-- 3Com Switching Systems QOS Management Information Base -- Version 1.0.0 -- February 13, 1998 -- 3Com Corporation -- 80 Central Street -- Boxborough, MA 01719 -- (508) 264-1400 ---------------------------------------------------------------------------------------- -- 08/03/99 - lam Added support for SNMP trap feature to QoS One-Way TCP Filter -- functionality. -- 01/24/98 - tmeiczin Added qos non flow classifiers for Custom types -- 08/14/98 - tmeiczin Fixed syntax to compiled with SMICng -- 02/13/98 - iwolf Originally created -- ---------------------------------------------------------------------------------------- A3COM-SWITCHING-SYSTEMS-QOS-MIB DEFINITIONS ::= BEGIN IMPORTS enterprises, Gauge, IpAddress FROM RFC1155-SMI DisplayString, ifIndex FROM RFC1213-MIB OBJECT-TYPE FROM RFC-1212 TRAP-TYPE FROM RFC-1215; -- RowStatus -- FROM SNMPv2-TC; -- The Following was removed to allow compiling with SunNet Manager -- RowStatus -- FROM SNMPv2-TC; RowStatus ::= INTEGER { -- the following two values are states: -- these values may be read or written active(1), notInService(2), -- the following value is a state: -- this value may be read, but not written notReady(3), -- the following three values are -- actions: these values may be written, -- but are never read createAndGo(4), createAndWait(5), destroy(6) } -- Object identifiers a3Com OBJECT IDENTIFIER ::= { enterprises 43 } switchingSystemsMibs OBJECT IDENTIFIER ::= { a3Com 29 } a3ComSwitchingSystemsMib OBJECT IDENTIFIER ::= { switchingSystemsMibs 4 } a3ComQos OBJECT IDENTIFIER ::= { a3ComSwitchingSystemsMib 21 } -- Qos groups a3ComQosClass OBJECT IDENTIFIER ::= { a3ComQos 1 } a3ComQosCtrl OBJECT IDENTIFIER ::= { a3ComQos 2 } a3ComQosRsvp OBJECT IDENTIFIER ::= { a3ComQos 3 } a3ComQosStats OBJECT IDENTIFIER ::= { a3ComQos 4 } a3ComQosMisc OBJECT IDENTIFIER ::= { a3ComQos 5 } -- -- The QoS Generic Class Table. -- a3ComQosGenClassTable OBJECT-TYPE SYNTAX SEQUENCE OF A3ComQosGenClassEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This table lists all QoS classes (Flow and Non-Flow) configured in the system." ::= { a3ComQosClass 1 } a3ComQosGenClassEntry OBJECT-TYPE SYNTAX A3ComQosGenClassEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry describing a single class entity." INDEX { a3ComQosGenClassIndex } ::= { a3ComQosGenClassTable 1 } A3ComQosGenClassEntry ::= SEQUENCE { a3ComQosGenClassIndex INTEGER, a3ComQosGenClassName DisplayString, a3ComQosGenClassControlId INTEGER } a3ComQosGenClassIndex OBJECT-TYPE SYNTAX INTEGER (1..65532) ACCESS read-only STATUS mandatory DESCRIPTION "A unique value for each entry." ::= { a3ComQosGenClassEntry 1 } a3ComQosGenClassName OBJECT-TYPE SYNTAX DisplayString (SIZE(0..32)) ACCESS read-write STATUS mandatory DESCRIPTION "A textual name for the class." ::= { a3ComQosGenClassEntry 2 } a3ComQosGenClassControlId OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "The control entry that this class is associated with. Note that the user must have created the control (via the a3ComQosCtrlTable) before making the association via this object. A value of zero indicates no control is attached." ::= { a3ComQosGenClassEntry 3 } -- -- The QoS Flow Class Table. -- a3ComQosFlowClassTable OBJECT-TYPE SYNTAX SEQUENCE OF A3ComQosFlowClassEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This table lists the Flow classes defined in the system. A Flow class applies only to IP unicast and multicast packets. A Flow class is defined in terms of the IP packet header: IP protocol type, IP source and destination addresses, TCP/UDP source and destination ports. Note that a filter entry can only be modified if there is no control attached to it. Otherwise, the entry has to be deleted