-- *****************************************************************
-- BASIS-SERIAL-MIB: Serial Port MIB MGX8250 and MGX8220 products.
--
-- May 2003, Subra Hegde
--
-- Copyright (c) 2003 by cisco Systems, Inc.
-- All rights reserved.
-- ****************************************************************

BASIS-SERIAL-MIB DEFINITIONS ::= BEGIN
IMPORTS
    MODULE-IDENTITY,
    OBJECT-TYPE,
    Integer32                  FROM SNMPv2-SMI
    MODULE-COMPLIANCE,
    OBJECT-GROUP               FROM SNMPv2-CONF
    basisLines                 FROM BASIS-MIB
    ciscoWan                   FROM CISCOWAN-SMI;

basisSerialMIB MODULE-IDENTITY
    LAST-UPDATED    "200305030000Z"
    ORGANIZATION    "Cisco Systems, Inc."
    CONTACT-INFO
            "       Cisco Systems
                        Customer Service

                Postal: 170 W Tasman Drive
                        San Jose, CA  95134
                        USA

                        Tel: +1 800 553-NETS

                E-mail: cs-wanatm@cisco.com"
    DESCRIPTION
        "The MIB module to configure serial ports
        in Processor Module and different Service 
        Modules(cards) in MGX8850,MGX8250 and MGX8220
        ATM Edge switches."

     REVISION    "200305030000Z"
    DESCRIPTION
        "Initial version of the MIB.

        The content of this MIB was originally available
        in CISCO-WAN-AXIPOP-MIB defined using SMIv1.
        The applicable objects from CISCO-WAN-AXIPOP-MIB
        are defined using SMIv2 in this MIB. Also the
        descriptions of some of the objects have been 
        modified."
    ::= { ciscoWan 69 }


serialInterface         OBJECT IDENTIFIER ::= {basisLines 1}

-- ***************************************************************
--
-- serial interface table                                      
--
-- ***************************************************************

serialPortNumOfValidEntries   OBJECT-TYPE
    SYNTAX     Integer32(1..2)
    MAX-ACCESS read-only
    STATUS     current
    DESCRIPTION
        "This object contains number of serial ports.
        This identifies the number of entries in
        serialInterfacetable."
    ::= { serialInterface 2 }

serialInterfaceTable   OBJECT-TYPE
    SYNTAX  SEQUENCE OF SerialInterfaceEntry
    MAX-ACCESS  not-accessible
    STATUS  current
    DESCRIPTION
        "This table represents Physical serial interfaces in
        the module."
    ::= { serialInterface 1 }

serialInterfaceEntry   OBJECT-TYPE
    SYNTAX  SerialInterfaceEntry
    MAX-ACCESS  not-accessible
    STATUS  current
    DESCRIPTION
        "An entry for each serial interface. 
        Each entry contains information on
        port type, port speed."
    INDEX   { serialPortNum }
    ::= { serialInterfaceTable 1}
 
SerialInterfaceEntry ::=
    SEQUENCE {
        serialPortNum       Integer32,
        serialPortType      INTEGER,
        serialPortEnable    INTEGER,
        serialPortbps       INTEGER
    }

serialPortNum OBJECT-TYPE
    SYNTAX     Integer32(1..2)
    MAX-ACCESS read-only
    STATUS     current
    DESCRIPTION
         "This object identifies the serial port number.

         The value 1 is used for Console Port.
         The Console Port is also known as control port(CP).

         The value 2 is used for Maintenance Port
         and this can be used as SLIP
         (Serial Line Internet Protocol) interface.
         The Maintenance Port is also known as 
         Modem Port(MP)."
    ::= { serialInterfaceEntry 1 }

serialPortType OBJECT-TYPE
    SYNTAX  INTEGER {
                main  (1),
                debug (2)
    }
    MAX-ACCESS  read-only
    STATUS  current
    DESCRIPTION
        "This object identifies the type of port.
        
        main(1)  : This is applicable for Maintenance Port
        debug(2) : This is applicable for Console Port."
    ::= { serialInterfaceEntry 2 }

serialPortEnable OBJECT-TYPE
    SYNTAX  INTEGER {
                disable (1),
                enable  (2)
            }
    MAX-ACCESS  read-write
    STATUS  current
    DESCRIPTION
        "This object is used for enabling/disabling
        serial port."
    ::= { serialInterfaceEntry 3 }

serialPortbps OBJECT-TYPE
    SYNTAX  INTEGER {
                bps9600     (1),
                bps2400     (2),
                bps19200    (3)
    }
    MAX-ACCESS  read-write
    STATUS  current
    DESCRIPTION
        "This object identifies the baud rate of the ports."
    DEFVAL { bps9600 }
    ::= { serialInterfaceEntry 4 }


-- conformance information

basisSerialMIBConformance  OBJECT IDENTIFIER ::= { basisSerialMIB 2 }

basisSerialMIBGroups       OBJECT IDENTIFIER ::= 
                              { basisSerialMIBConformance 1 }

basisSerialMIBCompliances  OBJECT IDENTIFIER ::= 
                              { basisSerialMIBConformance 2 }

-- compliance statements

basisSerialCompliance MODULE-COMPLIANCE
    STATUS  current
    DESCRIPTION
        "The compliance statement for objects related
        to Serial Ports."
    MODULE  -- this module
        MANDATORY-GROUPS {
            basisSerialConfGroup
        }
    ::= { basisSerialMIBCompliances 1 }

basisSerialConfGroup OBJECT-GROUP
    OBJECTS {
        serialPortNumOfValidEntries,
        serialPortNum,
        serialPortType,
        serialPortEnable,
        serialPortbps
      }
      STATUS current
      DESCRIPTION
          "The collection of objects which are used to represent
          serial ports."
      ::= { basisSerialMIBGroups 1 }

END