size are made via the object sharedMemrmIfOutputQRequestedMaxSize. Such requests are rounded up to the nearest multiple of 32 prior to installation." ::= { sharedMemRmIfOutputQCfgEntry 4 } sharedMemRmIfOutputQMaxSizeForce OBJECT-TYPE SYNTAX ForceValue MAX-ACCESS read-write STATUS current DESCRIPTION "Must be set to forceChange to allow changing of sharedMemRmIfOutputQRequestedMaxSize for a queue on an interface that is 'up'. This is because such a change causes the interface to lose data while the size is changed. Once the change takes place, the force object assumes the noForceChange value." DEFVAL { noForceChange } ::= { sharedMemRmIfOutputQCfgEntry 5 } sharedMemRmIfOutputQCellCount OBJECT-TYPE SYNTAX Gauge32 UNITS "cells" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of the number of cells in the output queue." ::= { sharedMemRmIfOutputQCfgEntry 6 } sharedMemRmIfThresholdCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF SharedMemRmIfThresholdCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The (conceptual) table containing the output queue thresholds used on ATM physical interface output queues. These are specified per Service Category. This table is not instantiated for interfaces to which it cannot be applied." ::= { ciscoAtmRmIfSharedMem 2 } sharedMemRmIfThresholdCfgEntry OBJECT-TYPE SYNTAX SharedMemRmIfThresholdCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in the sharedMemRmIfThresholdCfgTable containing Resource Management configuration for an ATM interface. A particular row is identified by the value of MIB-II's ifIndex, and the Service Category." INDEX { ifIndex, rmIfSc} ::= { sharedMemRmIfThresholdCfgTable 1 } SharedMemRmIfThresholdCfgEntry ::= SEQUENCE { sharedMemRmIfDiscardThreshold FineQueueThreshold, sharedMemRmIfEfciThreshold INTEGER, sharedMemRmIfAbrRelativeRateThreshold FineQueueThreshold } sharedMemRmIfDiscardThreshold OBJECT-TYPE SYNTAX FineQueueThreshold MAX-ACCESS read-write STATUS current DESCRIPTION "The output queue CLP/EPD threshold for this Service Category on this ATM interface. This is expressed in percent-of-full. Note that 100% full effectively turns off the threshold." DEFVAL { percent50 } ::= { sharedMemRmIfThresholdCfgEntry 1 } sharedMemRmIfEfciThreshold OBJECT-TYPE SYNTAX INTEGER { percent12(1), percent25(2), percent50(3), percent100(4) } MAX-ACCESS read-write STATUS current DESCRIPTION "The output queue EFCI marking threshold for this Service Category on this ATM interface. This is expressed in percent-of-full. Note that 100% full effectively turns off the threshold." DEFVAL { percent25 } ::= { sharedMemRmIfThresholdCfgEntry 2 } sharedMemRmIfAbrRelativeRateThreshold OBJECT-TYPE SYNTAX FineQueueThreshold MAX-ACCESS read-write STATUS current DESCRIPTION "The ABR Relative-rate marking queue congestion threshold for the ABR queue on this ATM interface. This is expressed in percent-of-full. Note that 100% full effectively turns off the threshold. This object is only defined for the abr service category." DEFVAL { percent25 } ::= { sharedMemRmIfThresholdCfgEntry 3 } -- -- The Lightstream per-VC queueing chipset ATM Switch Resource -- Management Group -- lsPerVcqRmThreshGrpTable OBJECT-TYPE SYNTAX SEQUENCE OF LsPerVcqRmThreshGrpEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The (conceptual) table containing information for Switch Threshold Groups. When cells are queued in the switch for a direction of cell traffic on an ATM connection (VC or VP), several functions related to queueing are dictated by the congestion state (fullness) of the Threshold Group. Each connection queue is a member of a Threshold Group. These functions include: - The limit on the number of cells that can be queued. Cells exceeding this limit are discarded. - The discard threshold, used for CLP/EPD discard when the fullness of the queue exceeds the threshold. - The marking threshold, used for EFCI and ABR-RR marking. Each Threshold Group has a maximum number of cells that can be resident in it at any one time. The number of cells in a Group consists of the number of cells in all the queues that are a member of the Group. As the number of cells in a Group approaches the maximum number for the Group, the queue limits may be decreased. This limits the share of buffering available to each connection as cell-memory is used." ::= { ciscoLsPerVcqAtmRmSwitch 1 } lsPerVcqRmThreshGrpEntry OBJECT-TYPE SYNTAX LsPerVcqRmThreshGrpEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in the lsPerVcqRmThreshGrpTable containing Resource Management configuration for a Threshold Group. All entries ever in the table are present at startup, none are created dynamically." INDEX { lsPerVcqRmThreshGrp } ::= { lsPerVcqRmThreshGrpTable 1 } LsPerVcqRmThreshGrpEntry ::= SEQUENCE { lsPerVcqRmThreshGrp LsPerVcqThresholdGroup, lsPerVcqRmThreshGrpMaxSize INTEGER, lsPerVcqRmThreshGrpQMaxSize INTEGER, lsPerVcqRmThreshGrpQMinSize INTEGER, lsPerVcqRmThreshGrpDiscThreshold INTEGER, lsPerVcqRmThreshGrpMarkThreshold INTEGER, lsPerVcqRmThreshGrpName DisplayString, lsPerVcqRmThreshGrpCellCount Gauge32 } lsPerVcqRmThreshGrp OBJECT-TYPE SYNTAX LsPerVcqThresholdGroup MAX-ACCESS not-accessible STATUS current DESCRIPTION "The Threshold Group specified by this entry." ::= { lsPerVcqRmThreshGrpEntry 1 } lsPerVcqRmThreshGrpMaxSize OBJECT-TYPE SYNTAX INTEGER (-1..65535) UNITS "cells" MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the maximum number of cells that may occupy this Threshold Group. While any integer in the range can be set, the hardware granularity is in 64-cell units. Therefore, the value installed is [(value / 64) * 64] + 63. If the value of this object is set to -1, the default value for the threshold-group is restored." DEFVAL { 65535 } ::= { lsPerVcqRmThreshGrpEntry 2 } lsPerVcqRmThreshGrpQMaxSize OBJECT-TYPE SYNTAX INTEGER (31..16383) UNITS "cells" MAX-ACCESS read-write STATUS current DESCRIPTION "This object reflects an explicit configuration of the maximum limit on the number of cells that may occupy connection queues that are a member of this Threshold Group. A connection queue that is a member of this Threshold Group will never have more cells resident in it than this limit. This is the queue limit applied when the Threshold Group is uncongested. The QMaxSize must be greater than or equal to the Threshold Group QMinSize. QMaxSize should be less than MaxSize for the Threshold Group. While any integer in the range can be set, the hardware granularity is in 16-cell units. Therefore, the largest possible queue size installed is: [(value / 16) * 16]+15" ::= { lsPerVcqRmThreshGrpEntry 3 } lsPerVcqRmThreshGrpQMinSize OBJECT-TYPE SYNTAX INTEGER (1..1023) UNITS "cells" MAX-ACCESS read-write STATUS current DESCRIPTION "This object reflects an explicit configuration of the minimum limit on the number of cells that