-- CISCO ATM connection management MIB -- -- Jan 1996, Yunsen Wang -- -- Copyright (c) 1996-1999, 2001 by cisco Systems, Inc. -- All rights reserved. -- ***************************************************************** CISCO-ATM-CONN-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, Counter32,Integer32,Gauge32 FROM SNMPv2-SMI TEXTUAL-CONVENTION, TimeStamp, TruthValue, RowStatus FROM SNMPv2-TC ifIndex, InterfaceIndexOrZero FROM IF-MIB atmVplVpi, atmVclVpi, atmVclVci, AtmTrafficDescrParamIndex FROM ATM-MIB NsapAtmAddr FROM CISCO-ATM-IF-MIB ciscoExperiment FROM CISCO-SMI MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF LsPerVcqThresholdGroup FROM CISCO-ATM-RM-MIB SnmpAdminString FROM SNMP-FRAMEWORK-MIB; ciscoAtmConnMIB MODULE-IDENTITY LAST-UPDATED "200207120000Z" ORGANIZATION "Cisco Systems, Inc." CONTACT-INFO " Cisco Systems Customer Service Postal: 170 W Tasman Drive San Jose, CA 95134 USA Tel: +1 800 553-NETS E-mail: cs-atm@cisco.com" DESCRIPTION "This MIB module is a cisco extension to VPL/VCL table defined in rfc1695 for ATM switch connection management." REVISION "200207120000Z" DESCRIPTION "Added a new enumeration 'useTrafficDescr' to the syntax of ciscoAtmVclEpdEnable." REVISION "200110300000Z" DESCRIPTION "Added ciscoAtmVplConnType and ciscoAtmVclConnType objects to the VPL and VCL tables." REVISION "200110100000Z" DESCRIPTION "Added ciscoAtmVplConnName and ciscoAtmVclConnName objects to the VPL and VCL tables." REVISION "200108060000Z" DESCRIPTION "Added a enumeration for ConfigType to enable configuration of Passive Half leg for 2-ended Soft PVC/PVP" REVISION "200101290000Z" DESCRIPTION "Added objects that provide per-connection Transmit statistics for the switch fabric." REVISION "9810020000Z" DESCRIPTION "Added objects for reporting negotiated traffic parameters." REVISION "9705260000Z" DESCRIPTION "Added objects for management of new features made possible on the LS1010 by the Feature Card Plus. This includes support for: - per-VC queueing hardware structures, - enhanced UPC, - per-connection snooping, - enhanced per-connection statistics." REVISION "9611010000Z" DESCRIPTION "Added - VPL/VCL violation counter, - SVC frame discard using AAL5IE, - default VPL/VCL tolerance objects." REVISION "9807260000Z" DESCRIPTION "Added - object to configure a VP leg as a hierarchical VP." ::= { ciscoExperiment 13 } -- assigned by cana@cisco.com -- -- Caution. This MIB is temporary and experimental. -- In the future will be removed from products, -- perhaps with short notice, in favor of more standard -- or generic MIBs. Application developers should not -- depend on long-term access to this MIB. -- ciscoAtmConnMIBObjects OBJECT IDENTIFIER ::= { ciscoAtmConnMIB 1 } CastType ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Specifies the type of the connection. It can be either a point to point connection or point to multipoint root or leaf." SYNTAX INTEGER { pointToPoint(1), pointToMultiPointRoot(2), pointToMultiPointLeaf(3) } ConfigType ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Specifies whether it's a permanent, switched, soft or soft passive config type." SYNTAX INTEGER { other(1), permanent(2), switch(3), soft(4), softPassive(5) } SpanType ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The SpanType textual convention is used to specify different connection span types. The connection span types are: - 'unknown', which indicates that the connection entry is not cross-connected. - 'transit', which indicates that the connection entry is cross-connected and is not a connection end point. - 'terminate', which indicates that the connection entry is cross-connected and is a connection end point. - 'both', which indicates that the connection is transit as well as terminating. This will be true only if the connection cast type is a pointToMultiPointRoot and has transit and terminating connection leaves. None of the above values may be specified in a management protocol set operation." SYNTAX INTEGER { unknown(1), -- not installed transit(2), terminate(3), both(4) -- p2mp root } EnableStatus ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Enable or Disable operation." SYNTAX INTEGER { enable(1), disable(2) } UpcStatus ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Define the Usage Parameter Control (UPC) operation as one of pass,tag or drop at this connection." SYNTAX INTEGER { passing(1), tagging(2), dropping(3), localShaping(4) } ConnState ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The ConnState textual convention is used to specify different connection states. The connections states are: - 'setup', which indicates that the connection entry is to be created and installed in the hardware and software connection tables. - 'release', which indicates that the connection entry is to be removed from the hardware and software connection tables. - 'notInstalled', which indicates connection entry is created only in the software connection tables. The connection entry is not installed in the hardware connection table. - 'down' which indicates that connection is down and is present in both software and hardware connection tables. - 'up' which indicates that connection is up and is present in both software and hardware connection tables. - 'setup' and 'release' are only two values may be specified in a management protocol set operation, only three values will be returned in response to a management protocol retrieval operation: 'notInstalled', 'down' or 'up'." SYNTAX INTEGER { setup(1), release(2), notInstalled(3), down(4), up(5) } Location ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Location of calling or called or unknown." SYNTAX INTEGER { unknown(1), calling(2), called(3) } Direction ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Calling or called side associated with address." SYNTAX INTEGER { unknown(1), p2pCallingSide(2), p2pCalledSide(3), p2mpRoot(4), p2mpLeaf(5) } SnoopDirType ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Direction of Snooped Traffic" SYNTAX INTEGER { transmit(1), receive(2) } -- This group is an extension of VPL table ciscoAtmVpl OBJECT IDENTIFIER ::= { ciscoAtmConnMIBObjects 1 } ciscoAtmVplTable OBJECT-TYPE SYNTAX SEQUENCE OF CiscoAtmVplEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The Virtual Path Link extension Table." ::= { ciscoAtmVpl 1 } ciscoAtmVplEntry OBJECT-TYPE SYNTAX CiscoAtmVplEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " An entry in the Vpl table.This entry is used to model a bi-directional Vpl. This table augments the atmVplTable defined in RFC 1695. However it uses ifIndex and atmVplVpi as an Index for historical reasons. The entries are created/deleted as a by-product of creating and deleting entries in the atmVplTable." INDEX { ifIndex,atmVplVpi } ::= { ciscoAtmVplTable 1 } CiscoAtmVplEntry ::= SEQUENCE { -- config info ciscoAtmVplCastType CastType, ciscoAtmVplSpanType SpanType, ciscoAtmVplConfigType ConfigType, ciscoAtmVplRxUpcMode UpcStatus, -- connection state ciscoAtmVplConnState ConnState, -- oam config info ciscoAtmVplOamLoopbkTxInterval Integer32, ciscoAtmVplOamSegmentLoopback EnableStatus, ciscoAtmVplOamEndLoopback EnableStatus, ciscoAtmVplOamAisEnable EnableStatus, ciscoAtmVplOamRdiEnable EnableStatus, -- per vc statistics ciscoAtmVplInstallTime TimeStamp, ciscoAtmVplInCells Counter32, ciscoAtmVplOutCells Counter32, -- cross side connection info ciscoAtmVplCrossIfIndex InterfaceIndexOrZero, ciscoAtmVplCrossVpi Integer32, ciscoAtmVplNextLeafIfIndex InterfaceIndexOrZero, ciscoAtmVplNextLeafVpi Integer32, -- soft PVP ciscoAtmVplRemoteAddr NsapAtmAddr, ciscoAtmVplRemoteVpi Integer32, ciscoAtmVplLocation Location, ciscoAtmVplSlowRetryIntv Integer32, ciscoAtmVplNumAttempts Counter32, ciscoAtmVplLastReleaseCause Integer32, -- logical port ciscoAtmVplLogicalPortDef INTEGER, ciscoAtmVplLogicalPortIndex InterfaceIndexOrZero, -- per vc violation stats ciscoAtmVplUpcViolations Counter32, ciscoAtmVplEpdTpdCellDrops Counter32, ciscoAtmVplEpdTpdPacketDrops Counter32, ciscoAtmVplEpdTpdPacketsIn Counter32, ciscoAtmVplClp1Drops Counter32, -- default tolerance ciscoAtmVplDefaultRxUpcTolerance Integer32, ciscoAtmVplDefaultRxUpcVbrCdvt Integer32, -- lightstream per-vc queueing -- switch chipset objects ciscoAtmVplLsPerVcqWrrWeight INTEGER, ciscoAtmVplLsPerVcqTunnelIsShaped TruthValue, ciscoAtmVplLsPerVcqXmtQueuedCells Gauge32, ciscoAtmVplLsPerVcQThreshGrp LsPerVcqThresholdGroup, -- feature card per-flow queueing -- (FC-PFQ) per-VPL statistics objects ciscoAtmVplInClp0Cells Counter32, ciscoAtmVplInClp1Cells