Nortel-Magellan-Passport-UtpDpnTrunksMIB

Nortel-Magellan-Passport-UtpDpnTrunksMIB Download

MIBs list

The module describing the Nortel Magellan Passport UtpDpnTrunks Enterprise MIB.

IPHost Network Monitor offer an easy way of SNMP monitoring your Nortel network devices, Firewalls, Repeaters.

OID list for Nortel-Magellan-Passport-UtpDpnTrunksMIB

dpnGateUtpRowStatusTable
This entry controls the addition and deletion of dpnGateUtp components.
dpnGateUtpRowStatusEntry
A single entry in the table represents a single dpnGateUtp component.
dpnGateUtpRowStatus
This variable is used as the basis for SNMP naming of dpnGateUtp components. These components can be added and deleted.
dpnGateUtpComponentName
This variable provides the component's string name for use with the ASCII Console Interface
dpnGateUtpStorageType
This variable represents the storage type value for the dpnGateUtp tables.
dpnGateUtpIndex
This variable represents the index for the dpnGateUtp tables.
dpnGateUtpProvTable
This group of provisionable attributes contains the parameters used by Unacknowledged, Utp, and FrAccess for monitoring link quality.
dpnGateUtpProvEntry
An entry in the dpnGateUtpProvTable.
dpnGateUtpMaximumErroredInterval
This attribute specifies the interval time over which the error threshold (as specified by receiveErrorSensitivity) must be continuously exceeded before the Unacknowledged, Utp, or FrAccess component can be degraded. Once the error interval count exceeds ...
dpnGateUtpReceiveErrorSensitivity
This attribute is the allowable error rate beyond which the Unacknowledged, Utp, or FrAccess component can be degraded if it persists for a duration longer than the maximumErrorInterval. The threshold is expressed as a percentage of number of errored fram ...
dpnGateUtpStateTable
This group contains the three OSI State attributes and the six OSI Status attributes. The descriptions generically indicate what each attribute implies about the component. Note that not all the values and state combinations described here are supported b ...
dpnGateUtpStateEntry
An entry in the dpnGateUtpStateTable.
dpnGateUtpAdminState
This attribute indicates the OSI Administrative State of the component. The value locked indicates that the component is administratively prohibited from providing services for its users. A Lock or Lock - force command has been previously issued for this ...
dpnGateUtpOperationalState
This attribute indicates the OSI Operational State of the component. The value enabled indicates that the component is available for operation. Note that if adminState is locked, it would still not be providing service. The value disabled indicates that t ...
dpnGateUtpUsageState
This attribute indicates the OSI Usage State of the component. The value idle indicates that the component is not currently in use. The value active indicates that the component is in use and has spare capacity to provide for additional users. The value b ...
dpnGateUtpAvailabilityStatus
If supported by the component, this attribute indicates the OSI Availability status of the component. Note that, even though it is defined as a multi-valued set, at most one value is shown to the user. When no values are in the set, this indicates that ei ...
dpnGateUtpProceduralStatus
If supported by the component, this attribute indicates the OSI Procedural status of the component. Note that, even though it is defined as a multi-valued set, at most one value is shown to the user. When no values are in the set, this indicates that eith ...
dpnGateUtpControlStatus
If supported by the component, this attribute indicates the OSI Control status of the component. Note that, even though it is defined as a multi-valued set, at most one value is shown to the user. When no values are in the set, this indicates that either ...
dpnGateUtpAlarmStatus
If supported by the component, this attribute indicates the OSI Alarm status of the component. Note that, even though it is defined as a multi-valued set, at most one value is shown to the user. When no values are in the set, this indicates that either th ...
dpnGateUtpStandbyStatus
If supported by the component, this attribute indicates the OSI Standby status of the component. The value notSet indicates that either the attribute is not supported or that none of the status conditions described below are present. Note that this is a n ...
dpnGateUtpUnknownStatus
This attribute indicates the OSI Unknown status of the component. The value false indicates that all of the other OSI State and Status attribute values can be considered accurate. The value true indicates that the actual state of the component is not know ...
dpnGateUtpOpTable
This group of attributes contains the set of UTP operational parameters measured and maintained by this component.
dpnGateUtpOpEntry
An entry in the dpnGateUtpOpTable.
dpnGateUtpRoundTripDelay
This is the measured Round Trip Delay (ms) discovered with the remote through the UTP staging protocol. The value includes emission, propagation, and queuing delays. A 2 byte control frame is used to perform the measurement. A value of zero is displayed w ...
