LANOPTICS-RING-MANAGER-MIB Download

rmServerReportingTo

This gives the IP address for the reporting manager.

rmRingStatus

This variable indicates the curent ring status.

rmServerHealthText

This variable describes the status of the ring server in a textural manner.

rmServerHealth

This variable will describe the status of the ring server.

rmRingEventInLog

The number of events currently in the internal event log.

rmRingEventTable

A table containing the last events. The detailed structure is TBD.

rmRingEventEntry

An entry containing one event. The index into the table is the event number (32 bits int), where each byte represented by an index digit.

rmRingEvent

This variable will give the data structure describing a ring event in an internal format

rmRingBeaconingStatus

This variable will give the data structure describing the beaconing state of the ring.

rmRingIsoErrorStatus

This variable will give the data structure describing the isolating error state of the ring.

rmRingSingleStationStatus

This variable will give the data structure describing the single station state of the ring.

rmRingFullConfiguration

This variable gives the ring configuration as known to the server. Each MAC address is represented by 6 bytes. The direction is up-stream.

rmRingConfigurationUpdate

This variable will give a sequence of changes in the ring configuration for the monitored ring.

rmServerInitProcess

This variable will initialize the server (reset the management module).

rmServerAdminState

This variable will indicate administrative status of the server. IDLE - 0 The bit # (LSB = 0): REM - bit 0 on CRS - bit 1 on RPS - bit 2 on LBS - bit 3 on

rmServerOperatingState

This variable will indicate operating status of the server: IDLE - all 0 The bit # (LSB = 0): REM - bit 0 on CRS - bit 1 on RPS - bit 2 on LBS - bit 3 on

rmServerAdminParameters

The required bit per event disabled/enabled. The bit # (LSB = 0): Nullevent(0), Nodenoresponseevent(1), Pollprocessfailevent(2), Criticnodejoinedringevent(3), Noderemovedevent(4), Activemonitorerrorevent(5), Newactivemonitorevent(6), Naunchangeevent(7), C ...

rmServerOperatingParameters

The required bit per event disabled/enabled. The bit # (LSB = 0): Nullevent(0), Nodenoresponseevent(1), Pollprocessfailevent(2), Criticnodejoinedringevent(3), Noderemovedevent(4), Activemonitorerrorevent(5), Newactivemonitorevent(6), Naunchangeevent(7), C ...

rmDeviceStatusTable

A table containing device parameters and configuration.

rmDeviceEntry

An entry containing device parameters and configuration. The index to the table is the MAC address of the device.

rmDeviceMacAddress

rmDeviceUpstream

rmDeviceAdminState

The required state of the adapter. - only removed is supported.

rmDeviceOperateState

The operating state of the adapter.

rmDevicePhysLocation

rmDeviceGroupAddress

rmDeviceFunctionAddress

rmDeviceProductID

rmDeviceStationID

rmDeviceStationStatus

rmDeviceFunctionClass

rmDeviceAccessPriority

rmDeviceMicroLevel

rmDeviceMonitored

rmDeviceDaysAllowed

rmDeviceHoursAllowed

rmRingPollProcessStatus

This variable will give the data structure describing the poll process status of the ring.

rmRingIsoImpendingThreshold

--This variable will give the isolating soft error --mpending threshold. --This variable will give the isolating soft error --xcessive threshold. --This variable will give the isolating soft error --ecrement value. --This variable will give the isolating ...

rmRingSoftErrorTimer

This variable will give the ring soft error timer (in units of 10 milliseconds).

rmRingIsolatingTab

This variable will give the ring isolating table.

rmRingCongestTab

This variable will give the ring congestion table.

rmRingNonIsolatingTab

This variable will give the ring non isolating table.

rmRingExcToNormal

--This variable will give the ring excessive to --ormal threshold. --This variable will give the ring impending to --ormal threshold. This variable will enable/disable auto removal of a node when the isolating threshold is exceeded or the congestion thres ...