and recreated." ::= { a3ComQosClass 2 } a3ComQosFlowClassEntry OBJECT-TYPE SYNTAX A3ComQosFlowClassEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry describing a single flow class entity." INDEX { a3ComQosFlowClassIndex, a3ComQosFlowClassFilterIndex } ::= { a3ComQosFlowClassTable 1 } A3ComQosFlowClassEntry ::= SEQUENCE { a3ComQosFlowClassIndex INTEGER, a3ComQosFlowClassFilterIndex INTEGER, a3ComQosFlowClassCastType INTEGER, a3ComQosFlowClassIpProtoType INTEGER, a3ComQosFlowClassSrcAddr IpAddress, a3ComQosFlowClassSrcSubnetMask IpAddress, a3ComQosFlowClassDestAddr IpAddress, a3ComQosFlowClassDestSubnetMask IpAddress, a3ComQosFlowClassPortStart INTEGER, a3ComQosFlowClassPortEnd INTEGER, a3ComQosFlowClassRowStatus RowStatus } a3ComQosFlowClassIndex OBJECT-TYPE SYNTAX INTEGER (1..65532) ACCESS read-only STATUS mandatory DESCRIPTION "A unique value for each entry. Flow classses use id values between 1-399." ::= { a3ComQosFlowClassEntry 1 } a3ComQosFlowClassFilterIndex OBJECT-TYPE SYNTAX INTEGER (1..100) ACCESS read-only STATUS mandatory DESCRIPTION "The unique filter index associated with this class. Note that the maximum limit of 100 filters is the aggregate of all the filters defined in the system, not just the number of filters defined for this classifier." ::= { a3ComQosFlowClassEntry 2 } a3ComQosFlowClassCastType OBJECT-TYPE SYNTAX INTEGER { unicast(1), multicast(2), both(3) } ACCESS read-write STATUS mandatory DESCRIPTION "The network layer cast type for this class." DEFVAL { both } ::= { a3ComQosFlowClassEntry 3 } a3ComQosFlowClassIpProtoType OBJECT-TYPE SYNTAX INTEGER { udp(1), tcp(2), both(3) } ACCESS read-write STATUS mandatory DESCRIPTION "The IP protocol type for this class." DEFVAL { both } ::= { a3ComQosFlowClassEntry 4 } a3ComQosFlowClassSrcAddr OBJECT-TYPE SYNTAX IpAddress ACCESS read-write STATUS mandatory DESCRIPTION "The source IP address for this class." ::= { a3ComQosFlowClassEntry 5 } a3ComQosFlowClassSrcSubnetMask OBJECT-TYPE SYNTAX IpAddress ACCESS read-write STATUS mandatory DESCRIPTION "The source subnet mask for this class." ::= { a3ComQosFlowClassEntry 6 } a3ComQosFlowClassDestAddr OBJECT-TYPE SYNTAX IpAddress ACCESS read-write STATUS mandatory DESCRIPTION "The destination IP address for this class." ::= { a3ComQosFlowClassEntry 7 } a3ComQosFlowClassDestSubnetMask OBJECT-TYPE SYNTAX IpAddress ACCESS read-write STATUS mandatory DESCRIPTION "The destination subnet mask for this class." ::= { a3ComQosFlowClassEntry 8 } a3ComQosFlowClassPortStart OBJECT-TYPE SYNTAX INTEGER (0..65535) ACCESS read-write STATUS mandatory DESCRIPTION "The starting range of ports associated with this class." DEFVAL { 0 } ::= { a3ComQosFlowClassEntry 9 } a3ComQosFlowClassPortEnd OBJECT-TYPE SYNTAX INTEGER (0..65535) ACCESS read-write STATUS mandatory DESCRIPTION "The finishing range of ports associated with this class." DEFVAL { 65535 } ::= { a3ComQosFlowClassEntry 10 } a3ComQosFlowClassRowStatus OBJECT-TYPE SYNTAX RowStatus ACCESS read-write STATUS mandatory DESCRIPTION "The status column for this entry. This object can be set to: createAndGo(4) destroy(6) The following value may be read: active(1) Setting this object to createAndGo(4) creates a row in in this table. The agent will allocate the next sequential filter index value for the newly created entry. Setting this object to destroy(6) will remove this entry. Note that only the entry with the highest a3ComQosFlowClassFilterIndex value can be deleted. Also, an entry can only be deleted if there is no control attached to it." ::= { a3ComQosFlowClassEntry 11 } -- -- The QoS Non-Flow Class Table. -- a3ComQosNonFlowClassTable OBJECT-TYPE SYNTAX SEQUENCE OF A3ComQosNonFlowClassEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This