MIBs list

This MIB is for managing information required to route messages transported over Signalling System No. 7 (SS7) Network via Cisco IP Transfer Point. The Cisco IP Transfer Point (ITP) is a hardware and software solution that transports SS7 traffic using IP. Each ITP node provides the functions necessary to act as a SS7 signalling point. Each signalling point is connected to other signalling point using IP based or traditional TDM links.

IPHost Network Monitor offer an easy way of SNMP monitoring your Cisco Servers, Routers, Switches, Bridges, Firewalls, Repeaters.


The value of sysUpTime at the time of the last creation or deletion of an entry in the cItpRouteTable. If the local network management subsystem is re-initialization, then this object contains the sysUpTime at the time when this occurred. This value can b ...
The value of sysUpTime at the time of the last load of the route table using file format.
The status of the current load or status from the prior load operation. This object will have a value of loadInProgress while the load operation is in progress. The cItpRtConfigLoad contains a timestamp indicating when the load operation completed.
A count of the number of routes that have changed states. This value is incremented whenever the destination state of a route changes. This value is used to provide an indicator of the stability of the routing table information.
A control to enable or disable cItpRouteStateChange notifications as follows: 'true' Indicates that the cItpRouteStateChange notification should be generated when the state of any route changes. That is, the notification generation is enabled. 'false' In ...
This object specifies the maximum amount of time to delay before generating the cItpRouteStateChange notification. The delay is introduced to allow multiple route state changes to be bundled into a single notification. If the value of this object is equal ...
The maximum number of dynamic SS7 routes. This object is used to limit the size of the route table by preventing unbounded growth of dynamic entries. Dynamic entries are created when certain MTP3 management messages are received or sent. The removal of dy ...
This object specifies the time interval used to monitor the rate of route state changes notifications. This object in combination with cItpRtChangeNotifMaxPerWindow are used to determine the notification transit rate and suppress route state notification ...
This object specifies the maximum number of route state changes that can occur in the time interval specified in the cItpRtChangeNotifMaxPerWindow object. If additional state changes can occur in the specified time interval the notifications are suppress ...
The route table for determining the linkset that a packet must traverse to arrive at its destination node given by the destination point code.
Each table entry represents a configured route statement.
The configured name for this route table.
The destination point code.
The cost assigned to this linkset matching this route. Higher numbers represent higher cost.
The linkset that the packet is to be forwarded to on matching this route.
The mask used to define which part of cItpRouteDpc is significant when comparing the cItpRouteDpc to the destination code point in the packet to be routed.
The quality of service classification to be assigned to the ip packets used to transport the SS7 messages. The value to specify for packets when they will be transported on SCTP/IP based linkset.
List of the possible route status values. 'unknown' : Status can not be determined. 'available' : Route is available. 'restricted' : Traffic is restricted on route. 'unavailable' : Route is unable to service traffic.
List of the possible non-adjacent status values. 'unknown' : Status can not be determined. 'allowed' : traffic is allowed. 'restricted' : Traffic is restricted on route. 'prohibited' : Route is prohibited from providing traffic.
A flag to indicate whether cItpRouteStateChange notifications have been suppressed in the current time interval specified by the cItpRtChangeNotifWindowTime object. 'true' Indicates that the device has suppressed the sending of cItpRouteStateChange notif ...
This object contains a list of route state changes accumulated until the list is full or the time time interval specified in cItpRtChangeNotifDelayTime has passed. It consists of one or more tuples packed together in the format of '......
Route scalars Group.
Route table group.
Route revision one scalars group.

Download IPHost Network Monitor (500 monitors for 30 days, 50 monitors free forever) to start monitoring network devices right now.

MIBs list