may occupy connection queues that are a member of this Threshold Group. The Threshold Group at it's most congested will not limit a connection queue to fewer than this number of cells. The QMinSize must be less than or equal to the Threshold Group QMaxSize. The hardware granularity is in units of one cell." ::= { lsPerVcqRmThreshGrpEntry 4 } lsPerVcqRmThreshGrpDiscThreshold OBJECT-TYPE SYNTAX INTEGER (-1..100) UNITS "percentage" MAX-ACCESS read-write STATUS current DESCRIPTION "The output queue CLP/EPD threshold for this Threshold Group. This is expressed in percent-of-full. Note that 100% full effectively turns off the threshold. Setting this object to -1 restores the default value for the Threshold Group. The granularity of the fill-level of a queue installed in hardware is the same as that for queue limits." ::= { lsPerVcqRmThreshGrpEntry 5 } lsPerVcqRmThreshGrpMarkThreshold OBJECT-TYPE SYNTAX INTEGER (-1..100) UNITS "percentage" MAX-ACCESS read-write STATUS current DESCRIPTION "The output queue EFCI/ABR-RR marking threshold for this Threshold Group. This is expressed in percent-of-full. Note that 100% full effectively turns off the threshold. Setting this object to -1 restores the default value for the Threshold Group. The granularity of the fill-level of a queue installed in hardware is the same as that for queue limits." ::= { lsPerVcqRmThreshGrpEntry 6 } lsPerVcqRmThreshGrpName OBJECT-TYPE SYNTAX DisplayString (SIZE (0..20)) MAX-ACCESS read-write STATUS current DESCRIPTION "The name associated with the threshold-group. If this is set to the null-string, the default name for the Threshold Group is assigned." ::= { lsPerVcqRmThreshGrpEntry 7 } lsPerVcqRmThreshGrpCellCount OBJECT-TYPE SYNTAX Gauge32 UNITS "cells" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of the number of cells in the Threshold Group." ::= { lsPerVcqRmThreshGrpEntry 8 } lsPerVcqRmThreshGrpServiceTable OBJECT-TYPE SYNTAX SEQUENCE OF LsPerVcqRmThreshGrpServiceEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The (conceptual) table specifying which VC or VP queues are assigned to a Threshold Group." ::= { ciscoLsPerVcqAtmRmSwitch 2 } lsPerVcqRmThreshGrpServiceEntry OBJECT-TYPE SYNTAX LsPerVcqRmThreshGrpServiceEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in the lsPerVcqRmThreshGrpServiceTable. All entries ever in the table are present at startup, none are created dynamically." INDEX { lsPerVcqRmThreshGrpService } ::= { lsPerVcqRmThreshGrpServiceTable 1 } LsPerVcqRmThreshGrpServiceEntry ::= SEQUENCE { lsPerVcqRmThreshGrpService LsPerVcqThresholdGroupService, lsPerVcqRmThreshGrpServGroup LsPerVcqThresholdGroup } lsPerVcqRmThreshGrpService OBJECT-TYPE SYNTAX LsPerVcqThresholdGroupService MAX-ACCESS not-accessible STATUS current DESCRIPTION "The Service specified by this entry." ::= { lsPerVcqRmThreshGrpServiceEntry 1 } lsPerVcqRmThreshGrpServGroup OBJECT-TYPE SYNTAX LsPerVcqThresholdGroup MAX-ACCESS read-write STATUS current DESCRIPTION "The Threshold Group to which VC/VP queues specified by the service are assigned. Changing the assignment of service to Threshold Group does not alter the assignment for connections currently installed in hardware, but those connections that are subsequently installed." ::= { lsPerVcqRmThreshGrpServiceEntry 2 } lsPerVcqRmHierarchicalSchedulingMode OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "On a LS1010 equipped with the Lightstream per-VC queueing chipset, the user can define Hierarchical VP-Tunnels. Each such tunnel has its own dedicated scheduler, programmed to output data at a configurable maximum rate. Therefore, the overall output of the Hierarchical VP-tunnel is rate-limited. In addition, Virtual Circuits of different service categories can traverse through such a tunnel, and each of these Virtual Circuits are guaranteed their individual contracted bandwidth agreement. This object must be set to enabled before any Hierarchical VP-tunnels can be defined on the device. Any setting of this variable requires a reload of the device to be effective. Setting this object to enabled will cause the software to initialize the additional schedulers needed by the Hierarchical VP-Tunnels. Other limited scheduler resources are therefore used by a larger number of schedulers (as compared to the case when Hierarchical Scheduling is disabled on the device). This may result in fewer number of connections passing Connection Admission Control. This object is therefore provided so that the user can make an informed decision as to whether Hierarchical Scheduling is to be used. This object is defined on a LS1010 only when the switch is equipped with the Lightstream per-VC queueing chipset." DEFVAL { disabled } ::= { ciscoLsPerVcqAtmRmSwitch 3 } -- -- The Catalyst8540MSR per-VC queueing chipset ATM Switch Resource -- Management Group -- cgrPerVcqRmThreshGrpTable OBJECT-TYPE SYNTAX SEQUENCE OF CgrPerVcqRmThreshGrpEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The (conceptual) table containing information for Switch Threshold Groups. When cells are queued in the switch for a direction of cell traffic on an ATM connection (VC or VP), several functions related to queueing are dictated by the congestion state (fullness) of the Threshold Group. Each connection queue is a member of a Threshold Group. These functions include: - The limit on the number of cells that can be queued. Cells exceeding this limit are discarded. - The discard threshold, used for CLP/EPD discard when the fullness of the queue exceeds the threshold. - The marking threshold, used for EFCI marking. Each Threshold Group has a maximum number of cells that can be resident in it at any one time. The number of cells in a Group consists of the number of cells in all the queues that are a member of the Group. As the number of cells in a Group approaches the maximum number for the Group, the queue limits may be decreased. This limits the share of buffering available to each connection as cell-memory is used. On the Catalyst8540MSR platform, there are a maximum of 8 switching modules. Each switching module services a certain group of ports (this mapping is fixed in hardware). Each module also has its own cell memory (for per VC queueing), and hence performs its own congestion control, independent of any other switching module. Each switching module has its own set of Switch Threshold Groups, which are independently programmable and readable. This table is supported only on the Catalyst8540MSR platform." ::= { ciscoCgrPerVcqAtmRmSwitch 1 } cgrPerVcqRmThreshGrpEntry OBJECT-TYPE SYNTAX CgrPerVcqRmThreshGrpEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in the cgrPerVcqRmThreshGrpTable containing Resource Management configuration for a Threshold Group. All entries ever in the table are present at startup, none are created dynamically." INDEX { cgrPerVcqModuleId, cgrPerVcqRmThreshGrp } ::= { cgrPerVcqRmThreshGrpTable 1 } CgrPerVcqRmThreshGrpEntry ::= SEQUENCE { cgrPerVcqModuleId CgrPerVcqModuleId, cgrPerVcqRmThreshGrp LsPerVcqThresholdGroup, cgrPerVcqRmThreshGrpMaxSize INTEGER, cgrPerVcqRmThreshGrpQMaxSize INTEGER, cgrPerVcqRmThreshGrpQMinSize INTEGER, cgrPerVcqRmThreshGrpDiscThreshold INTEGER, cgrPerVcqRmThreshGrpMarkThreshold INTEGER, cgrPerVcqRmThreshGrpName DisplayString, cgrPerVcqRmThreshGrpCellCount Gauge32 } cgrPerVcqModuleId OBJECT-TYPE SYNTAX CgrPerVcqModuleId MAX-ACCESS not-accessible STATUS current DESCRIPTION "The switching module specified by this entry." ::= { cgrPerVcqRmThreshGrpEntry 1 } cgrPerVcqRmThreshGrp OBJECT-TYPE SYNTAX LsPerVcqThresholdGroup MAX-ACCESS not-accessible STATUS current DESCRIPTION "The Threshold Group specified by this entry." ::= { cgrPerVcqRmThreshGrpEntry 2 } cgrPerVcqRmThreshGrpMaxSize OBJECT-TYPE SYNTAX INTEGER (-1..131071) UNITS "cells" MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the maximum number of cells that may occupy this Threshold Group. While any integer in the range can be set, the hardware granularity is in 64-cell units. Therefore, the value installed is [(value / 64) * 64] + 63. Even though the maximum value for this object is 131071, the cell memory actually present in hardware can be less. The agent will allow values for this object not exceeding the actual cell memory present in hardware. If the value of this object is set to -1, the default value for the threshold-group is restored." DEFVAL { 131071 } ::= { cgrPerVcqRmThreshGrpEntry 3 } cgrPerVcqRmThreshGrpQMaxSize OBJECT-TYPE SYNTAX INTEGER (31..16383) UNITS "cells" MAX-ACCESS read-write STATUS current DESCRIPTION "This object reflects an explicit configuration of the maximum limit on the number of cells that may occupy connection queues that are a member of this Threshold Group. A connection queue that is a member of this Threshold Group will never have more cells resident in it than this limit. This is the queue limit applied when the Threshold Group is uncongested. The QMaxSize must be greater than or equal to the Threshold Group QMinSize. QMaxSize should be less than MaxSize for the Threshold Group. While any integer in the range can be set, the hardware granularity is in 16-cell units. Therefore, the largest possible queue size installed is: [(value / 16) * 16]+15" ::= { cgrPerVcqRmThreshGrpEntry 4 } cgrPerVcqRmThreshGrpQMinSize OBJECT-TYPE SYNTAX INTEGER (1..1023) UNITS "cells" MAX-ACCESS read-write STATUS current DESCRIPTION "This object reflects an explicit configuration of the minimum limit on the number of cells that may occupy connection queues that are a member of this Threshold Group. The Threshold Group at it's most congested will not limit a connection queue to fewer than this number of cells. The QMinSize must be less than or equal to the Threshold Group QMaxSize. The hardware granularity is in units of one cell." ::= { cgrPerVcqRmThreshGrpEntry 5 } cgrPerVcqRmThreshGrpDiscThreshold OBJECT-TYPE SYNTAX INTEGER (-1..100) UNITS "percentage" MAX-ACCESS read-write STATUS current DESCRIPTION "The output queue CLP/EPD threshold for this Threshold Group. This is expressed in percent-of-full. Note that 100% full effectively turns off the threshold. Setting this object to -1 restores the default value for the Threshold Group. The granularity of the fill-level of a queue installed in hardware is the same as that for queue limits." ::= { cgrPerVcqRmThreshGrpEntry 6 } cgrPerVcqRmThreshGrpMarkThreshold OBJECT-TYPE SYNTAX INTEGER (-1..100) UNITS "percentage" MAX-ACCESS read-write STATUS current DESCRIPTION "The output queue EFCI/ABR-RR marking threshold for this Threshold Group. This is expressed in percent-of-full. Note that 100% full effectively turns off the threshold. Setting this object to -1 restores the default value for the Threshold Group. The granularity of the fill-level of a queue installed in hardware is the same as that for queue limits." ::= { cgrPerVcqRmThreshGrpEntry 7 } cgrPerVcqRmThreshGrpName OBJECT-TYPE SYNTAX DisplayString (SIZE (0..20)) MAX-ACCESS read-write STATUS current DESCRIPTION "The name associated with the threshold-group. If this is set to the null-string, the default name for the Threshold Group is assigned." ::= { cgrPerVcqRmThreshGrpEntry 8 } cgrPerVcqRmThreshGrpCellCount OBJECT-TYPE SYNTAX Gauge32 UNITS "cells" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of the number of cells in the Threshold Group." ::= { cgrPerVcqRmThreshGrpEntry 9 } cgrPerVcqRmThreshGrpServiceTable OBJECT-TYPE SYNTAX SEQUENCE OF CgrPerVcqRmThreshGrpServiceEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The (conceptual) table specifying which VC or VP queues are assigned to a Threshold Group. This table is supported only on the Catalyst8540MSR Platform." ::= { ciscoCgrPerVcqAtmRmSwitch 2 } cgrPerVcqRmThreshGrpServiceEntry OBJECT-TYPE SYNTAX CgrPerVcqRmThreshGrpServiceEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in the cgrPerVcqRmThreshGrpServiceTable. All entries ever in the table are present at startup, none are created dynamically." INDEX { cgrPerVcqRmThreshGrpService } ::= { cgrPerVcqRmThreshGrpServiceTable 1 } CgrPerVcqRmThreshGrpServiceEntry ::= SEQUENCE { cgrPerVcqRmThreshGrpService LsPerVcqThresholdGroupService, cgrPerVcqRmThreshGrpServGroup LsPerVcqThresholdGroup } cgrPerVcqRmThreshGrpService OBJECT-TYPE SYNTAX LsPerVcqThresholdGroupService MAX-ACCESS not-accessible STATUS current DESCRIPTION "The Service specified by this entry." ::= { cgrPerVcqRmThreshGrpServiceEntry 1 } cgrPerVcqRmThreshGrpServGroup OBJECT-TYPE SYNTAX LsPerVcqThresholdGroup MAX-ACCESS read-write STATUS current DESCRIPTION "The Threshold Group to which VC/VP queues specified by the service are assigned. Changing the assignment of service to Threshold Group does not alter the assignment for connections currently installed in hardware, but those connections that are subsequently installed." ::= { cgrPerVcqRmThreshGrpServiceEntry 2 } cgrPerVcqRmHierarchicalSchedulingMode OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "On a Catalyst8540 MSR, the user can define Hierarchical VP-Tunnels. Each such tunnel has its own dedicated scheduler, programmed to output data at a configurable maximum rate. Therefore, the overall output of the Hierarchical VP-tunnel is rate-limited. In addition, Virtual Circuits of different service categories can traverse through such a tunnel, and each of these Virtual Circuits are guaranteed their individual contracted bandwidth agreement. This object must be set to enabled before any Hierarchical VP-tunnels can be defined on the device. Any setting of this variable requires a reload of the device to be effective. Setting this object to enabled will cause the software to initialize the additional schedulers