table lists the Non-Flow classes defined in the system. A Non-Flow class defines a packet in terms of its data link level protocol: IEEE 802.1p tag value, cast type (broadcast, multicast, and unicast). Packets which match a Non-Flow class receive a service level specific to that class." ::= { a3ComQosClass 3 } a3ComQosNonFlowClassEntry OBJECT-TYPE SYNTAX A3ComQosNonFlowClassEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry describing a single non-flow class entity." INDEX { a3ComQosNonFlowClassIndex } ::= { a3ComQosNonFlowClassTable 1 } A3ComQosNonFlowClassEntry ::= SEQUENCE { a3ComQosNonFlowClassIndex INTEGER, a3ComQosNonFlowClassCastType OCTET STRING, a3ComQosNonFlowClassProtos OCTET STRING, a3ComQosNonFlowClass8021pTags OCTET STRING, a3ComQosNonFlowClassRowStatus RowStatus, a3ComQosNonFlowClassProtoDescriptor INTEGER, a3ComQosNonFlowClassCustomProto OCTET STRING } a3ComQosNonFlowClassIndex OBJECT-TYPE SYNTAX INTEGER (1..65532) ACCESS read-only STATUS mandatory DESCRIPTION "A unique value for each entry. Non-flow classs use class ids values between 400-499." ::= { a3ComQosNonFlowClassEntry 1 } a3ComQosNonFlowClassCastType OBJECT-TYPE SYNTAX OCTET STRING (SIZE(1)) ACCESS read-write STATUS mandatory DESCRIPTION "A bit mask of 'cast' types associated with this class. Each cast is represented by a single bit. If that bit is set then the corresponding cast is selected by this class. The following bits are currently defined: Unicast 0x01 Multicast 0x02 Broadcast 0x04" DEFVAL { '07'H } ::= { a3ComQosNonFlowClassEntry 2 } a3ComQosNonFlowClassProtos OBJECT-TYPE SYNTAX OCTET STRING (SIZE(1)) ACCESS read-write STATUS mandatory DESCRIPTION "A bit mask of network protocols associated with this class. Each protocol is represented by a single bit. If that bit is set then the corresponding protocol is a member of this class. Only one protocol can be assigned to any given classifier. This object CAN ONLY BE SET if a3ComQosNonFlowClassProtoDesciptor is set to name(1) for the associated class. Custom (0x10) will be returned if a3ComQosNonFlowClassProtoDesciptor is not set to name(1). However this object CANNOT be set to Custom. The following bits are currently defined: Any 0x00 IP 0x01 IPX 0x02 TCP 0x04 Appletalk 0x08 Custom 0x10" DEFVAL { 'f'H } ::= { a3ComQosNonFlowClassEntry 3 } a3ComQosNonFlowClass8021pTags OBJECT-TYPE SYNTAX OCTET STRING(SIZE(1)) ACCESS read-write STATUS mandatory DESCRIPTION "A bit mask of the 802.1p tags associated with this class. Each tag is represented by a single bit. If that bit is set then the corresponding tag is selected by this class. The following bits are currently defined: 8021pTag-0 0x01 8021pTag-1 0x02 8021pTag-2 0x04 8021pTag-3 0x08 8021pTag-4 0x10 8021pTag-5 0x20 8021pTag-6 0x40 8021pTag-7 0x80" DEFVAL { 'ff'H } ::= { a3ComQosNonFlowClassEntry 4 } a3ComQosNonFlowClassRowStatus OBJECT-TYPE SYNTAX RowStatus ACCESS read-write STATUS mandatory DESCRIPTION "The status column for this entry. This object can be set to: createAndGo(4) destroy(6) The following value may be read: active(1) Setting this object to createAndGo(4) creates a row in in this table. Setting this object to destroy(6) will remove this entry. Note that an entry can only be deleted if there is no control attached to it." ::= { a3ComQosNonFlowClassEntry 5 } a3ComQosNonFlowClassProtoDescriptor OBJECT-TYPE SYNTAX INTEGER { name(1), ethertype (2), dsap-ssap (3) } ACCESS read-write STATUS mandatory DESCRIPTION "This object determines whether a3ComQosNonFlowClassProtos or a3ComQosNonFlowClassCustomProto is used to define the protocol for a classifier. If set to name(1), the pre-defined types Any, IP, IPX, TCP, AppleTalk from