Nortel-Magellan-Passport-VnetNisSigMIB Download

sigChanNisRowStatusTable

This entry controls the addition and deletion of sigChanNis components.

sigChanNisRowStatusEntry

A single entry in the table represents a single sigChanNis component.

sigChanNisRowStatus

This variable is used as the basis for SNMP naming of sigChanNis components. These components can be added and deleted.

sigChanNisComponentName

This variable provides the component's string name for use with the ASCII Console Interface

sigChanNisStorageType

This variable represents the storage type value for the sigChanNis tables.

sigChanNisIndex

This variable represents the index for the sigChanNis tables.

sigChanNisL2Table

This group specifies the provisionable layer 2 attributes of the Q.931 ITU-T protocol.

sigChanNisL2Entry

An entry in the sigChanNisL2Table.

sigChanNisT23

This attribute specifies the layer 2 enable request timer.

sigChanNisT200

This attribute specifies the maximum time between a layer 2 frame and its acknowledgment.

sigChanNisN200

This attribute specifies the maximum number of re-transmissions of a layer 2 frame.

sigChanNisT203

This attribute specifies the maximum time for which layer 2 frames may be absent. Expiry triggers a check on whether the far end is alive.

sigChanNisCircuitSwitchedK

This attribute specifies the maximum number of sequentially numbered I frames (that is, window size (k)) that may be unacknowledged at any given time for a SAP supporting primary rate (64kbit/sec) signalling.

sigChanNisL3Table

This group represents the provisionable Layer 3 timer attributes of a the Nis signalling protocol.

sigChanNisL3Entry

An entry in the sigChanNisL3Table.

sigChanNisT309

This attribute specifies the data link failure timer; used to ride out temporary failures.

sigChanNisT310

This attribute specifies the call proceeding state timer.

sigChanNisProvTable

This group defines the general options of the D-channel signalling link.

sigChanNisProvEntry

An entry in the sigChanNisProvTable.

sigChanNisSide

This attribute specifies whether the interface is the network or user side of the connection. The parameter applies to both the layer 2 and layer 3 of the interface. If this attribute is set to network, then the interface is master during channel negotiat ...

sigChanNisMaxNonCallConcurrent

This attribute specifies the maximum number of simultaneous active non-call messages that are allowed.

sigChanNisStateTable

This group contains the three OSI State attributes. The descriptions generically indicate what each state attribute implies about the component. Note that not all the values and state combinations described here are supported by every component which uses ...

sigChanNisStateEntry

An entry in the sigChanNisStateTable.

sigChanNisAdminState

This attribute indicates the OSI Administrative State of the component. The value locked indicates that the component is administratively prohibited from providing services for its users. A Lock or Lock - force command has been previously issued for this ...

sigChanNisOperationalState

This attribute indicates the OSI Operational State of the component. The value enabled indicates that the component is available for operation. Note that if adminState is locked, it would still not be providing service. The value disabled indicates that t ...

sigChanNisUsageState

This attribute indicates the OSI Usage State of the component. The value idle indicates that the component is not currently in use. The value active indicates that the component is in use and has spare capacity to provide for additional users. The value b ...

sigChanNisStatsTable

This group provides the operational components for the NisSig component.

sigChanNisStatsEntry

An entry in the sigChanNisStatsTable.

sigChanNisTotalCallsToIf

This attribute counts the total number of calls that have been made to the interface. The value wraps when it reaches its maximum.

sigChanNisTotalCallsFromIf

This attribute counts the total number of calls from the interface. The value wraps when it reaches its maximum.

sigChanNisNonCallAssocSessionsToIf

This attribute counts the total number of non-call associated sessions to the interface. The value wraps when it reaches its maximum.

sigChanNisNonCallAssocSessionsFromIf

This attribute counts the total number of non-call associated sessions from the interface. The value wraps when it reaches its maximum.

sigChanNisOperTable

This group provides the operational attributes for the NisSig protocol.

sigChanNisOperEntry

An entry in the sigChanNisOperTable.

sigChanNisActiveChannels

This attribute indicates the number of currently active channels. This includes data and voice channels.

sigChanNisActiveVoiceChannels

This attribute indicates the number of channels that are currently carrying voice.

sigChanNisActiveDataChannels

This attribute indicates the number of channels that are currently carrying data. This does not include modem data.

sigChanNisPeakActiveChannels

This attribute indicates the maximum number of channels that have been active on this signalling channel during the last polling period.

sigChanNisPeakActiveVoiceChannels

This attribute indicates the maximum number of voice channels that have been active on this signalling channel during the last polling period.

sigChanNisPeakActiveDataChannels

This attribute indicates the maximum number of data channels that have been active on this signalling channel during the last polling period.