Counter32, ciscoAtmVplOutClp0Cells Counter32, ciscoAtmVplOutClp1Cells Counter32, ciscoAtmVplCellDrops Counter32, ciscoAtmVplClp0VcqFullCellDrops Counter32, ciscoAtmVplVcqClpThreshCellDrops Counter32, -- feature card per-flow queueing -- Hierarchical VP-Tunnel ciscoAtmVplLsPerVcqTunnelIsHierarchical TruthValue, -- Objects for negotiated traffic parameters ciscoAtmVplRxNegTraffDescrIndex AtmTrafficDescrParamIndex, ciscoAtmVplTxNegTraffDescrIndex AtmTrafficDescrParamIndex, -- Switch Fabric Tx Statistics ciscoAtmVplSwFabOutCells Counter32, ciscoAtmVplSwFabOutClp0Cells Counter32, ciscoAtmVplSwFabOutClp1Cells Counter32, -- Connection info ciscoAtmVplConnName SnmpAdminString, ciscoAtmVplConnType INTEGER } ciscoAtmVplCastType OBJECT-TYPE SYNTAX CastType MAX-ACCESS read-write STATUS current DESCRIPTION " Vpl type is either a point to point connection or point to multipoint root or leaf." DEFVAL { pointToPoint } ::= { ciscoAtmVplEntry 1 } ciscoAtmVplSpanType OBJECT-TYPE SYNTAX SpanType MAX-ACCESS read-only STATUS current DESCRIPTION " Vpl span is either a transit one or a terminating one." DEFVAL { transit } ::= { ciscoAtmVplEntry 2 } ciscoAtmVplConfigType OBJECT-TYPE SYNTAX ConfigType MAX-ACCESS read-write STATUS current DESCRIPTION " Vpl type is either a PVC, SVC, Soft PVC or Soft Passive half leg. The half leg can be set to Passive through user configuration only." DEFVAL { permanent } ::= { ciscoAtmVplEntry 3 } ciscoAtmVplRxUpcMode OBJECT-TYPE SYNTAX UpcStatus MAX-ACCESS read-write STATUS current DESCRIPTION " Usage Parameter Control opeartion is pass,tag,drop or local shaping at this connection." DEFVAL { passing } ::= { ciscoAtmVplEntry 4 } ciscoAtmVplConnState OBJECT-TYPE SYNTAX ConnState MAX-ACCESS read-write STATUS current DESCRIPTION "The connection state of this VPL. " ::= { ciscoAtmVplEntry 5 } ciscoAtmVplOamLoopbkTxInterval OBJECT-TYPE SYNTAX Integer32 (5..60) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "Frequency of OAM loopback cells generated." DEFVAL { 5 } ::= { ciscoAtmVplEntry 6 } ciscoAtmVplOamSegmentLoopback OBJECT-TYPE SYNTAX EnableStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Enable segment loopback on this virtual path." DEFVAL { disable } ::= { ciscoAtmVplEntry 7 } ciscoAtmVplOamEndLoopback OBJECT-TYPE SYNTAX EnableStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Enable end to end loopback on this virtual path." DEFVAL { disable } ::= { ciscoAtmVplEntry 8 } ciscoAtmVplOamAisEnable OBJECT-TYPE SYNTAX EnableStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Enable Alarm Indication Signal OAM cell generation if the interafce goes down on a crossconnect virtual path." DEFVAL { disable } ::= { ciscoAtmVplEntry 9 } ciscoAtmVplOamRdiEnable OBJECT-TYPE SYNTAX EnableStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Enable Remote Defect Indication OAM cell generation if an Alarm Indication Signal OAM cell is received." DEFVAL { disable } ::= { ciscoAtmVplEntry 10 } ciscoAtmVplInstallTime OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "The time stamp derived from sysUpTime when this VPL gets created. The VPL entries are created/deleted as a by-product of creating and deleting entries in the atmVplTable defined in RFC1695." ::= { ciscoAtmVplEntry 11 } ciscoAtmVplInCells OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of cells received on this VPL." ::= { ciscoAtmVplEntry 12 } ciscoAtmVplOutCells OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of cells transmitted on this VPL." ::= { ciscoAtmVplEntry 13 } ciscoAtmVplCrossIfIndex OBJECT-TYPE SYNTAX InterfaceIndexOrZero MAX-ACCESS read-write STATUS current DESCRIPTION "For point to point, this is the cross-connected VPL's ifIndex of this VPL. For point to multi-point connection, this will be the root VPL's ifIndex for a leaf VPL entry in the multicast chain, or it's the 1st leaf for a root VPL entry. If it's zero, it means it's not cross-connected yet. Atomically set ciscoAtmVplConnState, ciscoAtmVplCrossIfIndex and ciscoAtmVplCrossVpi will create or delete a cross connection to crossed half leg of this ciscoAtmVplCrossIfindex and ciscoAtmVplCrossVpi for p2p PVP, or add or drop a multicast connection of this ciscoAtmVplCrossIfindex and ciscoAtmVplCrossVpi to/from the root on the multicast chain for p2mp PVP." DEFVAL { 0 } ::= { ciscoAtmVplEntry 14 } ciscoAtmVplCrossVpi OBJECT-TYPE SYNTAX Integer32 (0..4095) MAX-ACCESS read-write STATUS current DESCRIPTION "This specifies the VPI value of the VPL to which this VPL is cross-connected. For point to multi-point connection, this is the root VPL's VPI for the leaf entry. Similarly it is the 1st leaf's VPI value for the root entry." DEFVAL { 0 } ::= { ciscoAtmVplEntry 15 } ciscoAtmVplNextLeafIfIndex OBJECT-TYPE SYNTAX InterfaceIndexOrZero MAX-ACCESS read-only STATUS current DESCRIPTION "For point to point, this is zero i.e. not used. For point to multi-point connection, this will be the next leaf VPL's ifIndex on the multicast chain. This will be 0 if this is the root VPL entry. If it's zero for a leaf VPL, it means this is the last leaf." DEFVAL { 0 } ::= { ciscoAtmVplEntry 16 } ciscoAtmVplNextLeafVpi OBJECT-TYPE SYNTAX Integer32 (0..4095) MAX-ACCESS read-only STATUS current DESCRIPTION "For point to point, this is zero i.e. not used. This apply only to point to multi-point connection, this will be the next leaf VPL's VPI on the multicast chain." DEFVAL { 0 } ::= { ciscoAtmVplEntry 17 } ciscoAtmVplRemoteAddr OBJECT-TYPE SYNTAX NsapAtmAddr MAX-ACCESS read-write STATUS current DESCRIPTION "Soft PVP target address if this is the calling side Soft PVP source address if this is called side. Atomically set ConnState, RemoteAddr and RemoteVpi will create or delete a soft PVP. Atomically set ConnState, RemoteAddr without RemoteVpi will also create or delete a soft PVP but let target switch assign the vpi." ::= { ciscoAtmVplEntry 18 } ciscoAtmVplRemoteVpi OBJECT-TYPE SYNTAX Integer32 (0..4095) MAX-ACCESS read-write STATUS current DESCRIPTION "Soft PVP target VPI in calling side. 0 in called side." ::= { ciscoAtmVplEntry 19 } ciscoAtmVplLocation OBJECT-TYPE SYNTAX Location MAX-ACCESS read-only STATUS current DESCRIPTION "Indicate calling or called side of a soft PVP. If ciscoAtmVplConfigType is not soft then ciscoAtmVplLocation value should be ignored." ::= { ciscoAtmVplEntry 20 } ciscoAtmVplSlowRetryIntv OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "Soft PVP slow retry interval time in seconds." ::= { ciscoAtmVplEntry 21 } ciscoAtmVplNumAttempts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of retries made to install this soft PVP connection. If ciscoAtmVplConfigType is not soft then ciscoAtmVplNumAttempts value should be ignored." ::= { ciscoAtmVplEntry 22 } ciscoAtmVplLastReleaseCause OBJECT-TYPE SYNTAX Integer32(1..127) MAX-ACCESS read-only STATUS current DESCRIPTION "Value of the Cause field of the Cause Information Element in the last Release Signalling message received for this SPVP. Indicates the reason for the Release. ciscoAtmVplConfigType is not soft then ciscoAtmVplLastReleaseCause value should be ignored." REFERENCE "ATM Forum's UNI3.0/3.1 Speicifcation" ::= { ciscoAtmVplEntry 23 } ciscoAtmVplLogicalPortDef OBJECT-TYPE SYNTAX INTEGER { notLogicalIf(1), isLogicalIf(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Indicates whether the VPC at this VPL interface is an Atm Logical Port interface." DEFVAL { notLogicalIf } ::= { ciscoAtmVplEntry 24 } ciscoAtmVplLogicalPortIndex OBJECT-TYPE SYNTAX InterfaceIndexOrZero MAX-ACCESS read-only STATUS current DESCRIPTION "The ifTable index of the Atm logical port interface associated with this VPL. Only valid if the value of atmVplLogicalPortDef is isLogicalIf, and the VPL row is active." ::= { ciscoAtmVplEntry 25 } ciscoAtmVplUpcViolations OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of nonconforming cells detected by Usage Parameter Control (UPC) for cells received on this VPL. On LS1010 systems, this counter is valid only if equipped with the Feature Card - Per Flow Queueing." ::= { ciscoAtmVplEntry 26 } ciscoAtmVplEpdTpdCellDrops OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS obsolete DESCRIPTION "Never implemented." ::= { ciscoAtmVplEntry 27 } ciscoAtmVplEpdTpdPacketDrops OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS obsolete DESCRIPTION "Never implemented." ::= { ciscoAtmVplEntry 28 } ciscoAtmVplEpdTpdPacketsIn OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS obsolete DESCRIPTION "Never implemented." ::= { ciscoAtmVplEntry 29 } ciscoAtmVplClp1Drops OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS obsolete DESCRIPTION "Never implemented." ::= { ciscoAtmVplEntry 30 } ciscoAtmVplDefaultRxUpcTolerance OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "If the tolerance (CDVT for CBR, ABR, UBR connections, Maximum Burst Size for VBR connectons) requested for Usage Parameter Control is not explicitly specified in VPL creation, this object contains the default that is used. If tolerance is explicitly specified in VPL creation, it can be found in the Traffic Table row specified by atmVplReceiveTrafficDescrIndex, and the value of this object is -1." ::= { ciscoAtmVplEntry 31 } ciscoAtmVplDefaultRxUpcVbrCdvt OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "If the Cell Delay Variation Tolerance (CDVT) requested for Usage Parameter Control for a VBR connection is not explicitly specified in VPL creation, this object contains the default that is used. If CDVT is explicitly specified in VPL creation, it can be found in the Traffic Table row specified by atmVplReceiveTrafficDescrIndex, and the value of this object is -1." ::= { ciscoAtmVplEntry 32 } ciscoAtmVplLsPerVcqWrrWeight OBJECT-TYPE SYNTAX INTEGER (1..15) MAX-ACCESS read-write STATUS current DESCRIPTION "Configure the weighting specified for a VP half-leg within a service class to make the scheduling decision among other active VPLs in the service class. This is for transmit on the VPL on the interface. This parameter only applies to transit VPs. This object is defined only when the switch is equipped with the Lightstream per-VC queueing chipset." ::= { ciscoAtmVplEntry 33 } ciscoAtmVplLsPerVcqTunnelIsShaped OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Determines whether this is to be a -shaped- VP, per the Lightstream per-VC queueing chipset. If the value specified is TRUE, the VP is to be a shaped VP Tunnel. Such a VP cannot be cross-connected. This object is defined only when the switch is equipped with the Lightstream per-VC queueing chipset." ::= { ciscoAtmVplEntry 34 } ciscoAtmVplLsPerVcqXmtQueuedCells OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of cells received on this VPL and residing on the per-connection queue. Note that this value is not valid until the VPL is in an active cross-connect. This object is defined only when the switch is equipped with the Lightstream per-VC queueing chipset." ::= { ciscoAtmVplEntry 35 } ciscoAtmVplLsPerVcQThreshGrp OBJECT-TYPE SYNTAX LsPerVcqThresholdGroup MAX-ACCESS read-only STATUS current DESCRIPTION "The Threshold Group to which the cell-queue for cells received by this VP are queued. This object is defined only when the switch is equipped with the Lightstream per-VC queueing chipset." ::= { ciscoAtmVplEntry 36 } ciscoAtmVplInClp0Cells OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of cells with the CLP bit clear received on this VPL. Note that these cells may subsequently be discarded. This counter is valid only: - if the VPL is not a Logical Interface (tunnel). - on LS1010 systems, only those equipped with Feature Card - Per Flow Queueing." ::= { ciscoAtmVplEntry 37 } ciscoAtmVplInClp1Cells OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of cells with the CLP bit set received on this VPL. Note that these cells may subsequently be discarded. This counter is valid only: - if the VPL is not a Logical Interface (tunnel). - on LS1010 systems, only those equipped with Feature Card - Per Flow Queueing." ::= { ciscoAtmVplEntry 38 } ciscoAtmVplOutClp0Cells OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of cells with the CLP bit clear transmitted on this VPL. This counter is valid only: - if the VPL is not a Logical Interface (tunnel). - on LS1010 systems, only those equipped with the Feature Card - Per Flow Queueing." ::= { ciscoAtmVplEntry 39 } ciscoAtmVplOutClp1Cells OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of cells with the CLP bit set transmitted on this VPL. This counter is valid only: - if the VPL is not a Logical Interface (tunnel). - on LS1010 systems, only those equipped with the Feature Card - Per Flow Queueing." ::= { ciscoAtmVplEntry 40 } ciscoAtmVplCellDrops OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of cells received on this VPL, but discarded. This counter is valid only: - if the VPL is not a Logical Interface (tunnel). - on LS1010 systems, only those equipped with Feature Card - Per Flow Queueing." ::= { ciscoAtmVplEntry 41 } ciscoAtmVplClp0VcqFullCellDrops OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of cells received on this VPL with the CLP bit clear, discarded because the per-VC queue limit is exceeded. This counter is valid only: - if the VPL is not a Logical Interface (tunnel). - on LS1010 systems, only those equipped with Feature Card - Per Flow Queueing." ::= { ciscoAtmVplEntry 43 } ciscoAtmVplVcqClpThreshCellDrops OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of cells received on this VPL, discarded because the discard threshold (as opposed to the queue-limit) is exceeded on the per-VC queue, and the CLP bit is set. This counter is valid only: - if the VPL is not a Logical Interface (tunnel). - on LS1010 systems, only those equipped with Feature Card - Per Flow Queueing." ::= { ciscoAtmVplEntry 44 } ciscoAtmVplLsPerVcqTunnelIsHierarchical OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Determines whether this is to be a -Hierarchical- VP, per the Lightstream per-VC queueing chipset. If the value specified is TRUE, the VP is to be a Hierarchical VP Tunnel. Such a VP cannot be cross-connected. This object is defined on a LS1010 only when the switch is equipped with the Lightstream per-VC queueing chipset." ::= { ciscoAtmVplEntry 45 } ciscoAtmVplRxNegTraffDescrIndex OBJECT-TYPE SYNTAX AtmTrafficDescrParamIndex MAX-ACCESS read-only STATUS current DESCRIPTION "Identifies the entry in the atmTrafficDescrParamTable which contains negotiated traffic parameters applied to the receive direction of this VPL. This object is not instantiated if this VPL is not the calling side of a soft VP, or if there was no traffic negotiation." ::= { ciscoAtmVplEntry 46} ciscoAtmVplTxNegTraffDescrIndex OBJECT-TYPE SYNTAX AtmTrafficDescrParamIndex MAX-ACCESS read-only STATUS current DESCRIPTION "Identifies the entry in the atmTrafficDescrParamTable which contains negotiated traffic parameters applied to the transmit direction of this VPL. This object is not instantiated if this VPL is not the calling side of a soft VP, or if there was no traffic negotiation." ::= { ciscoAtmVplEntry 47} ciscoAtmVplSwFabOutCells OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of cells transmitted on this VPL by the Switch Fabric. This object is not instantiated on systems that do not have support for collecting such statistics." ::= { ciscoAtmVplEntry 48 } ciscoAtmVplSwFabOutClp0Cells OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of cells with the CLP bit clear transmitted on this VPL by the Switch Fabric. This object is not instantiated for a VPL that is a logical interface (VP Tunnel). This object is not instantiated on systems that do not have support for collecting such statistics." ::= { ciscoAtmVplEntry 49 } ciscoAtmVplSwFabOutClp1Cells OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of cells with the CLP bit set transmitted on this VPL by the Switch Fabric. This object is not instantiated for a VPL that is a logical interface (VP Tunnel). This object is not instantiated on systems that do not have support for collecting such statistics." ::= { ciscoAtmVplEntry 50 } ciscoAtmVplConnName OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-write STATUS current DESCRIPTION "A human readable string that identifies this connection. This object will return a zero-length string if value is not set." ::= { ciscoAtmVplEntry 51 } ciscoAtmVplConnType OBJECT-TYPE SYNTAX INTEGER { local (1), -- within a node endToEnd (2) -- across several nodes } MAX-ACCESS read-write STATUS current DESCRIPTION "This object represent the PVP Type for this connection. - local connection within the node - endToEnd across several nodes This object serves as an information object for a management system and has no functional meaning to the switch." ::= { ciscoAtmVplEntry 52 } -- This group is an extension of VCL table ciscoAtmVcl OBJECT IDENTIFIER ::= { ciscoAtmConnMIBObjects 2 } ciscoAtmVclTable OBJECT-TYPE SYNTAX SEQUENCE OF CiscoAtmVclEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The Virtual Channel Link extension Table." ::= { ciscoAtmVcl 1 } ciscoAtmVclEntry OBJECT-TYPE SYNTAX CiscoAtmVclEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " An entry in the Vcl table.This entry is used to model a bi-directional Vcl. This table augments the atmVclTable defined in RFC 1695. However it uses ifIndex, atmVclVpi and atmVclVci as an Index for historical reasons. The entries are created/deleted as a by-product of creating and deleting entries in the atmVclTable." INDEX { ifIndex,atmVclVpi,atmVclVci } ::= { ciscoAtmVclTable 1 } CiscoAtmVclEntry ::= SEQUENCE { -- config info ciscoAtmVclCastType CastType, ciscoAtmVclSpanType SpanType, ciscoAtmVclConfigType ConfigType, ciscoAtmVclRxUpcMode UpcStatus, ciscoAtmVclEpdEnable INTEGER, -- connection state ciscoAtmVclConnState ConnState, -- oam config info ciscoAtmVclOamLoopbkTxInterval Integer32, ciscoAtmVclOamSegmentLoopback EnableStatus, ciscoAtmVclOamEndLoopback EnableStatus, ciscoAtmVclOamAisEnable EnableStatus, ciscoAtmVclOamRdiEnable EnableStatus, -- per vc statistics ciscoAtmVclInstallTime TimeStamp, ciscoAtmVclInCells Counter32, ciscoAtmVclOutCells Counter32, -- cross side connection info ciscoAtmVclCrossIfIndex InterfaceIndexOrZero, ciscoAtmVclCrossVpi Integer32, ciscoAtmVclCrossVci Integer32, ciscoAtmVclNextLeafIfIndex InterfaceIndexOrZero, ciscoAtmVclNextLeafVpi Integer32, ciscoAtmVclNextLeafVci Integer32, -- vc terminating info ciscoAtmVclAalEncapFlag INTEGER, ciscoAtmVclAalEncapProtocol INTEGER, ciscoAtmVclAalUserVcType INTEGER, ciscoAtmVclAtmInArpInterval Integer32, -- soft PVC ciscoAtmVclRemoteAddr NsapAtmAddr, ciscoAtmVclRemoteVpi Integer32, ciscoAtmVclRemoteVci Integer32, ciscoAtmVclLocation Location, ciscoAtmVclSlowRetryIntv Integer32, ciscoAtmVclNumAttempts Counter32, ciscoAtmVclLastReleaseCause Integer32, -- per vc violation stats ciscoAtmVclUpcViolations Counter32, ciscoAtmVclEpdTpdCellDrops Counter32, ciscoAtmVclEpdTpdPacketDrops Counter32, ciscoAtmVclEpdTpdPacketsIn Counter32, ciscoAtmVclClp1Drops Counter32, -- default tolerance ciscoAtmVclDefaultRxUpcTolerance Integer32, ciscoAtmVclDefaultRxUpcVbrCdvt Integer32, -- lightstream per-vc queueing -- switch chipset objects ciscoAtmVclLsPerVcqWrrWeight INTEGER, ciscoAtmVclLsPerVcqXmtQueuedCells Gauge32, ciscoAtmVclLsPerVcQThreshGrp LsPerVcqThresholdGroup, -- feature card per-flow queueing -- (FC-PFQ) per-VCL statistics objects ciscoAtmVclInClp0Cells Counter32, ciscoAtmVclInClp1Cells Counter32, ciscoAtmVclOutClp0Cells Counter32, ciscoAtmVclOutClp1Cells Counter32, ciscoAtmVclCellDrops Counter32, ciscoAtmVclClp0VcqFullCellDrops Counter32, ciscoAtmVclVcqClpThreshCellDrops Counter32, -- Objects for negotiated traffic parameters ciscoAtmVclRxNegTraffDescrIndex AtmTrafficDescrParamIndex, ciscoAtmVclTxNegTraffDescrIndex AtmTrafficDescrParamIndex, -- Switch Fabric Tx Statistics ciscoAtmVclSwFabOutCells Counter32, ciscoAtmVclSwFabOutClp0Cells Counter32, ciscoAtmVclSwFabOutClp1Cells Counter32, -- Connection Info ciscoAtmVclConnName SnmpAdminString, ciscoAtmVclConnType INTEGER } ciscoAtmVclCastType OBJECT-TYPE SYNTAX CastType MAX-ACCESS read-write STATUS current DESCRIPTION " Vcl type is either a point to point connection or point to multipoint root or leaf." DEFVAL {pointToPoint } ::= { ciscoAtmVclEntry 1 } ciscoAtmVclSpanType OBJECT-TYPE SYNTAX SpanType MAX-ACCESS read-only STATUS current DESCRIPTION " Vcl span is either a transit one or a terminating one." DEFVAL { transit } ::= { ciscoAtmVclEntry 2 } ciscoAtmVclConfigType OBJECT-TYPE SYNTAX ConfigType MAX-ACCESS read-write STATUS current DESCRIPTION " Vcl type is either a PVC, SVC, Soft PVC or Soft Passive half leg. The half leg can be set to Passive through user configuration only." DEFVAL { permanent } ::= { ciscoAtmVclEntry 3 } ciscoAtmVclRxUpcMode OBJECT-TYPE SYNTAX UpcStatus MAX-ACCESS read-write STATUS current DESCRIPTION " Usage Parameter Control opeartion is pass,tag,drop or local shaping at this connection." DEFVAL { passing } ::= { ciscoAtmVclEntry 4 } ciscoAtmVclEpdEnable OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2), useTrafficDescr(3) } MAX-ACCESS read-write STATUS current DESCRIPTION " Early Packet Discard option used for this VCL. The use is as follows: enable(1) Packet-discard is enabled. disable(2) Packet-discard is disabled. useTrafficDescr(3) Packet-discard in the receive direction is as specified by the atmTrafficFrameDiscard value in row corresponding to atmVclReceiveTrafficDescrIndex. For VCLs of type spvcInitiator, the packet-discard in the reverse direction is as specified by the atmTrafficFrameDiscard value in row corresponding to atmVclTransmitTrafficDescrIndex. " DEFVAL { useTrafficDescr } ::= { ciscoAtmVclEntry 5 } ciscoAtmVclConnState OBJECT-TYPE SYNTAX ConnState MAX-ACCESS read-write STATUS current DESCRIPTION "The connection state of this VCL." ::= { ciscoAtmVclEntry 6 } ciscoAtmVclOamLoopbkTxInterval OBJECT-TYPE SYNTAX Integer32 (5..60) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "Frequency of OAM loopback cell are generated on this virtual channel." DEFVAL { 5 } ::= { ciscoAtmVclEntry 7 } ciscoAtmVclOamSegmentLoopback OBJECT-TYPE SYNTAX EnableStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Enable segment loopback on this virtual channel." DEFVAL { disable } ::= { ciscoAtmVclEntry 8 } ciscoAtmVclOamEndLoopback OBJECT-TYPE SYNTAX EnableStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Enable end to end loopback on this virtual channel." DEFVAL { disable } ::= { ciscoAtmVclEntry 9 } ciscoAtmVclOamAisEnable OBJECT-TYPE SYNTAX EnableStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Enable Alarm Indication Signal OAM cell generation if the interafce goes down on a crossconnect virtual channel." DEFVAL { disable } ::= { ciscoAtmVclEntry 10 } ciscoAtmVclOamRdiEnable OBJECT-TYPE SYNTAX EnableStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Enable Remote Defect Indication OAM cell generation if an Alarm Indication Signal OAM cell is received." DEFVAL { disable } ::= { ciscoAtmVclEntry 11 } ciscoAtmVclInstallTime OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "The time stamp derived from sysUpTime when this VCL gets created. The VCL entries are created/deleted as a by-product of creating and deleting entries in the atmVclTable defined in RFC1695." ::= { ciscoAtmVclEntry 12 } ciscoAtmVclInCells OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of cells received on this VCL." ::= { ciscoAtmVclEntry 13 } ciscoAtmVclOutCells OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of cells transmitted on this VCL." ::= { ciscoAtmVclEntry 14 } ciscoAtmVclCrossIfIndex OBJECT-TYPE SYNTAX InterfaceIndexOrZero MAX-ACCESS read-write STATUS current DESCRIPTION "For point to point, this is the cross-connected VCL's ifIndex of this VCL. For point to multi-point connection, this will be the root VCL's ifIndex for a leaf VCL entry in the multicast chain, or it's the 1st leaf VCL for a root VCL entry. If it's zero, it means it's not cross-connected yet. Atomically set ciscoAtmVclConnState, ciscoAtmVclCrossIfindex, ciscoAtmVclCrossVpi and ciscoAtmVclCrossVci will create or delete a cross connection to crossed half leg of this ciscoAtmVclCrossIfindex, ciscoAtmVclCrossVpi and ciscoAtmVclCrossVci for p2p PVC, or add or drop a multicast connection to/from the root of this ciscoAtmVclCrossIfindex, ciscoAtmVclCrossVpi and ciscoAtmVclCrossVci on the multicast chain for p2mp PVC." DEFVAL { 0 } ::= { ciscoAtmVclEntry 15 } ciscoAtmVclCrossVpi OBJECT-TYPE SYNTAX Integer32 (0..4095) MAX-ACCESS read-write STATUS current DESCRIPTION "This specifies the VPI value of the VCL to which this VCL is cross-connected. For point to multi-point connection, this is the root VCL's VPI for the leaf entry. Similarly it is the 1st leaf's VPI value for the root entry." DEFVAL { 0 } ::= { ciscoAtmVclEntry 16 } ciscoAtmVclCrossVci OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "This specifies the VCI value of the VCL to which this VCL is cross-connected. For point to multi-point connection, this is the root VCL's VCI for the leaf entry. Similarly it is the 1st leaf's VCI value for the root entry." DEFVAL { 0 } ::= { ciscoAtmVclEntry 17 } ciscoAtmVclNextLeafIfIndex OBJECT-TYPE SYNTAX InterfaceIndexOrZero MAX-ACCESS read-only STATUS current DESCRIPTION "For point to point, this is zero i.e. not used. For point to multi-point connection, this will be the next leaf VCL's ifIndex on the multicast chain. This will be 0 if this is the root VCL entry. If it's zero for a leaf VCL, it means this is the last leaf." DEFVAL { 0 } ::= { ciscoAtmVclEntry 18 } ciscoAtmVclNextLeafVpi OBJECT-TYPE SYNTAX Integer32 (0..4095) MAX-ACCESS read-only STATUS current DESCRIPTION "For point to point, this