a3ComQosNonFlowClassProtos will be used. If set to ethertype(2) or dsap-ssap(3) then the a3ComQosNonFlowClassProtos will be custom and the value used will be determined by a3ComQosNonFlowClassCustomProto." DEFVAL { name } ::= { a3ComQosNonFlowClassEntry 6 } a3ComQosNonFlowClassCustomProto OBJECT-TYPE SYNTAX OCTET STRING(SIZE(2)) ACCESS read-write STATUS mandatory DESCRIPTION "This object determines a 2-byte hex value for the Ethertype or DSAP/SSAP that will be used in conjunction with a3ComQosNonFlowClassProtoDescriptor. If a3ComQosNonFlowClassProtoDescriptor is set to name(1) then this object is not used and it CANNOT be set. If a3ComQosNonFlowClassProtoDescriptor is set to ethertype(2) then the value will be used as an ethertype mask. If a3ComQosNonFlowClassProtoDescriptor is set to dsap-ssap(3) then the most significant byte will be used for the DSAP value and the least significant will be used for the SSAP value. -- Example 1: a3ComQosNonFlowClassProto is set to ethertype (2) a3ComQosNonFlowClassCustomTypeMask is set to 0x1234 The value 0x1234 will be used in the ethertype field. -- Example 2: a3ComQosNonFlowClassCustomType is set to dsap-ssap (2) a3ComQosNonFlowClassCustomTypeMask is set to 0x1234 The value 0x12 would be used for the DSAP value. The value 0x34 would be used for the SSAP value." ::= { a3ComQosNonFlowClassEntry 7 } -- -- The QoS Control Table. -- a3ComQosCtrlTable OBJECT-TYPE SYNTAX SEQUENCE OF A3ComQosCtrlEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A list of controls defined on a given system." ::= { a3ComQosCtrl 1 } a3ComQosCtrlEntry OBJECT-TYPE SYNTAX A3ComQosCtrlEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry describing a single QoS control." INDEX { a3ComQosCtrlIndex } ::= { a3ComQosCtrlTable 1 } A3ComQosCtrlEntry ::= SEQUENCE { a3ComQosCtrlIndex INTEGER, a3ComQosCtrlName DisplayString, a3ComQosCtrlServiceLevel INTEGER, a3ComQosCtrlConformPktsLossEligible INTEGER, a3ComQosCtrlExcessPktsServiceLevel INTEGER, a3ComQosCtrlExcessPktsLossEligible INTEGER, a3ComQosCtrl8021pTag INTEGER, a3ComQosCtrlRateLimitType INTEGER, a3ComQosCtrlRowStatus RowStatus } a3ComQosCtrlIndex OBJECT-TYPE SYNTAX INTEGER (1..65532) ACCESS read-only STATUS mandatory DESCRIPTION "A unique value for this entry." ::= { a3ComQosCtrlEntry 1 } a3ComQosCtrlName OBJECT-TYPE SYNTAX DisplayString (SIZE(0..32)) ACCESS read-write STATUS mandatory DESCRIPTION "A textual name for the control." DEFVAL { '00'H } ::= { a3ComQosCtrlEntry 2 } a3ComQosCtrlServiceLevel OBJECT-TYPE SYNTAX INTEGER { highPriority(1), bestEffort(2), lowPriority(3), drop(4) } ACCESS read-write STATUS mandatory DESCRIPTION "The service level for all conforming packets." DEFVAL { bestEffort } ::= { a3ComQosCtrlEntry 3 } a3ComQosCtrlConformPktsLossEligible OBJECT-TYPE SYNTAX INTEGER { eligible(1), nonEligible(2) } ACCESS read-write STATUS mandatory DESCRIPTION "The variable indicates whether conforming packets are loss eligible." DEFVAL { eligible } ::= { a3ComQosCtrlEntry 4 } a3ComQosCtrlExcessPktsServiceLevel OBJECT-TYPE SYNTAX INTEGER { highPriority(1), bestEffort(2), lowPriority(3), drop(4) } ACCESS read-write STATUS mandatory DESCRIPTION "The service level of excess packets for this control." DEFVAL { bestEffort } ::= { a3ComQosCtrlEntry 5 } a3ComQosCtrlExcessPktsLossEligible OBJECT-TYPE SYNTAX INTEGER { eligible(1), nonEligible(2) } ACCESS read-write STATUS mandatory DESCRIPTION "The variable indicates whether excess packets are loss eligible." DEFVAL { eligible } ::= { a3ComQosCtrlEntry 6 } a3ComQosCtrl8021pTag OBJECT-TYPE SYNTAX INTEGER { none(1), ieee8021pTag0(2), ieee8021pTag1(3), ieee8021pTag2(4), ieee8021pTag3(5), ieee8021pTag4(6), ieee8021pTag5(7), ieee8021pTag6(8), ieee8021pTag7(9) } ACCESS