dpnGateUtpStatsTable
This group of attributes contains the set of Utp frame counters collected by this component.
dpnGateUtpStatsEntry
An entry in the dpnGateUtpStatsTable.
dpnGateUtpDiscardBadFromIf
This attribute is the number of received frames discarded by the Utp component. UTP discards any received frame that is unknown to its protocol. This counter wraps around to zero when the maximum value is reached.
dpnGateUtpDiscardExcessToIf
This attribute is the number of transmitted frames discarded by the Utp component. Transmitted frames are discarded if the wait for transmission queue is congested. This counter wraps around to zero when the maximum value is reached.
dpnGateUtpFrmRexmtToIf
This attribute is the number of frames retransmitted by the Utp component. This counter wraps around to zero when the maximum value is reached.
dpnGateUtpAreYouThereModeEntries
This attribute is the number of times the Utp component entered the AreYouThere mode. UTP enters this mode whenever the acknowledgment for the last transmitted frame has not been received within a certain time interval. In this mode UTP verifies that the ...
dpnGateUtpWindowClosures
This attribute is the number of times the Utp component closed its frame window. The frame window determines the maximum number of unacknowledged frames allowed. Typically, the frame window closes when the remote end cannot keep up with the frame arrival ...
dpnGateUtpFramerRowStatusTable
This entry controls the addition and deletion of dpnGateUtpFramer components.
dpnGateUtpFramerRowStatusEntry
A single entry in the table represents a single dpnGateUtpFramer component.
dpnGateUtpFramerRowStatus
This variable is used as the basis for SNMP naming of dpnGateUtpFramer components. These components cannot be added nor deleted.
dpnGateUtpFramerComponentName
This variable provides the component's string name for use with the ASCII Console Interface
dpnGateUtpFramerStorageType
This variable represents the storage type value for the dpnGateUtpFramer tables.
dpnGateUtpFramerIndex
This variable represents the index for the dpnGateUtpFramer tables.
dpnGateUtpFramerProvTable
This group contains the base provisioning data for the Framer component. Application or hardware interface specific provisioning data is contained in other provisionable Framer groups.
dpnGateUtpFramerProvEntry
An entry in the dpnGateUtpFramerProvTable.
dpnGateUtpFramerInterfaceName
This attribute contains a hardware component name. The attribute associates the application with a specific link. This defines the module processor on which Framer's parent component (as well as Framer itself) will run.
dpnGateUtpFramerLinkTable
This group contains attributes defining the framing of data on the link interface.
dpnGateUtpFramerLinkEntry
An entry in the dpnGateUtpFramerLinkTable.
dpnGateUtpFramerFramingType
This attribute defines the type of framing on the link.
dpnGateUtpFramerDataInversion
This attribute determines whether data bits are to be inverted (1 to 0 and 0 to 1) before transmission of frames to the interface. If the value of this attribute is On, the incoming data bits will also be inverted when frames are received from the link be ...
dpnGateUtpFramerFrameCrcType
This attribute defines the type of CRC used. The CRC value calculated is appended to the end of the frames transmitted to the link. The CRC value is removed from the end of frames received from the link and checked for correctness. NoCrc means that CRC is ...
dpnGateUtpFramerFlagsBetweenFrames
This attribute defines the number of flags that are inserted between frames sent to the link interface.
dpnGateUtpFramerStateTable
This group contains the three OSI State attributes. The descriptions generically indicate what each state attribute implies about the component. Note that not all the values and state combinations described here are supported by every component which uses ...
dpnGateUtpFramerStateEntry
An entry in the dpnGateUtpFramerStateTable.
dpnGateUtpFramerAdminState
This attribute indicates the OSI Administrative State of the component. The value locked indicates that the component is administratively prohibited from providing services for its users. A Lock or Lock - force command has been previously issued for this ...
dpnGateUtpFramerOperationalState
This attribute indicates the OSI Operational State of the component. The value enabled indicates that the component is available for operation. Note that if adminState is locked, it would still not be providing service. The value disabled indicates that t ...
dpnGateUtpFramerUsageState
This attribute indicates the OSI Usage State of the component. The value idle indicates that the component is not currently in use. The value active indicates that the component is in use and has spare capacity to provide for additional users. The value b ...
dpnGateUtpFramerStatsTable
This group contains the operational statistics data for a UTP Framer component.
dpnGateUtpFramerStatsEntry
An entry in the dpnGateUtpFramerStatsTable.