is zero i.e. not used. This apply only to point to multi-point connection, this will be the next leaf VCL's VPI on the multicast chain." DEFVAL { 0 } ::= { ciscoAtmVclEntry 19 } ciscoAtmVclNextLeafVci OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "For point to point, this is zero i.e. not used. This apply only to point to multi-point connection, this will be the next leaf VCL's VCI on the multicast chain." DEFVAL { 0 } ::= { ciscoAtmVclEntry 20 } ciscoAtmVclAalEncapFlag OBJECT-TYPE SYNTAX INTEGER { other(1), aal5Snap(2), aal5Nlpid(3), aal5FrNlpid(4), aal5Mux(5), aal34Smds(6), aalQsAal(7), -- Signalling AAL aal5Ilmi(8), aal5Lane(9), aal5Pnni(10) } MAX-ACCESS read-write STATUS current DESCRIPTION "Encapsulation type for terminating VC." ::= { ciscoAtmVclEntry 21 } ciscoAtmVclAalEncapProtocol OBJECT-TYPE SYNTAX INTEGER { other(1), ip(2), xns(3), appletalk(4), clns(5), decnet(6), novell(7), apollo(8), vines(9) } MAX-ACCESS read-write STATUS current DESCRIPTION "Protocol for terminating VC if EncapFlag is aal5Mux." ::= { ciscoAtmVclEntry 22 } ciscoAtmVclAalUserVcType OBJECT-TYPE SYNTAX INTEGER { other(1), boxConfigure(2), busForward(3), busSend(4), clientConfigure(5), clientData(6), clientDirect(7), clientDistribute(8), clientForward(9), clientSend(10), configure(11), serverConfigure(12), serverDirect(13), serverDistribute(14) } MAX-ACCESS read-write STATUS current DESCRIPTION "Following is the list of user virtual circuit types in case aal5Lane encapusation on this virtual channel. boxConfigure -- The shared Server/Client end of a Configure VCC busForward -- The BUS end of the Data Forward VCC busSend -- The BUS end of the Data Send VCC clientConfigure -- The LE Client end of the Configure Direct VCC clientData -- One end of the Data Direct VCC clientDirect -- The LE Client end of the Control Direct VCC clientDistribute -- The LE Client end of the Control Distribute VCC clientForward -- The LE Client end of the Multicast Forward VCC clientSend -- The LE Client end of the Multicast Send VCC configure -- The Config Server end of any Configure VCC serverConfigure -- The LE Server end of the Configure VCC serverDirect -- The LE Server end of the Control Direct VCC." ::= { ciscoAtmVclEntry 23 } ciscoAtmVclAtmInArpInterval OBJECT-TYPE SYNTAX Integer32 (0..60) UNITS "minutes" MAX-ACCESS read-write STATUS current DESCRIPTION "Time interval in minutes to send InArp on a PVC for IP over ATM. 0 will disable the InArp for this pvc." ::= { ciscoAtmVclEntry 24 } ciscoAtmVclRemoteAddr OBJECT-TYPE SYNTAX NsapAtmAddr MAX-ACCESS read-write STATUS current DESCRIPTION "Soft PVC target address if this is the calling side Soft PVC source address if this is called side. Atomically set ConnState, RemoteAddr, RemoteVpi and RemoteVci will create or delete a soft PVC. Atomically set ConnState, RemoteAddr without RemoteVpi, Remote Vci will also create or delete a soft PVC but let target switch assign the vpi and vci." ::= { ciscoAtmVclEntry 25 } ciscoAtmVclRemoteVpi OBJECT-TYPE SYNTAX Integer32 (0..4095) MAX-ACCESS read-write STATUS current DESCRIPTION "Soft PVC target VPI in calling side. 0 in called side." ::= { ciscoAtmVclEntry 26 } ciscoAtmVclRemoteVci OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "Soft PVC target VCI in calling side. 0 in called side." ::= { ciscoAtmVclEntry 27 } ciscoAtmVclLocation OBJECT-TYPE SYNTAX Location MAX-ACCESS read-only STATUS current DESCRIPTION "Indicate calling or called side of a soft PVC. If ciscoAtmVclConfigType is not soft then ciscoAtmVclLocation value should be ignored." ::= { ciscoAtmVclEntry 28 } ciscoAtmVclSlowRetryIntv OBJECT-TYPE SYNTAX Integer32 (0..65535) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "Soft PVC slow retry interval in seconds." ::= { ciscoAtmVclEntry 29 } ciscoAtmVclNumAttempts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of retries made to install this soft PVC connection. If ciscoAtmVclConfigType is not soft then ciscoAtmVclNumAttempts value should be ignored." ::= { ciscoAtmVclEntry 30 } ciscoAtmVclLastReleaseCause OBJECT-TYPE SYNTAX Integer32(1..127) MAX-ACCESS read-only STATUS current DESCRIPTION "Value of the Cause field of the Cause Information Element in the last Release Signalling message received for this SPVC. Indicates the reason for the Release. ciscoAtmVclConfigType is not soft then ciscoAtmVclLastReleaseCause value should be ignored." ::= { ciscoAtmVclEntry 31 } ciscoAtmVclUpcViolations OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of nonconforming cells detected by Usage Parameter Control (UPC) for cells received on this VCL. On LS1010 systems, this counter is valid only on those equipped with the Feature Card - Per Flow Queueing." ::= { ciscoAtmVclEntry 32 } ciscoAtmVclEpdTpdCellDrops OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS obsolete DESCRIPTION "Never implemented." ::= { ciscoAtmVclEntry 33 } ciscoAtmVclEpdTpdPacketDrops OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of EPD/TPD packet drops of packets received on this VCL. This counter is valid only: - if EPD is enabled on this VCL. - on LS1010 systems, only those equipped with the Feature Card - Per Flow Queueing." ::= { ciscoAtmVclEntry 34 } ciscoAtmVclEpdTpdPacketsIn OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of packets received in their entirety on this VPL. This counter is valid only: - if EPD is enabled on this VCL. - on LS1010 systems, only those equipped with the Feature Card - Per Flow Queueing." ::= { ciscoAtmVclEntry 35 } ciscoAtmVclClp1Drops OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS obsolete DESCRIPTION "Never implemented." ::= { ciscoAtmVclEntry 37 } ciscoAtmVclDefaultRxUpcTolerance OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "If the tolerance (CDVT for CBR, ABR, UBR connections, Maximum Burst Size for VBR connectons) requested for Usage Parameter Control is not explicitly specified in VCL creation, this object contains the default that is used.If tolerance is explicitly specified in VCL creation, it can be found in the Traffic Table row specified by atmVclReceiveTrafficDescrIndex, and the value of this object is -1." ::= { ciscoAtmVclEntry 38 } ciscoAtmVclDefaultRxUpcVbrCdvt OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "If the Cell Delay Variation Tolerance (CDVT) requested for Usage Parameter Control for a VBR connection is not explicitly specified in VCL creation, this object contains the default that is used. If CDVT is explicitly specified in VCL creation, it can be found in the Traffic Table row specified by atmVclReceiveTrafficDescrIndex, and the value of this object is -1." ::= { ciscoAtmVclEntry 39 } ciscoAtmVclLsPerVcqWrrWeight OBJECT-TYPE SYNTAX INTEGER (1..15) MAX-ACCESS read-write STATUS current DESCRIPTION "Configure the weighting specified for a VC half-leg within a service class to make the scheduling decision among other active VCLs in the service class. This is for transmit on the VCL on the interface. This object is defined only when the switch is equipped with the Lightstream per-VC queueing chipset." ::= { ciscoAtmVclEntry 40 } ciscoAtmVclLsPerVcqXmtQueuedCells OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of cells received on this VCL and residing on the per-connection queue. Note that this value is not valid until the VCL is in an active cross-connect. This object is defined only when the switch is equipped with the Lightstream per-VC queueing chipset." ::= { ciscoAtmVclEntry 41 } ciscoAtmVclLsPerVcQThreshGrp OBJECT-TYPE SYNTAX LsPerVcqThresholdGroup MAX-ACCESS read-only STATUS current DESCRIPTION "The Threshold Group to which the cell-queue for cells received by this VC are queued. Note that this value is not valid until the VCL is in an active cross-connect. This object is defined only when the switch is equipped with the Lightstream per-VC queueing chipset." ::= { ciscoAtmVclEntry 42 } ciscoAtmVclInClp0Cells OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of cells with the CLP bit clear received on this VCL. Note that these cells may subsequently be discarded. This counter is valid only: - on LS1010 systems, only those equipped with Feature Card - Per Flow Queueing." ::= { ciscoAtmVclEntry 43 } ciscoAtmVclInClp1Cells OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of cells with the CLP bit set received on this VCL. Note that these cells may subsequently be discarded. This counter is valid only: - on LS1010 systems, only those equipped with Feature Card - Per Flow Queueing." ::= { ciscoAtmVclEntry 44 } ciscoAtmVclOutClp0Cells OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of