X-DDI-Concentrator-MIB Download

concMgmtType

concentrator.

concIpAddr

The concentrator's IP address.

concNetMask

The concentrator's subnet mask.

concBroadcast

The concentrator's broadcast address.

concTrapReceiverTable

This table lists the addresses of Network Management Stations that should receive trap messages from this concentrator when an exception condition occurs.

concTrapReceiverEntry

A trap receiver table entry.

concTrapReceiverType

corresponding entry from the concTrapReceiverTable. To add a new entry to the concTrapReceiverTable, set the concTrapReceiverAddr to an IpAddress which is not already in the table. The concTrapReceiverType for that entry is automatically set to other(1).

concTrapReceiverAddr

IP address for trap receiver.

concTrapReceiverComm

receiver.

concCommunityTable

table lists community strings and their access levels. When an SNMP message is received by this concentrator, the community string in the message is compared with this table to determine access rights of the sender.

concCommunityEntry

A community table entry.

concCommunityAccess

and write all objects in the MIB. A value of readWrite(3) allows the community to read and write all objects except the concCommunityTable, which it cannot access at all. A value of readOnly(2) allows the community to read all objects except the concComm ...

concCommunityString

defined by the value of concCommunityAccess.

concAttachType

attachment concentrator connected to the trunk ring, port 1 on the supervisor module (or single board concentrator) is configured as A and port 2 is configured as B. For a single attachment concentrator connected beneath another concentrator, port 2 is c ...

concTraffic

for the previous polling interval.

concReset

all modules in the concentrator.

concBaudRate

RS-232 port.

concInsertMode

The mode for inserting M-ports into the concentrator ring.

concClearMacTime

were last cleared. Writing a 0 to this object causes the mac counters to be cleared.

concClearPortTime

were last cleared. Writing a 0 to this object causes the port counters to be cleared.

concFddiRingTable

the nodes in the FDDI ring(s) to which the concentrator belongs.

concFddiRingEntry

A Fddi Ring table entry.

concFddiRingSMTIndex

The value of the SMT index associated with this ring.

concFddiRingAddress

The MAC address of this node in the FDDI ring.

concFddiRingNext

The MAC address of the next node in the FDDI ring.

chassisType

The chassis type.

chassisBkplType

The chassis backplane type.

chassisPs1Type

Type of power supply number 1.

chassisPs1Status

ok, the value of chassisPs1TestResult gives more detailed information about the power supply's failure condition(s).

chassisPs1TestResult

indicates that the supply passed all tests. Bits set in the result indicate error conditions.

chassisPs2Type

Type of power supply number 2.

chassisPs2Status

ok, the value of chassisPs2TestResult gives more detailed information about the power supply's failure condition(s).

chassisPs2TestResult

indicates that the supply passed all tests. Bits set in the result indicate error conditions.

chassisFanStatus

the value of chassisFanTestResult gives more detailed information about the fan's failure condition(s).

chassisFanTestResult

that the fan passed all tests. Bits set in the result indicate error conditions.

chassisMinorAlarm

The chassis minor alarm status.

chassisMajorAlarm

The chassis major alarm status.

chassisTempAlarm

The chassis temperature alarm status.

chassisNumSlots

The number of slots in the chassis for plug-in modules.

chassisSlotConfig

modules inserted. This is an integer value with bits set to indicate configured modules. It can be interpreted as a sum of f(x) as x goes from 1 to the number of slots, where f(x) = 0 for no module inserted and f(x) = exp(2, x-1) for a module inserted.

chassisModel

The manufacturer's model number for the chassis.

moduleTable

given by the value of chassisNumSlots.

moduleEntry

slot of the concentrator.

moduleIndex

This value is determined by the chassis slot number where the module is inserted. Valid entries are 1 to the value of chassisNumSlots

moduleType

The type of module.

moduleSerialNumber

The serial number of the module.

moduleHwHiVersion

For example, if the hardware version is 3.1, the value of moduleHwHiVersion is 3.

moduleHwLoVersion

For example, if the hardware version is 3.1, the value of moduleHwLoVersion is 1.

moduleFwHiVersion

example, if the firmware version is 3.1, the value of moduleFwHiVersion is 3.

moduleFwLoVersion

example, if the firmware version is 3.1, the value of moduleFwLoVersion is 1.

moduleSwHiVersion

example, if the software version is 3.1, the value of moduleSwHiVersion is 3.

moduleSwLoVersion

example, if the software version is 3.1, the value of moduleSwLoVersion is 1.

moduleStatus

is not ok, the value of moduleTestResult gives more detailed information about the module's failure condition(s).

moduleTestResult

indicates that the module passed all tests. Bits set in the result indicate error conditions.

moduleReset

control logic. This has the same affect as pressing the reset button on the module.

moduleName

to name the module.

moduleNumPorts

The number of ports supported by the module.

modulePortStatus

the module and each of the ports on the module. The first byte contains the status for the module (same value as moduleStatus), and subsequent bytes contain status for the first through the last ports on the module (same value as portStatus).

moduleSubType

The type of daughterboard attached to this module.

moduleModel

The manufacturer's model number for the module.

portTable

determined by the number of modules in the concentrator and the number of ports on each module.

portEntry

a module.

portModuleIndex

This value is determined by the chassis slot number which the module is plugged into. Valid entries are 1 to the value of chassisNumSlots.

portIndex

value is determined by the location of the port on the module. Valid entries are 1 to the value of moduleNumPorts for this module.

portFddiIndex

The snmpFddiPORTIndex for this module/port.

portName

to name the port.

portType

on the port.

portStatus

not ok, the values of snmpFddiPORTCEState and snmpFddiPORTConnectState give more detailed information about the port's failure condition(s).

portFddiSmtIndex

The snmpFddiPORTSMTIndex for this module/port.