needed by the Hierarchical VP-Tunnels. Other limited scheduler resources are therefore used by a larger number of schedulers (as compared to the case when Hierarchical Scheduling is disabled on the device). This may result in fewer number of connections passing Connection Admission Control. This object is therefore provided so that the user can make an informed decision as to whether Hierarchical Scheduling is to be used. This object is supported only on the Catalyst8540MSR platform." DEFVAL { disabled } ::= { ciscoCgrPerVcqAtmRmSwitch 3 } -- -- The Lightstream per-VC queueing switch chipset ATM Interface Resource -- Management Group -- lsPerVcqRmIfTable OBJECT-TYPE SYNTAX SEQUENCE OF LsPerVcqRmIfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The (conceptual) table containing configuration information for ATM physical interfaces." ::= { ciscoLsPerVcqAtmRmIf 1 } lsPerVcqRmIfEntry OBJECT-TYPE SYNTAX LsPerVcqRmIfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in the lsPerVcqRmIfTable containing Resource Management configuration for an ATM interface. An entry in the table is present when an entry in the ifTable is created for an ATM interface that uses the Lighstream per-VC queueing chipset." INDEX { ifIndex } ::= { lsPerVcqRmIfTable 1 } LsPerVcqRmIfEntry ::= SEQUENCE { lsPerVcqRmIfMinWrrServiceClass LsPerVcqServiceClass } lsPerVcqRmIfMinWrrServiceClass OBJECT-TYPE SYNTAX LsPerVcqServiceClass UNITS "service class" MAX-ACCESS read-write STATUS current DESCRIPTION "The service classes on an interface are partitioned into two subsets, dictating how a service class with a cell ready to transmit is chosen (subsequently a connection is chosen within the selected service class). There are two subsets: Strict Priority (SP), and Weighted Round Robin (WRR). The SP subset service classes are selected by strict priority (highest priority with available cell wins). If there are any SP service classes, they take precedence over any WRR classes. A WRR subset service class is chosen from among the WRR service classes with an available cell using a WRR algorithm. The SP service classes (if any) include a contiguous range of classes, starting with c2 (c1 is dedicated to CBR, which doesn't use SP/WRR). The WRR service classes (if any) include a contiguous range of classes, ending with c5. This object specifies the break-point between SP and WRR service classes. Note that (assuming all service classes are used) specifying c2 indicates all service classes are WRR, and specifying c5 indicates all service classes are SP." ::= { lsPerVcqRmIfEntry 1 } lsPerVcqRmIfServiceClassTable OBJECT-TYPE SYNTAX SEQUENCE OF LsPerVcqRmIfServiceClassEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The (conceptual) table containing configuration information for ATM physical interface Service Classes (not logical port ATM interfaces). An ATM connection (VC or VP) on an interface is a member of a Service Class. The Service Class is used in the scheduling discipline that determines which cell is next transmitted on the interface. If the rate scheduler has no cell to be sent in the guaranteed cell-flow on an interface, a decision is made between all Service Classes with VCs with cells ready for transmit." ::= { ciscoLsPerVcqAtmRmIf 2 } lsPerVcqRmIfServiceClassEntry OBJECT-TYPE SYNTAX LsPerVcqRmIfServiceClassEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in the lsPerVcqRmIfServiceClassTable containing Resource Management configuration for an ATM interface. A particular row is identified by the value of MIB-II's ifIndex, and the output queue. An entry in the table is present when an entry in the ifTable is created for an ATM interface that uses the Lighstream per-VC queueing chipset." INDEX { ifIndex, lsPerVcqRmIfServiceClass } ::= { lsPerVcqRmIfServiceClassTable 1 } LsPerVcqRmIfServiceClassEntry ::= SEQUENCE { lsPerVcqRmIfServiceClass LsPerVcqServiceClass, lsPerVcqRmIfServClassConnType INTEGER, lsPerVcqRmIfServClassWrrWeight INTEGER } lsPerVcqRmIfServiceClass OBJECT-TYPE SYNTAX LsPerVcqServiceClass MAX-ACCESS not-accessible STATUS current DESCRIPTION "The service class on this ATM interface." ::= { lsPerVcqRmIfServiceClassEntry 1 } lsPerVcqRmIfServClassConnType OBJECT-TYPE SYNTAX INTEGER (1..31) MAX-ACCESS read-only STATUS current DESCRIPTION "The types of connections using this service class on this ATM interface. The various bit positions are: 1 constant bit rate (cbr) 2 variable bit rate-real time (vbr-rt) 4 variable bit rate-non real time (vbr-nrt) 8 available bit rate (abr) 16 unspecified bit rate (ubr)" ::= { lsPerVcqRmIfServiceClassEntry 2 } lsPerVcqRmIfServClassWrrWeight OBJECT-TYPE SYNTAX INTEGER (1..15) UNITS "weight" MAX-ACCESS read-write STATUS current DESCRIPTION "Configure the weighting specified for a service class to make the scheduling decision among active service classes in the WRR subset." ::= { lsPerVcqRmIfServiceClassEntry 3 } -- -- The ATM Resource Management Traffic Shaper Interface Objects -- rmTrafficShaperIfTable OBJECT-TYPE SYNTAX SEQUENCE OF RmTrafficShaperIfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The (conceptual) table containing ATM Traffic Shaper configuration and state information for ATM interfaces." ::= { ciscoAtmRmTrafShaperIf 1 } rmTrafficShaperIfEntry OBJECT-TYPE SYNTAX RmTrafficShaperIfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in the rmTrafficShaperIfTable containing Traffic Shaper configuration and state information for an ATM interface. The particular interface is identified by the value of MIB-II's ifIndex." INDEX { ifIndex } ::= { rmTrafficShaperIfTable 1 } RmTrafficShaperIfEntry ::= SEQUENCE { rtsIfMaxThreshold Unsigned32, rtsIfCellCount Gauge32, rtsIfVbrCfgRequested INTEGER, rtsIfVbrCfgInstalled INTEGER, rtsIfBeCfgRequested INTEGER, rtsIfBeCfgInstalled INTEGER, rtsIfVbrClassMaxThrshRequested INTEGER, rtsIfVbrClassMaxThrshInstalled Unsigned32, rtsIfBeClassMaxThrshRequested INTEGER, rtsIfBeClassMaxThrshInstalled Unsigned32, rtsIfVbrVcMaxThrshRequested Unsigned32, rtsIfVbrVcMaxThrshInstalled Unsigned32, rtsIfBeVcMaxThrshRequested Unsigned32, rtsIfBeVcMaxThrshInstalled Unsigned32 } rtsIfMaxThreshold OBJECT-TYPE SYNTAX Unsigned32 (0..4294967295) UNITS "cells" MAX-ACCESS read-only STATUS current DESCRIPTION "This object reflects the value of the Maximum Threshold installed in the traffic shaper hardware for this interface. This object is expressed in number of cell buffers. This object is not instantiated for interfaces to which it cannot be applied." ::= { rmTrafficShaperIfEntry 1 } rtsIfCellCount OBJECT-TYPE SYNTAX Gauge32 UNITS "cells" MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the count of cells queued to this interface in the traffic shaping hardware. This object is not instantiated for interfaces to which it cannot be applied." ::= { rmTrafficShaperIfEntry 2 } rtsIfVbrCfgRequested OBJECT-TYPE SYNTAX INTEGER { shapingDisable(1), -- Shaping disabled shapeToPcr(2), -- Shape to PCR only. shapeToScrAndPcr(3) -- Shape to PCR, SCR and MBS } MAX-ACCESS read-write STATUS current DESCRIPTION "If this object is set to the value 'shapingDisable', VBR connections(VC or VP) on this interface will not be shaped. If the object is set to the value 'shapeToScrAndPcr', the VBR (VC or VP) connections on this interface will be shaped to conform to their respective SCR, PCR and MBS traffic parameters. If this object is set to the value 'shapeToPcr', the VBR (VC or VP) connections on this interface will be shaped to conform to their respective PCR traffic parameter. Depending on the capabilities of the traffic shaping hardware, the changes to the traffic shaping configuration may or may not take effect immediately and may require that the traffic shaping hardware be reset to effect the change. The value of the object rtsIfVbrCfgInstalled will reflect the actual VBR Traffic Shaping configuration installed in the hardware currently. Depending on the capabilities of the traffic shaping hardware, the value of this object may or may not apply to terminating VBR VPs on this interface. This object is not instantiated for interfaces to which it cannot be applied." DEFVAL { shapingDisable } ::= { rmTrafficShaperIfEntry 3 } rtsIfVbrCfgInstalled OBJECT-TYPE SYNTAX INTEGER { shapingDisable(1), -- Shaping disabled shapeToPcr(2), -- Shape to PCR only. shapeToScrAndPcr(3) -- Shape to PCR, SCR and MBS } MAX-ACCESS read-only STATUS current DESCRIPTION "This object reflects the current VBR Traffic Shaping configuration installed in the hardware. This object is not instantiated for interfaces to which it cannot be applied." ::= { rmTrafficShaperIfEntry 4 } rtsIfBeCfgRequested OBJECT-TYPE SYNTAX INTEGER { shapingDisable(1), -- Shaping disabled shapeToPcr(2) -- Shape to PCR only. } MAX-ACCESS read-write STATUS current DESCRIPTION "This object reflects the traffic shaping configuration applied to Best-Effort Connections(VC or VP) belonging to UBR and ABR service categories on this interface. If this object is set to the value 'shapingDisable', best-effort connections(VC or VP) on this interface will not be shaped. If this object is set to the value 'shapeToPcr', the best-effort connections(VC or VP) on this interface will be shaped to conform to their respective PCR traffic parameter. Depending on the capabilities of the traffic shaping hardware, the changes to the traffic shaping configuration may or may not take effect immediately and may require that the traffic shaping hardware be reset to effect the change. The object rtsIfBeCfgInstalled will reflect the actual best-effort Traffic Shaping configuration installed in the hardware currently. Depending on the capabilities of the traffic shaping hardware, the value of this object may or may not apply to terminating best-effort VPs on this interface. This object is not instantiated for interfaces to which it cannot be applied." DEFVAL { shapingDisable } ::= { rmTrafficShaperIfEntry 5 } rtsIfBeCfgInstalled OBJECT-TYPE SYNTAX INTEGER { shapingDisable(1), -- Shaping disabled shapeToPcr(2) -- Shape to PCR only. } MAX-ACCESS read-only STATUS current DESCRIPTION "This object reflects the current Best-Effort Traffic Shaping configuration installed in the hardware. This object is not instantiated for interfaces to which it cannot be applied." ::= { rmTrafficShaperIfEntry 6 } rtsIfVbrClassMaxThrshRequested OBJECT-TYPE SYNTAX INTEGER (1..95) UNITS "percent" MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the Traffic Shaper Maximum Cell Buffer Threshold for the VBR Traffic Class. The value of this object is expressed as a percent of the value of rtsIfMaxThreshold object. A set request for this object will succeed only if the value of the ifAdminStatus object for this interface is 'down'. The Traffic Shaping hardware may not have the support to represent all the values and hence the value installed in hardware could be different. And the value installed in hardware will be available through the object rtsIfVbrClassMaxThrshInstalled. This object is not instantiated for interfaces to which it cannot be applied." ::= { rmTrafficShaperIfEntry 7 } rtsIfVbrClassMaxThrshInstalled OBJECT-TYPE SYNTAX Unsigned32 (0..4294967295) UNITS "cells" MAX-ACCESS read-only STATUS current DESCRIPTION "This object reflects the value of Maximum Class Threshold for VBR Traffic Class, in number of cell buffers, that is installed in the Traffic Shaping hardware. This object is not instantiated for interfaces to which it cannot be applied." ::= { rmTrafficShaperIfEntry 8 } rtsIfBeClassMaxThrshRequested OBJECT-TYPE SYNTAX INTEGER (1..95) UNITS "percent" MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the Traffic Shaper Maximum Cell Buffer Threshold for the Best-Effort Traffic Class. The value of this object is expressed as a percent of the value of rtsIfMaxThreshold object. A set request for this object will succeed only if the value of the ifAdminStatus object for this interface is 'down'. The Traffic Shaping hardware may not have the support to represent all the values and hence the value installed in hardware could be different. And this installed value will be available through the object rtsIfBeClassMaxThrshInstalled. This object is not instantiated for interfaces to which it cannot be applied." ::= { rmTrafficShaperIfEntry 9 } rtsIfBeClassMaxThrshInstalled OBJECT-TYPE SYNTAX Unsigned32 (0..4294967295) UNITS "cells" MAX-ACCESS read-only STATUS current DESCRIPTION "This object reflects the value of Maximum Class Threshold for Best-Effort Traffic Class, in number of cell buffers, that is installed in the Traffic Shaping hardware. This object is not instantiated for interfaces to which it cannot be applied." ::= { rmTrafficShaperIfEntry 10 } rtsIfVbrVcMaxThrshRequested OBJECT-TYPE SYNTAX Unsigned32 (0..4294967295) UNITS "cells" MAX-ACCESS read-write STATUS current DESCRIPTION "This object reflects the Maximum Threshold of the per-connection queues of VBR connections(VCs or VPs) in the traffic shaping hardware. The value of this object is expressed in number of cell buffers. Any change made to the value of this object will only effect subsequently established VBR connections and will not impact already existing VBR connections. The Traffic Shaping hardware may not have the support to represent all the values and hence the value installed in hardware could be different. And the value installed in hardware will be available through the object rtsIfVbrVcMaxThrshInstalled. This object is not instantiated for interfaces to which it cannot be applied." DEFVAL { 512 } ::= { rmTrafficShaperIfEntry 11 } rtsIfVbrVcMaxThrshInstalled OBJECT-TYPE SYNTAX Unsigned32 (0..4294967295) UNITS "cells" MAX-ACCESS read-only