read-write STATUS mandatory DESCRIPTION "This indicates the tag to use on forwarded frames." DEFVAL { none } ::= { a3ComQosCtrlEntry 7 } a3ComQosCtrlRateLimitType OBJECT-TYPE SYNTAX INTEGER { none(1), receivePort(2), aggregate(3) } ACCESS read-write STATUS mandatory DESCRIPTION "The rate limit type to use with this control. A value of none(1) indicates that no rate limit is set for this control. A value of receivePort(2) indicates that the configured rate limit is applied on a per-port basis. A value of aggregate(3) indicates that the configured rate limit is aggregated across the set of ports that are configured for the rate limit. For values other than none(1), the rate limit entries are created via the a3ComQosCtrlRateLimitTable." DEFVAL { none } ::= { a3ComQosCtrlEntry 8 } a3ComQosCtrlRowStatus OBJECT-TYPE SYNTAX RowStatus ACCESS read-write STATUS mandatory DESCRIPTION "The status column for this control entry. This object can be set to: createAndGo(4) destroy(6) The following value may be read: active(1) Setting this object to createAndGo(4) creates a row in this table. Setting this object to destroy(6) will remove this entry. Note that a control can only be deleted if it is not attached to a flow or a non-flow classifier. A side effect of deleting a control in this table is the deletion of the corresponding rate limit entries in the a3ComQosCtrlRateLimitTable." ::= { a3ComQosCtrlEntry 9 } -- -- The QoS Control Rate Limit Table. -- a3ComQosCtrlRateLimitTable OBJECT-TYPE SYNTAX SEQUENCE OF A3ComQosCtrlRateLimitEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A list of QoS control rate limits defined on a given system." ::= { a3ComQosCtrl 2 } a3ComQosCtrlRateLimitEntry OBJECT-TYPE SYNTAX A3ComQosCtrlRateLimitEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry describing a single QoS control rate limit." INDEX { a3ComQosCtrlRateLimitCtrlIndex, a3ComQosCtrlRateLimitIndex } ::= { a3ComQosCtrlRateLimitTable 1 } A3ComQosCtrlRateLimitEntry ::= SEQUENCE { a3ComQosCtrlRateLimitCtrlIndex INTEGER, a3ComQosCtrlRateLimitIndex INTEGER, a3ComQosCtrlRateLimitPercent INTEGER, a3ComQosCtrlRateLimitKbps INTEGER, a3ComQosCtrlRateLimitPorts OCTET STRING, a3ComQosCtrlRateLimitRowStatus RowStatus } a3ComQosCtrlRateLimitCtrlIndex OBJECT-TYPE SYNTAX INTEGER (1..65532) ACCESS read-only STATUS mandatory DESCRIPTION "The control index for which this entry is valid." ::= { a3ComQosCtrlRateLimitEntry 1 } a3ComQosCtrlRateLimitIndex OBJECT-TYPE SYNTAX INTEGER (1..24) ACCESS read-only STATUS mandatory DESCRIPTION "The rate limit for which this entry is valid." ::= { a3ComQosCtrlRateLimitEntry 2 } a3ComQosCtrlRateLimitPercent OBJECT-TYPE SYNTAX INTEGER (0..101) ACCESS read-write STATUS mandatory DESCRIPTION "The rate limit as a percentage of input port bandwidth. Packets received in excess of specified rate limit will receive the service defined by value of a3ComQosCtrlExcessPktsServiceLevel object. A value of 0 indicates no rate limit. A value of 101 indicates that this object is not being used and the value of the a3ComQosCtrlRateLimitKbps object will determine the rate limit (if any)." DEFVAL { 0 } ::= { a3ComQosCtrlRateLimitEntry 3 } a3ComQosCtrlRateLimitKbps OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "The rate limit in kilobits per second of input port bandwidth. Packets received in excess of specified rate limit will receive the service defined by value of a3ComQosCtrlExcessPktsServiceLevel object. Note that the requested rate may be rounded up to the next 1/16th chunk bandwidth. Note that the user can specify the rate limit either as a percentage (via the a3ComQosCtrlRateLimitPercent object) or as kilobits per second (via this object) but