FH800u-MIB Download
IPHost Network Monitor offer an easy way of SNMP monitoring your Allied Telesis network devices,
Firewalls, Repeaters.
OID list for FH800u-MIB
- stackInusedIP
- The IP address currently used by the Dual-Speed Hub system.
- stackInusedNetMask
- The subnet maskcurrently used by the Dual-Speed Hub system.
- stackInusedGateway
- The prefered gateway used to send traps.
- stackInusedServerSlipAddr
- system.
- stackInusedHostSlipAddr
- system.
- stackInusedBootUpIP
- system. The Bootup IP must reside in the same subnet as the stackIP.
- stackTemporalIP
- Used to change the IP address of the Dual-Speed Hub system.
- stackTemporalNetMask
- Used to change the subnet mask of the Dual-Speed Hub system.
- stackTemporalGateway
- Used to change the prefered gateway to send traps.
- stackTemporalServerSlipAddr
- system. The SLIP address must reside in the same subnet as the stackIP.
- stackTemporalHostSlipAddr
- system.
- stackTemporalBootUpIP
- system. The Bootup IP must reside in the same subnet as the stackIP.
- ipInformationReset
- Setting the stackIP, stackNetMask,stackGateway, stackSlipAddr, and stackBootUpIP will not immediately enable parameters take effect . They will take effect when ipInformationReset is set to reset(2).
- stackHealthMonitor
- < FOR fh800u Dual-Speed Hub DEFINITION : > There are two kinds of hubs : 12 ports need (1+ 12 + 1 + 1 + 1 + 1 +1 +1 +1) 20 bytes and 24 ports need (1+ 24 + 1 + 1 + 1 + 1 +1 +1 +1) 32 bytes The maximun size : 256 bytes (total for 8 hubs)=8 hub * (1+ 24 + ...
- groupTable
- A group means a hub unit
- groupEntry
- groupID
- The ID number of a hub unit, used to select it
- groupType
- Type of hub unit
- groupCounterReset
- Write any value to this variable to reset the counters of the hub unit. 2 is a value commonly used to reset things
- groupPosition
- Physical position of a hub unit in top-down order, only supported if hardware permits such as Dual-Speed Hub systems
- groupRptrHwVer
- Hardware version of the repeater board.
- groupRptrSerialNo
- Serial number of the repeater board.
- groupSysMajorVer
- Microcode major version of this hub.
- groupSysMinorVer
- Microcode minor version of this hub.
- groupPostCodeMajorVer
- POST microcode major version of this hub.
- groupPostCodeMinorVer
- POST microcode minor version of this hub.
- groupAgentStatus
- an SNMP primary agent. primary(2): The agent in this stack is a primary agent. backup(3): The agent in this stack is a backup agent.
- groupAgentHwVer
- Hardware version of the agent board.
- groupAgentSerialNo
- Serial number of the agent board.
- groupAgentPhysAddr
- MAC address of this hub agent
- groupAgentBootupOption
- in the segment. normal(1): Use NVRAM information and flash ROM microcode to start up the system. tftp-download(2): Always download the new version of microcode into RAM and start it. bootp-get-ip(3): Get the IP information from the BootP server, and then ...
- groupAgentBaudrate
- Baud rate of the console port
- portTable
- information about ports in a system. Each port belongs to a group.
- portEntry
- portGroupID
- ID of the hub unit
- portID
- ID of the port unit
- portSpeed
- Ethernet connector type of a port
- portSpeedConfig
- Select the Ethernet connector type of a port
- portSegmtID
- ID of the Segment unit
- nicAttachSegment
- attached to.
- fullRmonSegment
- only 4 rmon groups.
- rmonConfigTable
- ID of of the segment the rmon montioring .
- rmonConfigEntry
- rmonConfigSegmtID
- ID of the Segment rmon is montioring.
- rmonConfigStatus
- Status of this RMON segment.
- perfMonSegmentTable
- perfMonSegmentEntry
- segmentPerfID
- ID used to select a segment
- segmentCRCErrors
- Total CRC errors received by a segment.
- segmentAlignmentErrors
- segment
- segmentCollisions
- Total collisions received in a segment
- segmentTotalPortIsolates
- Total isolated ports in a segment.
- segmentSymbolErrors
- Total frame symbol errors received by a segment
- switchPortStatsTable
- This table provides statistics on each port on each switch module in the stack. Note that statistics for the external port on media and switch/media modules are unavailable to the agent and are reported as 0. Statistics for port 2 (the internal 10Mbps p ...
- switchPortStatsEntry
- switchPortStatsGroupID
- The group ID of the switch module port being referenced. If the group is not present, or if there is no switch module installed in the group, GetRequests and SetRequests are rejected with an error-status of noSuchName(2). GetNextRequests skip entries fo ...
- switchPortStatsID
- The port ID of the switch module port being referenced. Port 1 is always the internal 100Mbps port. Port 2 is always the internal 10Mbps port. Port 3 is always the external port. Note that port 2 is inactive on media modules and port 3 is inactive on ...
- switchPortReadableFrames
- The number of valid frames received by the port.
- switchPortReadableOctets
- The number of octets (bytes) in all valid frames received by the port.
- switchPortFCSErrors
- The number of valid-length frames received by the port that had FCS (frame check sequence) errors.
- switchPortAlignmentErrors
- The number of valid-length frames received by the port that had alignment errors.
- switchPortFramesTooLong
- The number of frames received by the port that were longer than 1518 bytes.
- switchPortShortEvents
- The number of frames received by the port that were shorter than 82 bits.
- switchPortRunts
- The number of frames received by the port that were longer than 82 bits but shorter than 512 bits (64 bytes).
- switchPortCollisions
- The number of collisions detected on the port.
- switchPortLateEvents
- The number of collisions detected on the port that occurred later than 512 bit-times into the transmission of a packet.
- switchPortVeryLongEvents
- The number of times any activity continued for more than 4 to 7.5 milliseconds.
- switchPortDataRateMismatches
- The number of times the incoming data rate mismatched the local clock source enough to cause a FIFO overflow or underflow.
- switchPortBroadcastPackets
- The number of good broadcast frames received by the port.
- switchPortMulticastPackets
- The number of good multicast (not broadcast) frames received by the port.
- backupPortTableSize
- Table size of backup port pairs. Backup table index. Hub ID of the primary port. Port number of the primary port. Hub ID of the secondary port. Port number of the secondary port. -- port function for this backup port pair. Setting this objec ...
- securityPortEntry
- securityPortGroupID
- ID of a hub unit
- securityPortID
- Port ID in a hub unit
- securityPortAddr
- MAC address
- securityAutoLearnAction
- auto-learn function for the physical address authorized access to this port. Once this object is set to active(2), the agent will set the authorized address to 0 first and then start the auto-learn process, and the hub will begin to read the source addre ...
- securityPortIntrusion
- or inactive
Download IPHost Network Monitor (500 monitors for 30 days, 50 monitors free forever) to start monitoring network devices right now.