STATUS current DESCRIPTION "This object reflects the Maximum Threshold for the per-connection queues of VBR connections(VCs or VPs) that is installed in the Traffic Shaping hardware. The value of this object is expressed in number of cell buffers. This object is not instantiated for interfaces to which it cannot be applied." ::= { rmTrafficShaperIfEntry 12 } rtsIfBeVcMaxThrshRequested OBJECT-TYPE SYNTAX Unsigned32 (0..4294967295) UNITS "cells" MAX-ACCESS read-write STATUS current DESCRIPTION "This object reflects the Maximum Threshold of the per-connection queues of best-effort connections(VCs or VPs) in the traffic shaping hardware. The value of this object is expressed in number of cell buffers. Any change made to the value of this object will only effect subsequently established best-effort connections and will not impact already existing best-effort connections. The Traffic Shaping hardware may not have the support to represent all the values and hence the value installed in hardware could be different. And the value installed in hardware will be available through the object rtsIfBeVcMaxThrshInstalled. This object is not instantiated for interfaces to which it cannot be applied." DEFVAL { 1024 } ::= { rmTrafficShaperIfEntry 13 } rtsIfBeVcMaxThrshInstalled OBJECT-TYPE SYNTAX Unsigned32 (0..4294967295) UNITS "cells" MAX-ACCESS read-only STATUS current DESCRIPTION "This object reflects the Maximum Threshold for the per-connection queues of Best-Effort connections(VCs or VPs) that is installed in the Traffic Shaping hardware. The value of this object is expressed in number of cell buffers. This object is not instantiated for interfaces to which it cannot be applied." ::= { rmTrafficShaperIfEntry 14 } -- conformance information ciscoAtmRmMIBConformance OBJECT IDENTIFIER ::= { ciscoAtmRmMIB 3 } ciscoAtmRmMIBCompliances OBJECT IDENTIFIER ::= { ciscoAtmRmMIBConformance 1 } ciscoAtmRmMIBGroups OBJECT IDENTIFIER ::= { ciscoAtmRmMIBConformance 2 } -- compliance statements ciscoAtmRmMIBCompliance MODULE-COMPLIANCE STATUS obsolete -- superceded by ciscoAtmRmMIBCompliance2 DESCRIPTION "The compliance statement for the Cisco ATM Resource Management MIB." MODULE -- this module MANDATORY-GROUPS { atmRmSwitchCfgMIBGroup, atmRmPhyIfCfgMIBGroup, atmRmAllIfCfgMIBGroup, atmRmIfAllStateMIBGroup, atmRmIfStatsMIBGroup } ::= { ciscoAtmRmMIBCompliances 1 } ciscoAtmRmMIBCompliance2 MODULE-COMPLIANCE STATUS obsolete -- superceded by ciscoAtmRmMIBCompliance3 DESCRIPTION "The compliance statement for the Cisco ATM Resource Management MIB." MODULE -- this module MANDATORY-GROUPS { atmRmSwitchCfgMIBGroup2, atmRmPhyIfCfgMIBGroup2, atmRmAllIfCfgMIBGroup, atmRmIfAllStateMIBGroup2, atmRmIfStatsMIBGroup } ::= { ciscoAtmRmMIBCompliances 2 } ciscoAtmRmMIBCompliance3 MODULE-COMPLIANCE STATUS obsolete -- superceded by ciscoAtmRmMIBCompliance4 DESCRIPTION "The compliance statement for the Cisco ATM Resource Management MIB." MODULE -- this module MANDATORY-GROUPS { atmRmSwitchCfgMIBGroup2, atmRmPhyIfCfgMIBGroup3, atmRmAllIfCfgMIBGroup2, atmRmIfAllStateMIBGroup2, atmRmIfStatsMIBGroup } ::= { ciscoAtmRmMIBCompliances 3 } ciscoAtmRmMIBCompliance4 MODULE-COMPLIANCE STATUS obsolete -- superceded by ciscoAtmRmMIBCompliance5 DESCRIPTION "The compliance statement for the Cisco ATM Resource Management MIB." MODULE -- this module MANDATORY-GROUPS { atmRmSwitchCfgMIBGroup2, atmRmPhyIfCfgMIBGroup3, atmRmAllIfCfgMIBGroup3, atmRmIfAllStateMIBGroup2, atmRmIfStatsMIBGroup } ::= { ciscoAtmRmMIBCompliances 4 } ciscoAtmRmMIBCompliance5 MODULE-COMPLIANCE STATUS obsolete DESCRIPTION "The compliance statement for the Cisco ATM Resource Management MIB." MODULE -- this module MANDATORY-GROUPS { atmRmSwitchCfgMIBGroup2, atmRmPhyIfCfgMIBGroup3, atmRmAllIfCfgMIBGroup3, atmRmIfAllStateMIBGroup2, atmRmIfStatsMIBGroup, lsPerVcqAtmRmGroup2 } ::= { ciscoAtmRmMIBCompliances 5 } ciscoAtmRmMIBCompliance6 MODULE-COMPLIANCE STATUS obsolete -- superceded by ciscoAtmRmMIBCompliance7 DESCRIPTION "The compliance statement for the Cisco ATM Resource Management MIB." MODULE -- this module MANDATORY-GROUPS { atmRmSwitchCfgMIBGroup2, atmRmPhyIfCfgMIBGroup3, atmRmAllIfCfgMIBGroup3, atmRmIfAllStateMIBGroup2, atmRmIfStatsMIBGroup, lsPerVcqAtmRmGroup2, cgrPerVcqAtmRmGroup } ::= { ciscoAtmRmMIBCompliances 6 } ciscoAtmRmMIBCompliance7 MODULE-COMPLIANCE STATUS obsolete -- superceded by ciscoAtmRmMIBCompliance8 DESCRIPTION "The compliance statement for the Cisco ATM Resource Management MIB." MODULE -- this module MANDATORY-GROUPS { atmRmSwitchCfgMIBGroup2, atmRmPhyIfCfgMIBGroup4, atmRmAllIfCfgMIBGroup4, atmRmIfAllStateMIBGroup2, atmRmIfStatsMIBGroup, lsPerVcqAtmRmGroup2, cgrPerVcqAtmRmGroup } ::= { ciscoAtmRmMIBCompliances 7 } ciscoAtmRmMIBCompliance8 MODULE-COMPLIANCE STATUS obsolete -- superceded by ciscoAtmRmMIBCompliance9 DESCRIPTION "The compliance statement for the Cisco ATM Resource Management MIB." MODULE -- this module MANDATORY-GROUPS { atmRmSwitchCfgMIBGroup2, atmRmPhyIfCfgMIBGroup5, atmRmAllIfCfgMIBGroup4, atmRmIfAllStateMIBGroup2, atmRmIfStatsMIBGroup, lsPerVcqAtmRmGroup2, cgrPerVcqAtmRmGroup } ::= { ciscoAtmRmMIBCompliances 8 } ciscoAtmRmMIBCompliance9 MODULE-COMPLIANCE STATUS obsolete -- superceded by ciscoAtmRmMIBCompliance10 DESCRIPTION "The compliance statement for the Cisco ATM Resource Management MIB." MODULE -- this module MANDATORY-GROUPS { atmRmSwitchCfgMIBGroup2, atmRmPhyIfCfgMIBGroup5, atmRmAllIfCfgMIBGroup4, atmRmIfAllStateMIBGroup3, atmRmIfStatsMIBGroup, lsPerVcqAtmRmGroup2, cgrPerVcqAtmRmGroup } ::= { ciscoAtmRmMIBCompliances 9 } ciscoAtmRmMIBCompliance10 MODULE-COMPLIANCE STATUS obsolete -- superceded by ciscoAtmRmMIBCompliance11 DESCRIPTION "The compliance statement for the Cisco ATM Resource Management MIB." MODULE -- this module MANDATORY-GROUPS { atmRmSwitchCfgMIBGroup2, atmRmPhyIfCfgMIBGroup5, atmRmAllIfCfgMIBGroup5, atmRmIfAllStateMIBGroup3, atmRmIfStatsMIBGroup, lsPerVcqAtmRmGroup2, cgrPerVcqAtmRmGroup } ::= { ciscoAtmRmMIBCompliances 10 } ciscoAtmRmMIBCompliance11 MODULE-COMPLIANCE STATUS obsolete -- superceded by ciscoAtmRmMIBCompliance12 DESCRIPTION "The compliance statement for the Cisco ATM Resource Management MIB." MODULE -- this module MANDATORY-GROUPS { atmRmSwitchCfgMIBGroup2, atmRmPhyIfCfgMIBGroup5, atmRmAllIfCfgMIBGroup5, atmRmIfAllStateMIBGroup3, atmRmIfStatsMIBGroup, lsPerVcqAtmRmGroup2, cgrPerVcqAtmRmGroup2 } ::= { ciscoAtmRmMIBCompliances 11 } ciscoAtmRmMIBCompliance12 MODULE-COMPLIANCE STATUS deprecated -- superceded by ciscoAtmRmMIBCompliance13 DESCRIPTION "The compliance statement for the Cisco ATM Resource Management MIB." MODULE -- this module MANDATORY-GROUPS { atmRmSwitchCfgMIBGroup2, atmRmPhyIfCfgMIBGroup5, atmRmAllIfCfgMIBGroup5, atmRmIfAllStateMIBGroup3, atmRmIfStatsMIBGroup, lsPerVcqAtmRmGroup2, cgrPerVcqAtmRmGroup2, atmRmTrafficShaperIfGroup } ::= { ciscoAtmRmMIBCompliances 12 } ciscoAtmRmMIBCompliance13 MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for the Cisco ATM Resource Management MIB." MODULE -- this module MANDATORY-GROUPS { atmRmSwitchCfgMIBGroup2, atmRmPhyIfCfgMIBGroup5, atmRmAllIfCfgMIBGroup6, atmRmIfAllStateMIBGroup3, atmRmIfStatsMIBGroup, lsPerVcqAtmRmGroup2, cgrPerVcqAtmRmGroup2, atmRmTrafficShaperIfGroup, sharedMemAtmRmSwitchMIBGroup, sharedMemAtmRmPhyIfMIBGroup } ::= { ciscoAtmRmMIBCompliances 13 } -- units of conformance atmRmSwitchCfgMIBGroup OBJECT-GROUP OBJECTS { rmSwitchOverSubFactor, rmSwitchScrMarginFactor, rmSwitchAbrCongNotify, rmScDefaultQosMaxCtd, rmScDefaultQosPeakToPeakCdv, rmScDefaultQosClr } STATUS obsolete -- superceded by atmRmSwitchCfgMIBGroup2 DESCRIPTION "A collection of objects which provide ATM Switch Resource Management configuration." ::= { ciscoAtmRmMIBGroups 1 } sharedMemAtmRmSwitchMIBGroup OBJECT-GROUP OBJECTS { sharedMemRmSwitchQueuedCellLimit, sharedMemRmSwitchQueuedCellCount } STATUS current DESCRIPTION "A collection of objects which provide ATM Switch Resource Management information global to a shared-memory ATM switch." ::= { ciscoAtmRmMIBGroups 2 } atmRmPhyIfCfgMIBGroup OBJECT-GROUP OBJECTS { rmIfOutPacingRateRequested, rmIfOutPacingRateInstalled, rmIfOutPacingForce, rmIfDirControlLinkShareMaxAgg, rmIfDirControlLinkShareMinCbr, rmIfDirControlLinkShareMaxCbr, rmIfDirControlLinkShareMinVbr, rmIfDirControlLinkShareMaxVbr } STATUS obsolete -- superceded by atmRmPhyIfCfgMIBGroup2 DESCRIPTION "A collection of objects which provide ATM interface Resource Management configuration for physical interfaces." ::= { ciscoAtmRmMIBGroups 3 } atmRmAllIfCfgMIBGroup OBJECT-GROUP OBJECTS { rmIfLinkDistance, rmIfBestEffortLimit, rmIfDirMaxCbrPcr, rmIfDirMaxCbrTolerance, rmIfDirMaxVbrPcr, rmIfDirMaxVbrScr, rmIfDirMaxVbrTolerance, rmIfDirMaxAbrPcr, rmIfDirMaxAbrTolerance, rmIfDirMaxUbrPcr, rmIfDirMaxUbrTolerance } STATUS obsolete -- superceded by atmRmAllIfCfgMIBGroup2 DESCRIPTION "A collection of objects which provide ATM interface Resource Management configuration for all interfaces." ::= { ciscoAtmRmMIBGroups 4 } atmRmIfAllStateMIBGroup OBJECT-GROUP OBJECTS { rmIfScRxAcr, rmIfScTxAcr, rmIfScRxAlcr, rmIfScTxAlcr, rmIfScNumSvxConns, rmIfScNumPvxConns, rmIfScTxMaxCtd, rmIfScTxP2PeakCdv, rmIfScTxClr } STATUS obsolete -- superceded by atmRmIfAllStateMIBGroup2 DESCRIPTION "A collection of objects which provide ATM interface Resource Management status for all interfaces." ::= { ciscoAtmRmMIBGroups 5 } atmRmIfStatsMIBGroup OBJECT-GROUP OBJECTS { rmIfScRcacResultNumAdmit, rmIfScRcacResultNumTotalRequests, rmIfScRcacResultNumFailTraffComb, rmIfScRcacResultNumFailBw, rmIfScRcacResultNumFailLoss, rmIfScRcacResultNumFailDelay, rmIfScRcacResultNumFailCdv, rmIfScRcacResultNumFailBeLimit, rmIfScRcacResultNumFailParmLimit, rmIfScRcacResultNumFailOther } STATUS current DESCRIPTION "A collection of objects which provide ATM Switch Resource Management statistics." ::= { ciscoAtmRmMIBGroups 6 } sharedMemAtmRmPhyIfMIBGroup OBJECT-GROUP OBJECTS { sharedMemRmIfOutputQServCategory, sharedMemRmIfOutputQRequestedMaxSize, sharedMemRmIfOutputQInstalledMaxSize, sharedMemRmIfOutputQMaxSizeForce, sharedMemRmIfOutputQCellCount, sharedMemRmIfDiscardThreshold, sharedMemRmIfEfciThreshold, sharedMemRmIfAbrRelativeRateThreshold } STATUS current DESCRIPTION "A collection of objects which provide ATM interface Resource Management information for physical interfaces of a shared-memory ATM switch." ::= { ciscoAtmRmMIBGroups 7 } atmRmSwitchCfgMIBGroup2 OBJECT-GROUP OBJECTS { rmSwitchOverSubFactor, rmSwitchScrMarginFactor, rmSwitchAbrCongNotify, rmScDefaultQosMaxCtd, rmScDefaultQosPeakToPeakCdv, rmScDefaultQosClr, rmScDefaultQosClrClp01 } STATUS current DESCRIPTION "A collection of objects which provide ATM Switch Resource Management configuration." ::= { ciscoAtmRmMIBGroups 8 } atmRmPhyIfCfgMIBGroup2 OBJECT-GROUP OBJECTS { rmIfOutPacingRateRequested, rmIfOutPacingRateInstalled, rmIfOutPacingForce, rmIfDirControlLinkShareMaxAgg, rmIfDirControlLinkShareMinCbr, rmIfDirControlLinkShareMaxCbr, rmIfDirControlLinkShareMinVbr, rmIfDirControlLinkShareMaxVbr, rmIfCbrDefaultRxUpcTolerance, rmIfVbrRtDefaultRxUpcTolerance, rmIfVbrNrtDefaultRxUpcTolerance, rmIfAbrDefaultRxUpcTolerance, rmIfUbrDefaultRxUpcTolerance } STATUS obsolete -- superceded by atmRmPhyIfCfgMIBGroup2 DESCRIPTION "A collection of objects which provide ATM interface Resource Management configuration for physical interfaces." ::= { ciscoAtmRmMIBGroups 9 } atmRmIfAllStateMIBGroup2 OBJECT-GROUP OBJECTS { rmIfScRxAcr, rmIfScTxAcr, rmIfScRxAlcr, rmIfScTxAlcr, rmIfScNumSvxConns, rmIfScNumPvxConns, rmIfScTxMaxCtd, rmIfScTxP2PeakCdv, rmIfScTxClr, rmIfScTxClrClp01 } STATUS obsolete -- superceded by atmRmIfAllStateMIBGroup3 DESCRIPTION "A collection of objects which provide ATM interface Resource Management status for all interfaces." ::= { ciscoAtmRmMIBGroups 10 } lsPerVcqAtmRmGroup OBJECT-GROUP OBJECTS { lsPerVcqRmIfMinWrrServiceClass, lsPerVcqRmIfServClassConnType, lsPerVcqRmIfServClassWrrWeight, lsPerVcqRmThreshGrpMaxSize, lsPerVcqRmThreshGrpQMaxSize, lsPerVcqRmThreshGrpQMinSize, lsPerVcqRmThreshGrpDiscThreshold, lsPerVcqRmThreshGrpMarkThreshold, lsPerVcqRmThreshGrpName, lsPerVcqRmThreshGrpCellCount, lsPerVcqRmThreshGrpServGroup } STATUS obsolete DESCRIPTION "A collection of objects which provide ATM Resource Management status on platforms using the Lightstream per-VC queueing chipset." ::= { ciscoAtmRmMIBGroups 11 } atmRmPhyIfCfgMIBGroup3 OBJECT-GROUP OBJECTS { rmIfOutPacingRateRequested, rmIfOutPacingRateInstalled, rmIfOutPacingForce, rmIfDirControlLinkShareMaxAgg, rmIfDirControlLinkShareMinCbr, rmIfDirControlLinkShareMaxCbr, rmIfDirControlLinkShareMinVbr, rmIfDirControlLinkShareMaxVbr, rmIfCbrDefaultRxUpcTolerance, rmIfVbrRtDefaultRxUpcTolerance, rmIfVbrNrtDefaultRxUpcTolerance, rmIfAbrDefaultRxUpcTolerance, rmIfUbrDefaultRxUpcTolerance, rmIfVbrRtDefaultRxUpcCdvt, rmIfVbrNrtDefaultRxUpcCdvt, rmIfDirControlLinkShareMinAbr, rmIfDirControlLinkShareMaxAbr, rmIfDirControlLinkShareMinUbr, rmIfDirControlLinkShareMaxUbr } STATUS obsolete -- superceded by atmRmPhyIfCfgMIBGroup4 DESCRIPTION "A collection of objects which provide ATM interface Resource Management configuration for physical interfaces." ::= { ciscoAtmRmMIBGroups 12 } atmRmAllIfCfgMIBGroup2 OBJECT-GROUP OBJECTS { rmIfLinkDistance, rmIfBestEffortLimit, rmIfDirMaxCbrPcr, rmIfDirMaxCbrTolerance, rmIfDirMaxVbrPcr, rmIfDirMaxVbrScr, rmIfDirMaxVbrTolerance, rmIfDirMaxAbrPcr, rmIfDirMaxAbrTolerance, rmIfDirMaxUbrPcr, rmIfDirMaxUbrTolerance, rmIfDirMaxAbrMcr, rmIfDirMaxUbrMcr, rmIfDirMaxVbrCdvt } STATUS obsolete -- superceded by atmRmAllIfCfgMIBGroup3 DESCRIPTION "A collection of objects which provide ATM interface Resource Management configuration for all