not both. If the value of the a3ComQosCtrlRateLimitPercent object is 101, then the setting of this object determines the rate limit. A value of -1 for this object indicates no rate limit. Any other value indicates the desired rate limit." DEFVAL { -1 } ::= { a3ComQosCtrlRateLimitEntry 4 } a3ComQosCtrlRateLimitPorts OBJECT-TYPE SYNTAX OCTET STRING (SIZE(1..4)) ACCESS read-write STATUS mandatory DESCRIPTION "A bit mask of interfaces that support the defined rate limit. Each interface is represented by a single bit. If that bit is set then the corresponding interface is a member of this control. The bits are assigned with the least significant bit of the first byte corresponding to ifIndex 1, the next bit corresponding to ifIndex 2 and so on. Note that each port can only be associated with a single rate limit per control. An error will be returned if the user tries to assign a port that already has a rate limit associated with it." DEFVAL { '00'H } ::= { a3ComQosCtrlRateLimitEntry 5 } a3ComQosCtrlRateLimitRowStatus OBJECT-TYPE SYNTAX RowStatus ACCESS read-write STATUS mandatory DESCRIPTION "The status column for this rate limit entry. This object can be set to: createAndGo(4) destroy(6) The following value may be read: active(1) Setting this object to createAndGo(4) creates a row in this table. Note that a request to create a new entry must use the next sequential available a3ComQosCtrlRateLimitIndex value. Setting this object to destroy(6) will remove this entry." ::= { a3ComQosCtrlRateLimitEntry 6 } -- -- The QoS RSVP Group. -- a3ComQosRsvpStatus OBJECT-TYPE SYNTAX INTEGER { rsvpEnabled(1), rsvpDisabled(2) } ACCESS read-write STATUS mandatory DESCRIPTION "The status of the RSVP protocol." ::= { a3ComQosRsvp 1 } a3ComQosRsvpMaxTotalResvdBandwidth OBJECT-TYPE SYNTAX INTEGER(0..200) ACCESS read-write STATUS mandatory DESCRIPTION "The maximum total reservable bandwidth of the output link." ::= { a3ComQosRsvp 2 } a3ComQosRsvpMaxPerResvBandwidth OBJECT-TYPE SYNTAX INTEGER(0..100) ACCESS read-write STATUS mandatory DESCRIPTION "The maximum per-reservation bandwidth of the output link." ::= { a3ComQosRsvp 3 } a3ComQosRsvpPolicy OBJECT-TYPE SYNTAX INTEGER { edge(1), always(2), never(3) } ACCESS read-write STATUS mandatory DESCRIPTION "The indication of a policing option that shows when excess packets are dropped." ::= { a3ComQosRsvp 4 } a3ComQosRsvpExcessTrafficPolicy OBJECT-TYPE SYNTAX INTEGER { bestEffort(1), lowPriority(2) } ACCESS read-write STATUS mandatory DESCRIPTION "The indication of service for excess packets." ::= { a3ComQosRsvp 5 } a3ComQosRsvpExcessPktsLossEligible OBJECT-TYPE SYNTAX INTEGER { true(1), false(2) } ACCESS read-write STATUS mandatory DESCRIPTION "This object indicates if excess packets are loss eligible." ::= { a3ComQosRsvp 6 } a3ComQosRsvpAuthentication OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } ACCESS read-write STATUS mandatory DESCRIPTION "This object indicates the status of RSVP authentication." ::= { a3ComQosRsvp 7 } a3ComQosRsvpMd5Key OBJECT-TYPE SYNTAX OCTET STRING (SIZE(0..10)) ACCESS read-write STATUS mandatory DESCRIPTION "The MD5 encryption key. This value is used if the a3ComQosRsvpAuthStatus object is set to enabled(1)." ::= { a3ComQosRsvp 8 } -- -- The QoS stats rate interval. -- a3ComQosStatsInterval OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "The time interval, in seconds, over which rate statistics are collected. A value of zero implies absolute (i.e. raw) statistics." DEFVAL { 1 } ::= { a3ComQosStats 1 } -- -- The QoS Transmit Stats Table. -- a3ComQosXmtStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF A3ComQosXmtStatsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This table