dpnGateUtpFramerFrmToIf
The number of frames transmitted to the link interface by Framer. Note: This does not include the number of frames transmitted directly to the hardware queue, thus bypassing the Framer component.
dpnGateUtpFramerFrmFromIf
The number of frames received from the link interface by Framer.
dpnGateUtpFramerOctetFromIf
The number of bytes received from the link interface by Framer.
dpnGateUtpFramerAborts
This attribute is the total number of aborts received.
dpnGateUtpFramerCrcErrors
This attribute is the total number of frames with CRC errors, occurring in the receive direction from the link.
dpnGateUtpFramerLrcErrors
This attribute is the total number of frames with LRC errors, occurring in the Tx link prior to transmission onto the link.
dpnGateUtpFramerNonOctetErrors
This attribute is the total number of frames that were non octet aligned.
dpnGateUtpFramerOverruns
This attribute is the total number of frames received from the link for which overruns occurred.
dpnGateUtpFramerUnderruns
This attribute is the total number of frames transmitted to the link for which underruns occurred.
dpnGateUtpFramerLargeFrmErrors
This attribute is the total number of frames received which were too large. The frame execeeded the maximumFrameLengthLimit provisioned attribute or it contained more than the 255 block hardware limit.
dpnGateUtpFramerFrmModeErrors
This attribute is the total number of frames detected with framing mode errors. A framingModeError is flagged when frames are inconsistent with the specified framingType, that is when interrupting frames are used while running in hdlc mode.
dpnGateUtpFramerOutOfSequenceFrm
This attribute is the total number of out of sequence frames in interrupting mode that have been received from the link.
dpnGateUtpFramerRepeatedFrm
This attribute is the total number of repeated frames (frames with the same sequence number) in interrupting mode that have been received from the link.
dpnGateUtpFramerUtilTable
This group contains the link utilization operational data for a Framer component.
dpnGateUtpFramerUtilEntry
An entry in the dpnGateUtpFramerUtilTable.
dpnGateUtpFramerNormPrioLinkUtilToIf
This attribute is the utilization of the normal and high priority data traffic (interruptable traffic) sent to the link as a percentage of the available bandwidth on the link. Note that this includes traffic with Transfer Priorities (TP) of 0, 6 and 9 and ...
dpnGateUtpFramerHighPrioLinkUtilToIf
This attribute is the utilization of the interrupting priority data traffic sent to the link as a percentage of the available bandwidth on the link. Note that this includes traffic with a Transfer Priority (TP) of 11 and/or Emission Priority of 1. The uti ...
dpnGateUtpFramerNormPrioLinkUtilFromIf
This attribute is the utilization of the normal and high priority data traffic (interruptable traffic) received from the link as a percentage of the available bandwidth on the link. Note that this includes traffic with Transfer Priorities (TP) of 0, 6 and ...
dpnGateUtpFramerHighPrioLinkUtilFromIf
This attribute is the utilization of the interrupting priority data (interrupting traffic) received from the link as a percentage of the available bandwidth on the link. Note that this includes traffic with a Transfer Priority (TP) of 11 and/or Emission P ...
dpnGateUtpFramerUtilThresholdTable
This group contains all of the provisioning data required to set the link utilization alarm thresholds. All thresholds are percentages which can take on any value in the range of 0% through 100%. The value 100% is used to disable an individual threshold. ...
dpnGateUtpFramerUtilThresholdEntry
An entry in the dpnGateUtpFramerUtilThresholdTable.
dpnGateUtpFramerMinorLinkUtilAlarmThreshold
This attribute provides the threshold value which defines when a minor alarm would be issued, denoting a sustained total average link utilization. The total average link utilization is calculated based on the number of received bytes. The Set alarm is iss ...
dpnGateUtpFramerMajorLinkUtilAlarmThreshold
This attribute provides the threshold value which defines when a major alarm would be issued, denoting a sustained total average link utilization. The total average link utilization is calculated based on the number of received bytes. The Set alarm is iss ...
dpnGateUtpFramerCriticalLinkUtilAlarmThreshold
This attribute provides the threshold value which defines when a critical alarm would be issued, denoting a sustained total average link utilization. The total average link utilization is calculated based on the number of received bytes. The Set alarm is ...
dpnGateUtpFramerLinkUtilAlarmStatus
This attribute provides control of the generation of link utilization alarms. If the value is disabled, none of the alarms are generated (this is equivalent to setting all of the thresholds to 100%). If the value is enabled, the individual thresholds are ...

Download IPHost Network Monitor (500 monitors for 30 days, 50 monitors free forever) to start monitoring network devices right now.

MIBs list