cells with the CLP bit clear transmitted on this VCL. This counter is valid only: - on LS1010 systems, only those equipped with Feature Card - Per Flow Queueing." ::= { ciscoAtmVclEntry 45 } ciscoAtmVclOutClp1Cells OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of cells with the CLP bit set transmitted on this VCL. This counter is valid only: - on LS1010 systems, only those equipped with Feature Card - Per Flow Queueing." ::= { ciscoAtmVclEntry 46 } ciscoAtmVclCellDrops OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of cells received on this VCL, but discarded. This counter is valid only: - on LS1010 systems, only those equipped with Feature Card - Per Flow Queueing." ::= { ciscoAtmVclEntry 47 } ciscoAtmVclClp0VcqFullCellDrops OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of cells received on this VCL with the CLP bit clear, discarded because the per-VC queue limit is exceeded. This counter is valid only: - if EPD is disabled on the VCL. - on LS1010 systems, only those equipped with Feature Card - Per Flow Queueing." ::= { ciscoAtmVclEntry 48 } ciscoAtmVclVcqClpThreshCellDrops OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of cells received on this VCL, discarded because the discard threshold (as opposed to the queue-limit) is exceeded on the per-VC queue, and the CLP bit is set. This counter is valid only: - if EPD is disabled on the VCL. - on LS1010 systems, only those equipped with Feature Card - Per Flow Queueing." ::= { ciscoAtmVclEntry 49 } ciscoAtmVclRxNegTraffDescrIndex OBJECT-TYPE SYNTAX AtmTrafficDescrParamIndex MAX-ACCESS read-only STATUS current DESCRIPTION "Identifies the entry in the atmTrafficDescrParamTable which contains negotiated traffic parameters applied to the receive direction of this VCL. This object is not instantiated if this VCL is not the calling side of a soft VC, or if there was no traffic negotiation." ::= { ciscoAtmVclEntry 50} ciscoAtmVclTxNegTraffDescrIndex OBJECT-TYPE SYNTAX AtmTrafficDescrParamIndex MAX-ACCESS read-only STATUS current DESCRIPTION "Identifies the entry in the atmTrafficDescrParamTable which contains negotiated traffic parameters applied to the transmit direction of this VCL. This object is not instantiated if this VCL is not the calling side of a soft VC, or if there was no traffic negotiation." ::= { ciscoAtmVclEntry 51} ciscoAtmVclSwFabOutCells OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of cells transmitted on this VCL by the Switch Fabric. This object is not instantiated on systems that do not have support for collecting such statistics." ::= { ciscoAtmVclEntry 52 } ciscoAtmVclSwFabOutClp0Cells OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of cells with the CLP bit clear transmitted on this VCL by the Switch Fabric. This object is not instantiated on systems that do not have support for collecting such statistics." ::= { ciscoAtmVclEntry 53 } ciscoAtmVclSwFabOutClp1Cells OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of cells with the CLP bit set transmitted on this VCL by the Switch Fabric. This object is not instantiated on systems that do not have support for collecting such statistics." ::= { ciscoAtmVclEntry 54 } ciscoAtmVclConnName OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-write STATUS current DESCRIPTION "A human readable string that identifies this connection. This object will return a zero-length string if value is not set." ::= { ciscoAtmVclEntry 55 } ciscoAtmVclConnType OBJECT-TYPE SYNTAX INTEGER { local (1), -- wthin a node endToEnd (2) -- across several nodes } MAX-ACCESS read-write STATUS current DESCRIPTION "This object represent the PVC Type for this connection. - local connection within the node - endToEnd across several nodes. This object serves as an information object for a management system and has no functional meaning to the switch." ::= { ciscoAtmVclEntry 56 } -- SVP address table ciscoAtmSvp OBJECT IDENTIFIER ::= { ciscoAtmConnMIBObjects 3 } ciscoAtmSvpAddrTable OBJECT-TYPE SYNTAX SEQUENCE OF CiscoAtmSvpAddrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Switched virtual path link address table." ::= { ciscoAtmSvp 1 } ciscoAtmSvpAddrEntry OBJECT-TYPE SYNTAX CiscoAtmSvpAddrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " An entry in the Switched Vrtual Path address table." INDEX { ifIndex,ciscoAtmSvpAddr, ciscoAtmSvpVpi } ::= { ciscoAtmSvpAddrTable 1 } CiscoAtmSvpAddrEntry ::= SEQUENCE { ciscoAtmSvpAddr OCTET STRING, ciscoAtmSvpVpi INTEGER, ciscoAtmSvpDirection Direction } ciscoAtmSvpAddr OBJECT-TYPE SYNTAX OCTET STRING (SIZE(20)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "It depends on the direction.This could be p2pCallingSide address on a called side VPL, or p2pCalledSide address on a calling side VPL or p2mpRoot address on a p2mp leaf side VPL or p2mpLeaf address on a p2mp root side VPL." ::= { ciscoAtmSvpAddrEntry 1 } ciscoAtmSvpVpi OBJECT-TYPE SYNTAX INTEGER (1..4095) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This SVP's VPI value on this interface." ::= { ciscoAtmSvpAddrEntry 2 } ciscoAtmSvpDirection OBJECT-TYPE SYNTAX Direction MAX-ACCESS read-only STATUS current DESCRIPTION "Indicate whether this VPL is calling side, called side, root or leaf for this address." ::= { ciscoAtmSvpAddrEntry 3 } -- SVC address table ciscoAtmSvc OBJECT IDENTIFIER ::= { ciscoAtmConnMIBObjects 4 } ciscoAtmSvcAddrTable OBJECT-TYPE SYNTAX SEQUENCE OF CiscoAtmSvcAddrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Switched virtual channel link address table." ::= { ciscoAtmSvc 1 } ciscoAtmSvcAddrEntry OBJECT-TYPE SYNTAX CiscoAtmSvcAddrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " An entry in the SVC address table." INDEX { ifIndex,ciscoAtmSvcAddr, ciscoAtmSvcVpi, ciscoAtmSvcVci } ::= { ciscoAtmSvcAddrTable 1 } CiscoAtmSvcAddrEntry ::= SEQUENCE { ciscoAtmSvcAddr OCTET STRING , ciscoAtmSvcVpi Integer32, ciscoAtmSvcVci Integer32, ciscoAtmSvcDirection Direction } ciscoAtmSvcAddr OBJECT-TYPE SYNTAX OCTET STRING (SIZE(20)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "It depends on the direction.This could be p2pCallingSide address on a called side VCL, or p2pCalledSide address on a calling side VCL or p2mpRoot address on a p2mp leaf side VCL or p2mpLeaf address on a p2mp root side VCL." ::= { ciscoAtmSvcAddrEntry 1 } ciscoAtmSvcVpi OBJECT-TYPE SYNTAX Integer32 (0..4095) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This SVC's VPI value on this interface." ::= { ciscoAtmSvcAddrEntry 2 } ciscoAtmSvcVci OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This SVC's VCI value on this interface." ::= { ciscoAtmSvcAddrEntry 3 } ciscoAtmSvcDirection OBJECT-TYPE SYNTAX Direction MAX-ACCESS read-only STATUS current DESCRIPTION "Indicate whether this VCL is calling side, called side, root or leaf for this address." ::= { ciscoAtmSvcAddrEntry 4 } -- Snoop VC Table for per-VC snooping -- keeps the corresponding snooped interface, snooped vpi, snooped vci -- snooping direction ciscoAtmSnoopVc OBJECT IDENTIFIER ::= { ciscoAtmConnMIBObjects 5 } ciscoAtmSnoopVcTable OBJECT-TYPE SYNTAX SEQUENCE OF CiscoAtmSnoopVcEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Snooping VC Table." ::= { ciscoAtmSnoopVc 1 } ciscoAtmSnoopVcEntry OBJECT-TYPE SYNTAX CiscoAtmSnoopVcEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the Snoop VC table. This entry models a VC snooping connection. The ifIndex indicates the snooping interface, the atmVclVpi and atmVclVci specifies the VPI and VCI value of the snooping connection. To create or destroy a snooping connection at an ATM interface, the following procedures are used: Configure VC Snooping A snooping connection is configured in one step by a set-request with all necessary snoop parameter values and set-request to the object ciscoAtmSnoopVcRowStatus to createAndGo(4). This may fail for the following reasons: - The selected snooping VPI/VCI values are unavailable, - The selected snooping VPI/VCI values are in use. - The selected snooping interface is CPU interface. - The selected snooped connection doesn't exist. - There is no traffic in the selected snoop direction. - Resource failure during configuration of snooping connection. De-Configure VC Snooping A snooping connection is deconfigured by a set-request to the object ciscoAtmSnoopVcRowStatus to destroy(6), and the agent releases all associated resources." INDEX { ifIndex, atmVclVpi, atmVclVci } ::= { ciscoAtmSnoopVcTable 1 } CiscoAtmSnoopVcEntry ::= SEQUENCE { ciscoAtmSnoopVcSnoopedIfIndex InterfaceIndexOrZero, ciscoAtmSnoopVcSnoopedVpi