rmRingAllowedDaysPartition1

This variable is the first partition in the days time exis. The partitions define ranges in units of days in which some device are allowed to enter the ring and some are not.

rmRingAllowedDaysPartition2

This variable is the second partition in the days time exis. The partitions define ranges in units of days in which some devices are allowed to enter the ring and some are not. The value should be higher than Partition1

rmRingAllowedHoursPartition1

This variable is the first partition in the hours time exis. The partitions define ranges in units of hours (1-24 hours) in which some devices are allowed to enter the ring and some are not.

rmRingAllowedHoursPartition2

This variable is the second partition in the hours time exis. The partitions define ranges in units of hours (1-24 hours) in which some devices are allowed to enter the ring and some are not. The value should be higher than Partition1.

rmServerPowerOn

This variable indicates if the server is powered on since the last poll.

rmTRLastErrorClass

This var contains the error class of the last Token-Ring error reported by the agent.

rmTRLastErrorType

This var contains the error type of the last Token-Ring error, depending on the error class

rmTRFaultDomainNode1

This var contains the MAC address of the first node in the last error fault domain.

rmTRFaultDomainNode2

This var contains the MAC address of the second node in the last error fault domain.

rmIsoTresholdExceededCount

This var counts the total number that Isloating Treshold has been exceeded (exessive error status of the ring) since the agent is up or reset.

rmNonIsoTresholdExceededCount

This var counts the total number that Non Isloating Treshold has been exceeded since the agent is up.

rmCongestionTresholdExceededCount

This var counts the total number that Congestion Treshold has been exceeded since the agent is up.

rmBeaconCounter

This var counts the total number of Beacons for the whole ring since the agent is up.

rmSpareCounter

Spare Counter for future use

rmPurgeCounter

This var counts the total number of ring Purges since the agent is up.

rmClaimCounter

This var counts the total number of Token Claims since the agent is up.

rmAdapterResetCounter

This var counts the total number of times the agent adapter has to reset itself since the agent is up.

rmLostFramesCounter

This var counts the total number of Lost Frames events for the whole ring since the agent is up.

rmCongestionCounter

This var counts the total number of Congestion events for the whole ring since the agent is up.

rmFrameCopyCounter

This var counts the total number of Frame Copy events for the whole ring since the agent is up.

rmFrequencyErrorCounter

This var counts the total number of Frequency Error events for the whole ring since the agent is up.

rmTokenCounter

This var counts the total number of Token error events for the whole ring since the agent is up.

rmLineCounter

This var counts the total number of Line error events for the whole ring since the agent is up.

rmInternalCounter

This var counts the total number of Internal error events for the whole ring since the agent is up.

rmBurstCounter

This var counts the total number of Burst error events for the whole ring since the agent is up.

rmARIFCICounter

This var counts the total number of ARI/FCI events for the whole ring since the agent is up.

rmAbortCounter

This var counts the total number of Abort events for the whole ring since the agent is up.

rmPollFailCounter

This var counts the total number of Poll Failed events for the whole ring since the agent is up.

rmNoResponseCounter

This var counts the total number of No Response events for the whole ring since the agent is up.

rmWholeRingCounters

This var counts a list of all the above counters (52-71) for convenience. Each counter occupies 32 bits of this structure in the order of the related variables. For internal use only.

rmResetOldDevicesSetup

This var resets existing agent setup for all devices, e.g: monitored, not-allowed, etc.

rmResetErrorCounters

This var resets existing agent error counters.

rmSetCurrentTime

This var sets the current time (for security settings). The time is the number of seconds elapsed since midnight, December 31, 1899.

rmRingFirstSplitConfiguration

This variable will give the first part of the ring configuration upto 256 bytes including header (for agents with limited buffer for a single octet). Retrieving this variable and several 'nexts' enables to compose the whole ring configuration.

rmRingNextSplitConfiguration

This variable will give the next part of the ring configuration relating to rmRingFirstSplitConfiguration or previous variable of this type. Upto 256 bytes are given (for agents with limited buffer for a single octet). See previous variable for more detai ...