sigChanNisDChanStatus

This attribute indicates the state of the D-channel. outOfService means that there is no layer 2 or layer 3 connectivity to the PBX. establishing means that the signalling channel is attempting to stage the layer 2. established means that the layer 2 is e ...

sigChanNisToolsTable

This contains a series of operational attributes which turn on and off several kinds of tracing.

sigChanNisToolsEntry

An entry in the sigChanNisToolsTable.

sigChanNisTracing

This attribute defines which types of tracing are active for this signalling channel. The tracing messages are sent to the debug stream. To see the messages the agentQueue attribute in Col/debug must be greater than 0 and a Telnet NMIS session must list ...

sigChanNisNisSpecificProvTable

This group provides NIS protocol specific provisioning.

sigChanNisNisSpecificProvEntry

An entry in the sigChanNisNisSpecificProvTable.

sigChanNisChanMaintenanceHandling

This attribute specifies how channel maintenance events should be handled upon startup. Channel maintenance events include locking and unlocking a channel or channel registration. The decision is either to send individual channel RESTART messages, SERVICE ...

sigChanNisFramerRowStatusTable

This entry controls the addition and deletion of sigChanNisFramer components.

sigChanNisFramerRowStatusEntry

A single entry in the table represents a single sigChanNisFramer component.

sigChanNisFramerRowStatus

This variable is used as the basis for SNMP naming of sigChanNisFramer components. These components cannot be added nor deleted.

sigChanNisFramerComponentName

This variable provides the component's string name for use with the ASCII Console Interface

sigChanNisFramerStorageType

This variable represents the storage type value for the sigChanNisFramer tables.

sigChanNisFramerIndex

This variable represents the index for the sigChanNisFramer tables.

sigChanNisFramerProvTable

This group contains the base provisioning data for the Framer component. Application or hardware interface specific provisioning data is contained in other provisionable Framer groups.

sigChanNisFramerProvEntry

An entry in the sigChanNisFramerProvTable.

sigChanNisFramerInterfaceName

This attribute contains a hardware component name. The attribute associates the application with a specific link. This defines the module processor on which Framer's parent component (as well as Framer itself) will run.

sigChanNisFramerStateTable

This group contains the three OSI State attributes. The descriptions generically indicate what each state attribute implies about the component. Note that not all the values and state combinations described here are supported by every component which uses ...

sigChanNisFramerStateEntry

An entry in the sigChanNisFramerStateTable.

sigChanNisFramerAdminState

This attribute indicates the OSI Administrative State of the component. The value locked indicates that the component is administratively prohibited from providing services for its users. A Lock or Lock - force command has been previously issued for this ...

sigChanNisFramerOperationalState

This attribute indicates the OSI Operational State of the component. The value enabled indicates that the component is available for operation. Note that if adminState is locked, it would still not be providing service. The value disabled indicates that t ...

sigChanNisFramerUsageState

This attribute indicates the OSI Usage State of the component. The value idle indicates that the component is not currently in use. The value active indicates that the component is in use and has spare capacity to provide for additional users. The value b ...

sigChanNisFramerStatsTable

This group contains the operational statistics data for a Framer component.

sigChanNisFramerStatsEntry

An entry in the sigChanNisFramerStatsTable.

sigChanNisFramerFrmToIf

This attribute counts the number of frames transmitted to the link interface by Framer. This count wraps to zero after reaching its maximum value.

sigChanNisFramerFrmFromIf

This attribute counts the number of frames received from the link interface by Framer. This count wraps to zero after reaching its maximum value.

sigChanNisFramerOctetFromIf

The number of bytes received from the link interface by Framer.

sigChanNisFramerAborts

This attribute counts the total number of aborts received. This count wraps to zero after reaching its maximum value.

sigChanNisFramerCrcErrors

This attribute counts the total number of frames with CRC errors. This count wraps to zero after reaching its maximum value.

sigChanNisFramerLrcErrors

This attribute counts the total number of frames with LRC errors. This count wraps to zero after reaching its maximum value.

sigChanNisFramerNonOctetErrors

This attribute counts the total number of frames that were non octet aligned. This count wraps to zero after reaching its maximum value.

sigChanNisFramerOverruns

This attribute counts the total number of frames received from the link for which overruns occurred. This count wraps to zero after reaching its maximum value.

sigChanNisFramerUnderruns

This attribute counts the total number of frames transmitted to the link for which underruns occurred. This count wraps to zero after reaching its maximum value.

sigChanNisFramerLargeFrmErrors

This attribute counts the total number of frames received which were too large (longer than 500 bytes). This count wraps to zero after reaching its maximum value.