Integer32, ciscoAtmSnoopVcSnoopedVci Integer32, ciscoAtmSnoopVcDir SnoopDirType, ciscoAtmSnoopVcState ConnState, ciscoAtmSnoopVcRowStatus RowStatus } ciscoAtmSnoopVcSnoopedIfIndex OBJECT-TYPE SYNTAX InterfaceIndexOrZero MAX-ACCESS read-create STATUS current DESCRIPTION "This specifies the ifIndex of the snooped interface." DEFVAL { 0 } ::= { ciscoAtmSnoopVcEntry 1 } ciscoAtmSnoopVcSnoopedVpi OBJECT-TYPE SYNTAX Integer32 (0..4095) MAX-ACCESS read-create STATUS current DESCRIPTION "This specifies the VPI value of the snooped connection endpoint." DEFVAL { 0 } ::= { ciscoAtmSnoopVcEntry 2 } ciscoAtmSnoopVcSnoopedVci OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-create STATUS current DESCRIPTION "This specifies the VCI value of the snooped connection endpoint." DEFVAL { 0 } ::= { ciscoAtmSnoopVcEntry 3} ciscoAtmSnoopVcDir OBJECT-TYPE SYNTAX SnoopDirType MAX-ACCESS read-create STATUS current DESCRIPTION "This specifies the traffic direction at the snooped connection endpoint." DEFVAL { receive } ::= { ciscoAtmSnoopVcEntry 4 } ciscoAtmSnoopVcState OBJECT-TYPE SYNTAX ConnState MAX-ACCESS read-only STATUS current DESCRIPTION "The connection state of this Snooping connetion." ::= { ciscoAtmSnoopVcEntry 5 } ciscoAtmSnoopVcRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to create a new row or delete an existing row in this table. This gives the way to configure one-shot per-vc snooping connection" DEFVAL { active } ::= { ciscoAtmSnoopVcEntry 6} -- Snoop VP Table, for per-VP snooping -- keeps the corresponding snooped interface, snooped vpi -- and snooping direction ciscoAtmSnoopVp OBJECT IDENTIFIER ::= { ciscoAtmConnMIBObjects 6 } ciscoAtmSnoopVpTable OBJECT-TYPE SYNTAX SEQUENCE OF CiscoAtmSnoopVpEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Snooping VP Table." ::= { ciscoAtmSnoopVp 1 } ciscoAtmSnoopVpEntry OBJECT-TYPE SYNTAX CiscoAtmSnoopVpEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the Snoop VP table. This entry models a VP snooping connection. The ifIndex indicates the snooping interface, the atmVclVpi specifies the VPI value of the snooping connection. To create or destroy a snooping connection at an ATM interface, the following procedures are used: Configure VP Snooping A snooping connection is configured in one step by a set-request with all necessary snoop parameter values and set-request to the object ciscoAtmSnoopVpRowStatus to createAndGo(4). This may fail for the following reasons: - The selected snooping VPI values are unavailable, - The selected snooping VPI values are in use. - The selected snooping interface is CPU interface. - The selected snooped connection doesn't exist. - There is no traffic in the selected snoop direction. - Resource failure during configuration of snooping connection. De-Configure VP Snooping A snooping connection is deconfigured by a set-request to the object ciscoAtmSnoopVpRowStatus to destroy(6), and the agent releases all associated resources." INDEX { ifIndex, atmVplVpi } ::= { ciscoAtmSnoopVpTable 1 } CiscoAtmSnoopVpEntry ::= SEQUENCE { ciscoAtmSnoopVpSnoopedIfIndex InterfaceIndexOrZero, ciscoAtmSnoopVpSnoopedVpi Integer32, ciscoAtmSnoopVpDir SnoopDirType, ciscoAtmSnoopVpState ConnState, ciscoAtmSnoopVpRowStatus RowStatus } ciscoAtmSnoopVpSnoopedIfIndex OBJECT-TYPE SYNTAX InterfaceIndexOrZero MAX-ACCESS read-create STATUS current DESCRIPTION "This specifies the ifIndex of the snooped interface." DEFVAL { 0 } ::= { ciscoAtmSnoopVpEntry 1 } ciscoAtmSnoopVpSnoopedVpi OBJECT-TYPE SYNTAX Integer32 (0..4095) MAX-ACCESS read-create STATUS current DESCRIPTION "This specifies the VPI value of the snooped connection endpoint." DEFVAL { 0 } ::= { ciscoAtmSnoopVpEntry 2 } ciscoAtmSnoopVpDir OBJECT-TYPE SYNTAX SnoopDirType MAX-ACCESS read-create STATUS current DESCRIPTION "This specifies the traffic direction at the snooped connection endpoint." DEFVAL { receive } ::= { ciscoAtmSnoopVpEntry 3 } ciscoAtmSnoopVpState OBJECT-TYPE SYNTAX ConnState MAX-ACCESS read-only STATUS current DESCRIPTION "The connection state of this Snooping connection ." ::= { ciscoAtmSnoopVpEntry 4 } ciscoAtmSnoopVpRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to create a new row or delete an existing row in this table. This gives the way to configure one-shot per-vp snooping connection" DEFVAL { active } ::= { ciscoAtmSnoopVpEntry 5} -- global config of frame discard SVC usage ciscoAtmSvcFrameDiscardUsesAal5Ie OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Determines mechanism to use on interfaces to specify frame discard. Specifying a value of true causes the presence of the AAL5 IE to influence whether frame discard is used on an SVC. If AAL5 IE is present in a received SETUP, frame discard is used. Specifying a value of false results in no influence on presence of the frame discard by the AAL5 IE." DEFVAL { true } ::= { ciscoAtmSvc 2 } -- conformance information ciscoAtmConnMIBConformance OBJECT IDENTIFIER ::= { ciscoAtmConnMIB 3 } ciscoAtmConnMIBCompliances OBJECT IDENTIFIER ::= { ciscoAtmConnMIBConformance 1 } ciscoAtmConnMIBGroups OBJECT IDENTIFIER ::= { ciscoAtmConnMIBConformance 2 } -- compliance statements ciscoAtmConnMIBCompliance MODULE-COMPLIANCE STATUS obsolete -- susperseded by ciscoAtmConnMIBCompliances2 DESCRIPTION "The compliance statement for the Cisco ATM connection management group." MODULE -- this module MANDATORY-GROUPS { ciscoAtmConnMIBGroup } ::= { ciscoAtmConnMIBCompliances 1 } ciscoAtmConnMIBCompliance2 MODULE-COMPLIANCE STATUS obsolete -- susperseded by ciscoAtmConnMIBCompliances3 DESCRIPTION "The compliance statement for the Cisco ATM connection management group." MODULE -- this module MANDATORY-GROUPS { ciscoAtmConnMIBGroup, ciscoAtmConnMIBGroup2 } ::= { ciscoAtmConnMIBCompliances 2 } ciscoAtmConnMIBCompliance3 MODULE-COMPLIANCE STATUS obsolete -- susperseded by ciscoAtmConnMIBCompliances4 DESCRIPTION "The compliance statement for the Cisco ATM connection management group." MODULE -- this module MANDATORY-GROUPS { ciscoAtmConnMIBGroup, ciscoAtmConnMIBGroup3, ciscoAtmConnMIBlsPerVcqGroup, ciscoAtmConnMIBlsFcPfqGroup } ::= { ciscoAtmConnMIBCompliances 3 } ciscoAtmConnMIBCompliance4 MODULE-COMPLIANCE STATUS obsolete -- susperseded by ciscoAtmConnMIBCompliances5 DESCRIPTION "The compliance statement for the Cisco ATM connection management group." MODULE -- this module MANDATORY-GROUPS { ciscoAtmConnMIBGroup, ciscoAtmConnMIBGroup3, ciscoAtmConnMIBlsPerVcqGroup2, ciscoAtmConnMIBlsFcPfqGroup } ::= { ciscoAtmConnMIBCompliances 4 } ciscoAtmConnMIBCompliance5 MODULE-COMPLIANCE STATUS deprecated -- superseded by ciscoAtmConnMIBCompliances6 DESCRIPTION "The compliance statement for the Cisco ATM connection management group." MODULE -- this module MANDATORY-GROUPS { ciscoAtmConnMIBGroup, ciscoAtmConnMIBGroup3, ciscoAtmConnMIBlsPerVcqGroup2, ciscoAtmConnMIBlsFcPfqGroup, ciscoAtmConnMIBNegTraffGroup } ::= { ciscoAtmConnMIBCompliances 5 } ciscoAtmConnMIBCompliance6 MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "The compliance statement for the Cisco ATM connection management group." MODULE -- this module MANDATORY-GROUPS { ciscoAtmConnMIBGroup, ciscoAtmConnMIBGroup3, ciscoAtmConnMIBlsPerVcqGroup2, ciscoAtmConnMIBlsFcPfqGroup1, ciscoAtmConnMIBNegTraffGroup } ::= { ciscoAtmConnMIBCompliances 6 } ciscoAtmConnMIBCompliance7 MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "The compliance statement for the Cisco ATM connection management group." MODULE -- this module MANDATORY-GROUPS { ciscoAtmConnMIBGroup1, ciscoAtmConnMIBGroup3, ciscoAtmConnMIBlsPerVcqGroup2, ciscoAtmConnMIBlsFcPfqGroup1, ciscoAtmConnMIBNegTraffGroup } ::= { ciscoAtmConnMIBCompliances 7 } ciscoAtmConnMIBCompliance8 MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for the Cisco ATM connection management group." MODULE -- this module MANDATORY-GROUPS { ciscoAtmConnMIBGroup4, ciscoAtmConnMIBGroup3, ciscoAtmConnMIBlsPerVcqGroup2, ciscoAtmConnMIBlsFcPfqGroup1, ciscoAtmConnMIBNegTraffGroup } GROUP ciscoAtmConnNmsGroup DESCRIPTION "This is an optional group" ::= { ciscoAtmConnMIBCompliances 8 } -- units of conformance ciscoAtmConnMIBGroup OBJECT-GROUP OBJECTS { ciscoAtmVplCastType, ciscoAtmVplSpanType, ciscoAtmVplConfigType, ciscoAtmVplRxUpcMode, ciscoAtmVplConnState, ciscoAtmVplOamLoopbkTxInterval, ciscoAtmVplOamSegmentLoopback, ciscoAtmVplOamEndLoopback, ciscoAtmVplOamAisEnable, ciscoAtmVplOamRdiEnable, ciscoAtmVplInstallTime, ciscoAtmVplInCells, ciscoAtmVplOutCells, ciscoAtmVplCrossIfIndex, ciscoAtmVplCrossVpi, ciscoAtmVplNextLeafIfIndex, ciscoAtmVplNextLeafVpi, ciscoAtmVplRemoteAddr, ciscoAtmVplRemoteVpi, ciscoAtmVplLocation, ciscoAtmVplSlowRetryIntv, ciscoAtmVplNumAttempts, ciscoAtmVplLastReleaseCause, ciscoAtmVplLogicalPortDef, ciscoAtmVplLogicalPortIndex, ciscoAtmVclCastType, ciscoAtmVclSpanType, ciscoAtmVclConfigType, ciscoAtmVclRxUpcMode, ciscoAtmVclEpdEnable, ciscoAtmVclConnState, ciscoAtmVclOamLoopbkTxInterval, ciscoAtmVclOamSegmentLoopback, ciscoAtmVclOamEndLoopback, ciscoAtmVclOamAisEnable, ciscoAtmVclOamRdiEnable, ciscoAtmVclInstallTime, ciscoAtmVclInCells, ciscoAtmVclOutCells, ciscoAtmVclCrossIfIndex, ciscoAtmVclCrossVpi, ciscoAtmVclCrossVci, ciscoAtmVclNextLeafIfIndex, ciscoAtmVclNextLeafVpi, ciscoAtmVclNextLeafVci, ciscoAtmVclAalEncapFlag, ciscoAtmVclAalEncapProtocol, ciscoAtmVclAalUserVcType, ciscoAtmVclAtmInArpInterval, ciscoAtmVclRemoteAddr, ciscoAtmVclRemoteVpi, ciscoAtmVclRemoteVci, ciscoAtmVclLocation, ciscoAtmVclSlowRetryIntv, ciscoAtmVclNumAttempts, ciscoAtmVclLastReleaseCause, ciscoAtmSvpDirection, ciscoAtmSvcDirection } STATUS deprecated DESCRIPTION "" ::= { ciscoAtmConnMIBGroups 1 } ciscoAtmConnMIBGroup2 OBJECT-GROUP OBJECTS { ciscoAtmVplUpcViolations, ciscoAtmVplEpdTpdCellDrops, ciscoAtmVplEpdTpdPacketDrops, ciscoAtmVplEpdTpdPacketsIn, ciscoAtmVplClp1Drops, ciscoAtmVplDefaultRxUpcTolerance, ciscoAtmVclUpcViolations, ciscoAtmVclEpdTpdCellDrops, ciscoAtmVclEpdTpdPacketDrops, ciscoAtmVclEpdTpdPacketsIn, ciscoAtmVclClp1Drops, ciscoAtmVclDefaultRxUpcTolerance, ciscoAtmSvcFrameDiscardUsesAal5Ie } STATUS obsolete DESCRIPTION "" ::= { ciscoAtmConnMIBGroups 2 } ciscoAtmConnMIBGroup3 OBJECT-GROUP OBJECTS { ciscoAtmVplDefaultRxUpcTolerance, ciscoAtmVclDefaultRxUpcTolerance, ciscoAtmVplDefaultRxUpcVbrCdvt, ciscoAtmVclDefaultRxUpcVbrCdvt, ciscoAtmSvcFrameDiscardUsesAal5Ie } STATUS current DESCRIPTION "" ::= { ciscoAtmConnMIBGroups 3 } ciscoAtmConnMIBlsPerVcqGroup OBJECT-GROUP OBJECTS { ciscoAtmVplLsPerVcqWrrWeight, ciscoAtmVplLsPerVcqTunnelIsShaped, ciscoAtmVplLsPerVcqXmtQueuedCells, ciscoAtmVplLsPerVcQThreshGrp, ciscoAtmVclLsPerVcqWrrWeight, ciscoAtmVclLsPerVcqXmtQueuedCells, ciscoAtmVclLsPerVcQThreshGrp, ciscoAtmSnoopVcSnoopedIfIndex, ciscoAtmSnoopVcSnoopedVpi, ciscoAtmSnoopVcSnoopedVci, ciscoAtmSnoopVcDir, ciscoAtmSnoopVcState, ciscoAtmSnoopVcRowStatus, ciscoAtmSnoopVpSnoopedIfIndex, ciscoAtmSnoopVpSnoopedVpi, ciscoAtmSnoopVpDir, ciscoAtmSnoopVpState, ciscoAtmSnoopVpRowStatus } STATUS obsolete DESCRIPTION "A collection of objects which are supported on platforms using the Lightstream per-VC queueing chipset." ::= { ciscoAtmConnMIBGroups 4 } ciscoAtmConnMIBlsFcPfqGroup OBJECT-GROUP OBJECTS { ciscoAtmVplUpcViolations, ciscoAtmVclUpcViolations, ciscoAtmVclEpdTpdPacketDrops, ciscoAtmVclEpdTpdPacketsIn, ciscoAtmVplInClp0Cells, ciscoAtmVplInClp1Cells, ciscoAtmVplOutClp0Cells, ciscoAtmVplOutClp1Cells, ciscoAtmVplCellDrops, ciscoAtmVplClp0VcqFullCellDrops, ciscoAtmVplVcqClpThreshCellDrops, ciscoAtmVclInClp0Cells, ciscoAtmVclInClp1Cells, ciscoAtmVclOutClp0Cells, ciscoAtmVclOutClp1Cells, ciscoAtmVclCellDrops, ciscoAtmVclClp0VcqFullCellDrops, ciscoAtmVclVcqClpThreshCellDrops } STATUS deprecated -- susperseded by ciscoAtmConnMIBlsFcPfqGroup1 DESCRIPTION "A collection of objects which are supported on LS1010 systems equipped with the FC-PFQ feature card." ::= { ciscoAtmConnMIBGroups 5 } ciscoAtmConnMIBlsPerVcqGroup2 OBJECT-GROUP OBJECTS { ciscoAtmVplLsPerVcqWrrWeight, ciscoAtmVplLsPerVcqTunnelIsShaped, ciscoAtmVplLsPerVcqTunnelIsHierarchical, ciscoAtmVplLsPerVcqXmtQueuedCells, ciscoAtmVplLsPerVcQThreshGrp, ciscoAtmVclLsPerVcqWrrWeight, ciscoAtmVclLsPerVcqXmtQueuedCells, ciscoAtmVclLsPerVcQThreshGrp, ciscoAtmSnoopVcSnoopedIfIndex, ciscoAtmSnoopVcSnoopedVpi, ciscoAtmSnoopVcSnoopedVci, ciscoAtmSnoopVcDir, ciscoAtmSnoopVcState, ciscoAtmSnoopVcRowStatus, ciscoAtmSnoopVpSnoopedIfIndex, ciscoAtmSnoopVpSnoopedVpi, ciscoAtmSnoopVpDir, ciscoAtmSnoopVpState, ciscoAtmSnoopVpRowStatus } STATUS current DESCRIPTION "A collection of objects which are supported on platforms using the Lightstream per-VC queueing chipset." ::= { ciscoAtmConnMIBGroups 6 } ciscoAtmConnMIBNegTraffGroup OBJECT-GROUP OBJECTS { ciscoAtmVplRxNegTraffDescrIndex, ciscoAtmVplTxNegTraffDescrIndex, ciscoAtmVclRxNegTraffDescrIndex, ciscoAtmVclTxNegTraffDescrIndex } STATUS current DESCRIPTION "A collection of objects to report negotiated traffic parameters on a Cisco ATM switch." ::= { ciscoAtmConnMIBGroups 7 } ciscoAtmConnMIBlsFcPfqGroup1 OBJECT-GROUP OBJECTS { ciscoAtmVplUpcViolations, ciscoAtmVclUpcViolations, ciscoAtmVclEpdTpdPacketDrops, ciscoAtmVclEpdTpdPacketsIn, ciscoAtmVplInClp0Cells, ciscoAtmVplInClp1Cells, ciscoAtmVplOutClp0Cells, ciscoAtmVplOutClp1Cells, ciscoAtmVplCellDrops, ciscoAtmVplClp0VcqFullCellDrops, ciscoAtmVplVcqClpThreshCellDrops, ciscoAtmVplSwFabOutCells, ciscoAtmVplSwFabOutClp0Cells, ciscoAtmVplSwFabOutClp1Cells, ciscoAtmVclInClp0Cells, ciscoAtmVclInClp1Cells, ciscoAtmVclOutClp0Cells, ciscoAtmVclOutClp1Cells, ciscoAtmVclCellDrops, ciscoAtmVclClp0VcqFullCellDrops, ciscoAtmVclVcqClpThreshCellDrops, ciscoAtmVclSwFabOutCells, ciscoAtmVclSwFabOutClp0Cells, ciscoAtmVclSwFabOutClp1Cells } STATUS current DESCRIPTION "A collection of objects which are supported on LS1010 systems equipped with the FC-PFQ feature card." ::= { ciscoAtmConnMIBGroups 8 } ciscoAtmConnMIBGroup1 OBJECT-GROUP OBJECTS { ciscoAtmVplCastType, ciscoAtmVplSpanType, ciscoAtmVplConfigType, ciscoAtmVplRxUpcMode, ciscoAtmVplConnState, ciscoAtmVplOamLoopbkTxInterval, ciscoAtmVplOamSegmentLoopback, ciscoAtmVplOamEndLoopback, ciscoAtmVplOamAisEnable, ciscoAtmVplOamRdiEnable, ciscoAtmVplInstallTime, ciscoAtmVplInCells, ciscoAtmVplOutCells, ciscoAtmVplCrossIfIndex, ciscoAtmVplCrossVpi, ciscoAtmVplNextLeafIfIndex, ciscoAtmVplNextLeafVpi, ciscoAtmVplRemoteAddr, ciscoAtmVplRemoteVpi, ciscoAtmVplLocation, ciscoAtmVplSlowRetryIntv, ciscoAtmVplNumAttempts, ciscoAtmVplLastReleaseCause, ciscoAtmVplLogicalPortDef, ciscoAtmVplLogicalPortIndex, ciscoAtmVplConnName, ciscoAtmVclCastType, ciscoAtmVclSpanType, ciscoAtmVclConfigType, ciscoAtmVclRxUpcMode, ciscoAtmVclEpdEnable, ciscoAtmVclConnState, ciscoAtmVclOamLoopbkTxInterval, ciscoAtmVclOamSegmentLoopback, ciscoAtmVclOamEndLoopback, ciscoAtmVclOamAisEnable, ciscoAtmVclOamRdiEnable, ciscoAtmVclInstallTime, ciscoAtmVclInCells, ciscoAtmVclOutCells, ciscoAtmVclCrossIfIndex, ciscoAtmVclCrossVpi, ciscoAtmVclCrossVci, ciscoAtmVclNextLeafIfIndex, ciscoAtmVclNextLeafVpi, ciscoAtmVclNextLeafVci, ciscoAtmVclAalEncapFlag, ciscoAtmVclAalEncapProtocol, ciscoAtmVclAalUserVcType, ciscoAtmVclAtmInArpInterval, ciscoAtmVclRemoteAddr, ciscoAtmVclRemoteVpi, ciscoAtmVclRemoteVci, ciscoAtmVclLocation, ciscoAtmVclSlowRetryIntv, ciscoAtmVclNumAttempts, ciscoAtmVclLastReleaseCause, ciscoAtmVclConnName, ciscoAtmSvpDirection, ciscoAtmSvcDirection } STATUS deprecated DESCRIPTION "" ::= { ciscoAtmConnMIBGroups 9 } ciscoAtmConnMIBGroup4 OBJECT-GROUP OBJECTS { ciscoAtmVplCastType, ciscoAtmVplSpanType, ciscoAtmVplConfigType, ciscoAtmVplRxUpcMode, ciscoAtmVplConnState, ciscoAtmVplOamLoopbkTxInterval, ciscoAtmVplOamSegmentLoopback, ciscoAtmVplOamEndLoopback, ciscoAtmVplOamAisEnable, ciscoAtmVplOamRdiEnable, ciscoAtmVplInstallTime, ciscoAtmVplInCells, ciscoAtmVplOutCells, ciscoAtmVplCrossIfIndex, ciscoAtmVplCrossVpi, ciscoAtmVplNextLeafIfIndex, ciscoAtmVplNextLeafVpi, ciscoAtmVplRemoteAddr, ciscoAtmVplRemoteVpi, ciscoAtmVplLocation, ciscoAtmVplSlowRetryIntv, ciscoAtmVplNumAttempts, ciscoAtmVplLastReleaseCause, ciscoAtmVplLogicalPortDef, ciscoAtmVplLogicalPortIndex, ciscoAtmVclCastType, ciscoAtmVclSpanType, ciscoAtmVclConfigType, ciscoAtmVclRxUpcMode, ciscoAtmVclEpdEnable, ciscoAtmVclConnState, ciscoAtmVclOamLoopbkTxInterval, ciscoAtmVclOamSegmentLoopback, ciscoAtmVclOamEndLoopback, ciscoAtmVclOamAisEnable, ciscoAtmVclOamRdiEnable, ciscoAtmVclInstallTime, ciscoAtmVclInCells, ciscoAtmVclOutCells, ciscoAtmVclCrossIfIndex, ciscoAtmVclCrossVpi, ciscoAtmVclCrossVci, ciscoAtmVclNextLeafIfIndex, ciscoAtmVclNextLeafVpi, ciscoAtmVclNextLeafVci, ciscoAtmVclAalEncapFlag, ciscoAtmVclAalEncapProtocol, ciscoAtmVclAalUserVcType, ciscoAtmVclAtmInArpInterval, ciscoAtmVclRemoteAddr, ciscoAtmVclRemoteVpi, ciscoAtmVclRemoteVci, ciscoAtmVclLocation, ciscoAtmVclSlowRetryIntv, ciscoAtmVclNumAttempts, ciscoAtmVclLastReleaseCause, ciscoAtmSvpDirection, ciscoAtmSvcDirection } STATUS current DESCRIPTION "" ::= { ciscoAtmConnMIBGroups 10 } ciscoAtmConnNmsGroup OBJECT-GROUP OBJECTS { ciscoAtmVplConnName, ciscoAtmVplConnType, ciscoAtmVclConnName, ciscoAtmVclConnType } STATUS current DESCRIPTION "A group of objects that provides additional information for a management system" ::= { ciscoAtmConnMIBGroups 11 } END