interfaces." ::= { ciscoAtmRmMIBGroups 13 } atmRmAllIfCfgMIBGroup3 OBJECT-GROUP OBJECTS { rmIfLinkDistance, rmIfBestEffortLimit, rmIfDirMaxCbrPcr, rmIfDirMaxCbrTolerance, rmIfDirMaxVbrPcr, rmIfDirMaxVbrScr, rmIfDirMaxVbrTolerance, rmIfDirMaxAbrPcr, rmIfDirMaxAbrTolerance, rmIfDirMaxUbrPcr, rmIfDirMaxUbrTolerance, rmIfDirMaxAbrMcr, rmIfDirMaxUbrMcr, rmIfDirMaxVbrCdvt, rmIfServCategorySupport } STATUS obsolete -- superceded by atmRmAllIfCfgMIBGroup4 DESCRIPTION "A collection of objects which provide ATM interface Resource Management configuration for all interfaces." ::= { ciscoAtmRmMIBGroups 14 } lsPerVcqAtmRmGroup2 OBJECT-GROUP OBJECTS { lsPerVcqRmIfMinWrrServiceClass, lsPerVcqRmIfServClassConnType, lsPerVcqRmIfServClassWrrWeight, lsPerVcqRmThreshGrpMaxSize, lsPerVcqRmThreshGrpQMaxSize, lsPerVcqRmThreshGrpQMinSize, lsPerVcqRmThreshGrpDiscThreshold, lsPerVcqRmThreshGrpMarkThreshold, lsPerVcqRmThreshGrpName, lsPerVcqRmThreshGrpCellCount, lsPerVcqRmThreshGrpServGroup, lsPerVcqRmHierarchicalSchedulingMode } STATUS current DESCRIPTION "A collection of objects which provide ATM Resource Management status on platforms using the Lightstream per-VC queueing chipset." ::= { ciscoAtmRmMIBGroups 15 } cgrPerVcqAtmRmGroup OBJECT-GROUP OBJECTS { cgrPerVcqRmThreshGrpQMaxSize, cgrPerVcqRmThreshGrpQMinSize, cgrPerVcqRmThreshGrpDiscThreshold, cgrPerVcqRmThreshGrpMarkThreshold, cgrPerVcqRmThreshGrpName, cgrPerVcqRmThreshGrpCellCount, cgrPerVcqRmThreshGrpServGroup, cgrPerVcqRmHierarchicalSchedulingMode } STATUS obsolete -- superceded by cgrPerVcqAtmRmGroup2 DESCRIPTION "A collection of objects which provide ATM Resource Management status on the Catalyst8540MSR platform." ::= { ciscoAtmRmMIBGroups 16 } atmRmAllIfCfgMIBGroup4 OBJECT-GROUP OBJECTS { rmIfLinkDistance, rmIfBestEffortLimit, rmIfDirMaxCbrPcr, rmIfDirMaxCbrTolerance, rmIfDirMaxVbrPcr, rmIfDirMaxVbrScr, rmIfDirMaxVbrTolerance, rmIfDirMaxAbrPcr, rmIfDirMaxAbrTolerance, rmIfDirMaxUbrPcr, rmIfDirMaxUbrTolerance, rmIfDirMaxAbrMcr, rmIfDirMaxUbrMcr, rmIfDirMaxVbrCdvt, rmIfServCategorySupport, rmIfCbrDefaultRxUpcTolerance, rmIfVbrRtDefaultRxUpcTolerance, rmIfVbrNrtDefaultRxUpcTolerance, rmIfAbrDefaultRxUpcTolerance, rmIfUbrDefaultRxUpcTolerance, rmIfVbrRtDefaultRxUpcCdvt, rmIfVbrNrtDefaultRxUpcCdvt } STATUS obsolete -- superceded by atmRmAllIfCfgMIBGroup5 DESCRIPTION "A collection of objects which provide ATM interface Resource Management configuration for all interfaces." ::= { ciscoAtmRmMIBGroups 17 } atmRmPhyIfCfgMIBGroup4 OBJECT-GROUP OBJECTS { rmIfOutPacingRateRequested, rmIfOutPacingRateInstalled, rmIfOutPacingForce, rmIfDirControlLinkShareMaxAgg, rmIfDirControlLinkShareMinCbr, rmIfDirControlLinkShareMaxCbr, rmIfDirControlLinkShareMinVbr, rmIfDirControlLinkShareMaxVbr, rmIfDirControlLinkShareMinAbr, rmIfDirControlLinkShareMaxAbr, rmIfDirControlLinkShareMinUbr, rmIfDirControlLinkShareMaxUbr } STATUS obsolete -- superceded by atmRmPhyIfCfgMIBGroup5 DESCRIPTION "A collection of objects which provide ATM interface Resource Management configuration for physical interfaces." ::= { ciscoAtmRmMIBGroups 18 } atmRmPhyIfCfgMIBGroup5 OBJECT-GROUP OBJECTS { rmIfOutPacingRateRequested, rmIfOutPacingRateInstalled, rmIfOutPacingForce, rmIfDirControlLinkShareMaxAgg, rmIfDirControlLinkShareMinCbr, rmIfDirControlLinkShareMaxCbr, rmIfDirControlLinkShareMinVbr, rmIfDirControlLinkShareMaxVbr, rmIfDirControlLinkShareMinAbr, rmIfDirControlLinkShareMaxAbr, rmIfDirControlLinkShareMinUbr, rmIfDirControlLinkShareMaxUbr, rmIfFramingOverhead, rmIfFramingOverheadForce } STATUS current DESCRIPTION "A collection of objects which provide ATM interface Resource Management configuration for physical interfaces." ::= { ciscoAtmRmMIBGroups 19 } atmRmIfAllStateMIBGroup3 OBJECT-GROUP OBJECTS { rmIfScRxAcr, rmIfScTxAcr, rmIfScRxAlcr, rmIfScTxAlcr, rmIfScNumSvxConns, rmIfScNumPvxConns, rmIfScTxMaxCtd, rmIfScTxP2PeakCdv, rmIfScTxClr,rmIfScTxClrClp01, rmIfScRxDynBwSvcAcr, rmIfScTxDynBwSvcAcr } STATUS current DESCRIPTION "A collection of objects which provide ATM interface Resource Management status for all interfaces." ::= { ciscoAtmRmMIBGroups 20 } atmRmAllIfCfgMIBGroup5 OBJECT-GROUP OBJECTS { rmIfLinkDistance, rmIfBestEffortLimit, rmIfDirMaxCbrPcr, rmIfDirMaxCbrTolerance, rmIfDirMaxVbrPcr, rmIfDirMaxVbrScr, rmIfDirMaxVbrTolerance, rmIfDirMaxAbrPcr, rmIfDirMaxAbrTolerance, rmIfDirMaxUbrPcr, rmIfDirMaxUbrTolerance, rmIfDirMaxAbrMcr, rmIfDirMaxUbrMcr, rmIfDirMaxVbrCdvt, rmIfServCategorySupport, rmIfCbrDefaultRxUpcTolerance, rmIfVbrRtDefaultRxUpcTolerance, rmIfVbrNrtDefaultRxUpcTolerance, rmIfAbrDefaultRxUpcTolerance, rmIfUbrDefaultRxUpcTolerance, rmIfVbrRtDefaultRxUpcCdvt, rmIfVbrNrtDefaultRxUpcCdvt, rmIfOverBooking } STATUS deprecated -- superceded by atmRmAllIfCfgMIBGroup6 DESCRIPTION "A collection of objects which provide ATM interface Resource Management configuration for all interfaces." ::= { ciscoAtmRmMIBGroups 21 } cgrPerVcqAtmRmGroup2 OBJECT-GROUP OBJECTS { cgrPerVcqRmThreshGrpQMaxSize, cgrPerVcqRmThreshGrpQMinSize, cgrPerVcqRmThreshGrpDiscThreshold, cgrPerVcqRmThreshGrpMaxSize, cgrPerVcqRmThreshGrpMarkThreshold, cgrPerVcqRmThreshGrpName, cgrPerVcqRmThreshGrpCellCount, cgrPerVcqRmThreshGrpServGroup, cgrPerVcqRmHierarchicalSchedulingMode } STATUS current DESCRIPTION "A collection of objects which provide ATM Resource Management status on the Catalyst8540MSR platform." ::= { ciscoAtmRmMIBGroups 22 } atmRmTrafficShaperIfGroup OBJECT-GROUP OBJECTS { rtsIfMaxThreshold, rtsIfCellCount, rtsIfVbrCfgRequested, rtsIfVbrCfgInstalled, rtsIfBeCfgRequested, rtsIfBeCfgInstalled, rtsIfVbrClassMaxThrshRequested, rtsIfVbrClassMaxThrshInstalled, rtsIfBeClassMaxThrshRequested, rtsIfBeClassMaxThrshInstalled, rtsIfVbrVcMaxThrshRequested, rtsIfVbrVcMaxThrshInstalled, rtsIfBeVcMaxThrshRequested, rtsIfBeVcMaxThrshInstalled } STATUS current DESCRIPTION "A collection of objects which provide ATM Traffic Shaper configuration and state information for ATM interfaces." ::= { ciscoAtmRmMIBGroups 23 } atmRmAllIfCfgMIBGroup6 OBJECT-GROUP OBJECTS { rmIfLinkDistance, rmIfBestEffortLimit, rmIfDirMaxCbrPcr, rmIfDirMaxCbrTolerance, rmIfDirMaxVbrPcr, rmIfDirMaxVbrScr, rmIfDirMaxVbrTolerance, rmIfDirMaxAbrPcr, rmIfDirMaxAbrTolerance, rmIfDirMaxUbrPcr, rmIfDirMaxUbrTolerance, rmIfDirMaxAbrMcr, rmIfDirMaxUbrMcr, rmIfDirMaxVbrCdvt, rmIfServCategorySupport, rmIfCbrDefaultRxUpcTolerance, rmIfVbrRtDefaultRxUpcTolerance, rmIfVbrNrtDefaultRxUpcTolerance, rmIfAbrDefaultRxUpcTolerance, rmIfUbrDefaultRxUpcTolerance, rmIfVbrRtDefaultRxUpcCdvt, rmIfVbrNrtDefaultRxUpcCdvt, rmIfOverBooking, rmIfVbrRtPerClassOverbooking, rmIfVbrNrtPerClassOverbooking, rmIfAbrPerClassOverbooking, rmIfUbrPerClassOverbooking } STATUS current DESCRIPTION "A collection of objects which provide ATM interface Resource Management configuration for all interfaces." ::= { ciscoAtmRmMIBGroups 24 } END