contains QoS transmit rate statistics. The interval over which the rate is calculated is determined by the value of a3ComQosStatsInterval object." ::= { a3ComQosStats 2 } a3ComQosXmtStatsEntry OBJECT-TYPE SYNTAX A3ComQosXmtStatsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry containing transmit rate statistics." INDEX { ifIndex, a3ComQosXmtStatsQindex } ::= { a3ComQosXmtStatsTable 1 } A3ComQosXmtStatsEntry ::= SEQUENCE { a3ComQosXmtStatsQindex INTEGER, a3ComQosXmtStatsLowLossPkts Gauge, a3ComQosXmtStatsLowLossDelayedPkts Gauge, a3ComQosXmtStatsLowLossDiscardedPkts Gauge, a3ComQosXmtStatsHighLossPkts Gauge, a3ComQosXmtStatsHighLossDiscardedPkts Gauge } a3ComQosXmtStatsQindex OBJECT-TYPE SYNTAX INTEGER { reserved(1), highPriority(2), bestEffort(3), lowPriority(4) } ACCESS read-only STATUS mandatory DESCRIPTION "The type of transmit queue for which this entry is valid." ::= { a3ComQosXmtStatsEntry 1 } a3ComQosXmtStatsLowLossPkts OBJECT-TYPE SYNTAX Gauge ACCESS read-only STATUS mandatory DESCRIPTION "The rate of low loss packets. Low loss packets are packets that are not marked as loss eligible (a3ComQosCtrlConformPktLossEligible object) and are under the threshold. The rate is specified in packets per second." ::= { a3ComQosXmtStatsEntry 2 } a3ComQosXmtStatsLowLossDelayedPkts OBJECT-TYPE SYNTAX Gauge ACCESS read-only STATUS mandatory DESCRIPTION "The rate of low loss delayed packets. Low loss delayed packets are packets that are not marked as loss eligible (a3ComQosCtrlConformPktLossEligible object) and are over the threshold. The rate is specified in packets per second." ::= { a3ComQosXmtStatsEntry 3 } a3ComQosXmtStatsLowLossDiscardedPkts OBJECT-TYPE SYNTAX Gauge ACCESS read-only STATUS mandatory DESCRIPTION "The rate of low loss discarded packets. Low loss discarded packets are packets that are discarded due to the queue being full. The rate is specified in packets per second." ::= { a3ComQosXmtStatsEntry 4 } a3ComQosXmtStatsHighLossPkts OBJECT-TYPE SYNTAX Gauge ACCESS read-only STATUS mandatory DESCRIPTION "The rate of high loss packets. High loss packets are packets that are marked as loss eligible (a3ComQosCtrlConformPktLossEligible object) and are under the threshold. The rate is specified in packets per second." ::= { a3ComQosXmtStatsEntry 5 } a3ComQosXmtStatsHighLossDiscardedPkts OBJECT-TYPE SYNTAX Gauge ACCESS read-only STATUS mandatory DESCRIPTION "The rate of high loss discarded packets. High loss discarded packets are packets that are marked as loss eligible (a3ComQosCtrlConformPktLossEligible object) and are over the threshold. The rate is specified in packets per second." ::= { a3ComQosXmtStatsEntry 6 } -- -- The QoS Transmit High Water Mark Statistics Table. -- a3ComQosXmtHmStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF A3ComQosXmtHmStatsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This table contains QoS transmit high water mark rate statistics. The interval over which the rate is calculated is determined by the value of a3ComQosStatsInterval object." ::= { a3ComQosStats 3 } a3ComQosXmtHmStatsEntry OBJECT-TYPE SYNTAX A3ComQosXmtHmStatsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry containing transmit high water mark rate statistics." INDEX { ifIndex, a3ComQosXmtHmStatsQindex } ::= { a3ComQosXmtHmStatsTable 1 } A3ComQosXmtHmStatsEntry ::= SEQUENCE { a3ComQosXmtHmStatsQindex INTEGER, a3ComQosXmtHmStatsLowLossPkts Gauge, a3ComQosXmtHmStatsLowLossDelayedPkts Gauge, a3ComQosXmtHmStatsLowLossDiscardedPkts Gauge, a3ComQosXmtHmStatsHighLossPkts Gauge, a3ComQosXmtHmStatsHighLossDiscardedPkts Gauge } a3ComQosXmtHmStatsQindex OBJECT-TYPE SYNTAX INTEGER { reserved(1), highPriority(2), bestEffort(3), lowPriority(4) } ACCESS