ctron-sfps-mcast-mib

ctron-sfps-mcast-mib Download

MIBs list

You can select a variable to monitor using the built-in IPHost MIB browser that provides you with all variables, their current values and descriptions taken from the ctron-sfps-mcast-mib .

OID list for ctron-sfps-mcast-mib

sfpsMcastCnxDestination
The multicast destination MAC address.
sfpsMcastCnxSource
The source MAC address.
sfpsMcastCnxSenderSw
The MAC address of the switch that the sender is on.
sfpsMcastCnxInPort
Local upstream port for flow.
sfpsMcastCnxOutPorts
Local downstream port(s) for flow.
sfpsMcastCnxGroup
Net layer ID of multicast group
sfpsMcastCnxTTL
Scope vlaue for this flow
sfpsMcastCnxAge
Age of local connection
sfpsMcastCnxStatus
Local connection status (bitwise)
sfpsMcastCnxNextSw
The MAC address of the next switch.
sfpsMcastCnxAPIDestination
Multicast destination MAC
sfpsMcastCnxAPISource
Multicast sender MAC
sfpsMcastCnxAPISenderSw
Mac of switch where sender is
sfpsMcastCnxAPIInPort
Local upstream port for flow
sfpsMcastCnxAPIOutPort
Local downstream port(s) for flow
sfpsMcastCnxAPIGroup
Net layer ID of multicast group
sfpsMcastCnxAPITTL
Scope value for this flow
sfpsMcastCnxAPIVerb
Action to take
sfpsMcastCnxAPIFilters
Count of local multicast filters
sfpsMcastCnxAPINonFilters
Count of local multicast connections
sfpsMcastIPRouterTable
sfpsMcastIPRouterEntry
sfpsMcastIPRouterIfNum
Port where multicast router is attached
sfpsMcastIPRouterVlanId
sfpsMcastIPRouterRouterIP
IP address of attached multicast router
sfpsMcastIPRouterTTL
Scope vlaue for this router
sfpsMcastIPRouterAPIVerb
Action to take
sfpsMcastIPRouterAPIIFNum
Port where multicast router is attached
sfpsMcastIPRouterAPIRouterIP
IP address of attached multicast router
sfpsMcastIPRouterAPITTLScope
Scope value for this router
sfpsMcastIPRouterAPIVlanId
sfpsMcastIPRIBTable
sfpsMcastIPRIBEntry
sfpsMcastIPRIBGroup
sfpsMcastIPRIBOrigin
Origin
sfpsMcastIPRIBInclusion
sfpsMcastIPRIBRcvPorts
Mask Object string
sfpsMcastIPRIBAge
CF time ticks
sfpsMcastIPRIBApiGroup
CF IP address IP multicast group address
sfpsMcastIPRIBApiPort
Port number, -1 means all ports
sfpsMcastIPRIBApiVerb
Action to take
sfpsMcastConfigApiSenderTableSize
This is the number of entries that are allocated in the multicast connection table at startup. Changing the value will not take effect until blade is reset. Values can be set between 0 and 2048.
sfpsMcastConfigApiMaxNonFilters
This number is currently not used. Its future purpose may be to control the number of multi-outport connections in use. Values can be set between 0 and 2048.
sfpsMcastConfigApiRDRetryBuffs
This number determines the number of packet objects that will be allocated by the reliable control packet transport agent. The packet object does not allocate space for the packet, it just manages the packet delivery machine. Each increment of this oid a ...
sfpsMcastConfigApiRDPktBuffs
This number determines the number of packet buffers that will be allocated by the reliable control packet transport agent. Each increment of this oid allocates space for 128 packets which are 512 bytes in size. Therefore each increment allocates about 65 ...
sfpsMcastConfigApiPendingMaps
This is the number of delayed connection mappings that will be maintained while waiting for topology changes to be propagated or while waiting for interswitch resolve. The effect of this setting is most evident when a link or switch is lost thru which ma ...
sfpsMcastConfigApiSndrAgeOut
This is the interval in seconds that the age timer runs. It is used to determine if a sender is still sending. After one age out interval, the sender is placed in a dying state and the local switch starts to listen for traffic from that sender on a spec ...
sfpsMcastConfigApiRefreshInterval
This is the interval at which sender announcements will be transmitted by the switch that the sender is locally attached. All sender refreshes will occur within 12 seconds. If this number is set to 60, 1/2 of the senders will be announced every 60 second ...
sfpsMcastConfigApiSndersPerAncmt
This is the number of sender announcements that will be made before the thread is released. Value will not take effect until blade is reset.
sfpsMcastConfigApiDebugLog
This value enables or disables extensive information logging in IGMP and MCAST generics. It is used in conjunction with the EventLogClient log flags. This value should be 0 unless extensive diagnostic information is required. This value is not persiste ...
sfpsMcastConfigApiStaticTblSize
This is the number of static entries that can be made to the sender database (multicast connection table). Typically there would be no entries in this table. Value will not take effect until blade is reset.
sfpsMcastConfigApiMcribSize
This is the number of static entries that can be made to the receiver database. Typically there would be very few entries in this table. Value will not take effect until blade is reset.
sfpsMcastConfigApiMcastMode
Multicast operates in three vlan checking modes. Mode 1 - Do no vlan checking. The sender and receivers do not have to be on the same vlan. Multicast connections in this mode disregard whether or not the sender or receiver is in a secure or open vlan. Mo ...
sfpsMcastConfigApiRemapDelay
When attempting to obtain a path from receiver to sender, a wait is sometimes incurred when pending on a switch resolve response. Additionally, when topology events occur that cause a redirection of the connection tree, time must be allowed for the topol ...
sfpsMcastConfigApiQHighLimit
The default for the High Query Rate is 100
sfpsMcastConfigApiQLowLimit
The default for the low query rate is 20
sfpsMcastConfigApiDynamicQuery
The default for the dynamic query is 1 (enabled)
sfpsMcastIPSIBTable
sfpsMcastIPSIBEntry
sfpsMcastIPSIBGroup
sfpsMcastIPSIBSender
sfpsMcastIPSIBInclusion
sfpsMcastIPSIBAge
sfpsMcastIPSibApiGroup
sfpsMcastIPSibApiSender
sfpsMcastIPSibApiVerb

You can start network devices monitoring using free 30-day trial version of IPHost Network Monitor right now. Witn IPHost SNMP monitor you can monitor network performance, audit network usage, detect network faults, or inappropriate access. The IPHost's SNMP monitor can communicate and interact with any SNMP-enabled device.

MIBs list