read-only STATUS mandatory DESCRIPTION "The type of queue for which this entry is valid." ::= { a3ComQosXmtHmStatsEntry 1 } a3ComQosXmtHmStatsLowLossPkts OBJECT-TYPE SYNTAX Gauge ACCESS read-only STATUS mandatory DESCRIPTION "The high mark for low loss packets." ::= { a3ComQosXmtHmStatsEntry 2 } a3ComQosXmtHmStatsLowLossDelayedPkts OBJECT-TYPE SYNTAX Gauge ACCESS read-only STATUS mandatory DESCRIPTION "The high mark for low loss delayed packets." ::= { a3ComQosXmtHmStatsEntry 3 } a3ComQosXmtHmStatsLowLossDiscardedPkts OBJECT-TYPE SYNTAX Gauge ACCESS read-only STATUS mandatory DESCRIPTION "The high mark for low loss discarded packets." ::= { a3ComQosXmtHmStatsEntry 4 } a3ComQosXmtHmStatsHighLossPkts OBJECT-TYPE SYNTAX Gauge ACCESS read-only STATUS mandatory DESCRIPTION "The high mark for high loss packets." ::= { a3ComQosXmtHmStatsEntry 5 } a3ComQosXmtHmStatsHighLossDiscardedPkts OBJECT-TYPE SYNTAX Gauge ACCESS read-only STATUS mandatory DESCRIPTION "The high mark for high loss discarded packets." ::= { a3ComQosXmtHmStatsEntry 6 } -- -- The QoS Receive Statistics Table. -- a3ComQosRcvStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF A3ComQosRcvStatsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A table containing QoS receive rate statistics. The interval over which the rate is calculated is determined by the value of a3ComQosStatsInterval object." ::= { a3ComQosStats 4 } a3ComQosRcvStatsEntry OBJECT-TYPE SYNTAX A3ComQosRcvStatsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry containing receive rate statistics for a particular port." INDEX { ifIndex } ::= { a3ComQosRcvStatsTable 1 } A3ComQosRcvStatsEntry ::= SEQUENCE { a3ComQosRcvStatsConformBytesTotal Gauge, a3ComQosRcvStatsNonConformBytesForFlows Gauge, a3ComQosRcvStatsNonConformBytesForNonFlows Gauge, a3ComQosRcvStatsDroppedPkts Gauge } a3ComQosRcvStatsConformBytesTotal OBJECT-TYPE SYNTAX Gauge ACCESS read-only STATUS mandatory DESCRIPTION "The total conforming bytes receive rate. The rate is in bytes per second." ::= { a3ComQosRcvStatsEntry 1 } a3ComQosRcvStatsNonConformBytesForFlows OBJECT-TYPE SYNTAX Gauge ACCESS read-only STATUS mandatory DESCRIPTION "The non-conforming bytes receive rate for flows. The rate is in bytes per second." ::= { a3ComQosRcvStatsEntry 2 } a3ComQosRcvStatsNonConformBytesForNonFlows OBJECT-TYPE SYNTAX Gauge ACCESS read-only STATUS mandatory DESCRIPTION "The non-conforming bytes receive rate for non-flows. The rate is in bytes per second." ::= { a3ComQosRcvStatsEntry 3 } a3ComQosRcvStatsDroppedPkts OBJECT-TYPE SYNTAX Gauge ACCESS read-only STATUS mandatory DESCRIPTION "The number of packets dropped. The rate is specified in packets per second." ::= { a3ComQosRcvStatsEntry 4 } -- -- QoS Misc. Group. -- a3ComQosBandwidthRatio OBJECT-TYPE SYNTAX INTEGER (0..100) ACCESS read-write STATUS mandatory DESCRIPTION "The bandwidth ratio of HighPriority/(HighPriority+BestEffort) that is allocated for each output port on a given system. The value is represented as a percentage." ::= { a3ComQosMisc 1 } a3ComQosExcessTrafficClassTag OBJECT-TYPE SYNTAX INTEGER { none(1), ieee8021pTag0(2), ieee8021pTag1(3), ieee8021pTag2(4), ieee8021pTag3(5), ieee8021pTag4(6), ieee8021pTag5(7), ieee8021pTag6(8), ieee8021pTag7(9) } ACCESS read-write STATUS mandatory DESCRIPTION "This object indicates the IEEE802.1p traffic class value to use to retag excess packets." ::= { a3ComQosMisc 2 } a3ComQosFlowClassIntrudingEvent TRAP-TYPE ENTERPRISE a3ComSwitchingSystemsMib VARIABLES { a3ComQosFlowClassIndex, a3ComQosFlowClassIpProtoType, a3ComQosFlowClassSrcAddr, a3ComQosFlowClassDestAddr } DESCRIPTION "The trap that is generated when a intruder tries to enter a classified network" ::= 88 END