ADTRAN-ATLAS-T1-MIB Download
This MIB defines a generic ATLAS T1 interface.
IPHost Network Monitor offer an easy way of SNMP monitoring your ADTRAN Servers, Routers, Switches, Bridges,
Firewalls, Repeaters.
OID list for ADTRAN-ATLAS-T1-MIB
- adATLAST1IfNumber
- The number of T1 ports (regardless of their current state) present on this system.
- adATLAST1IfTable
- The Atlas T1 Interface Status Table
- adATLAST1IfEntry
- An entry in the Atlas T1 Interface Status Table
- adATLAST1IfIndex
- This variable indicates the interface number of a particular T1 port within the ATLAS product. This number will be the same as the ifIndex located in the MIB-II interface table.
- adATLAST1IfSlotNum
- This variable indicates the slot number of a particular ATLAS module with a T1 interface.
- adATLAST1IfPortNum
- This variable indicates the port number of a particular T1 interface on an ATLAS module.
- adATLAST1IfAlarmStatus
- This variable shows the status of each alarm by setting a bit. If the bit is set the alarm is active. Multiple bits can be set at one time. Bit # ALARM ------ ----- 0x01 LOS 0x02 Red 0x04 Yellow 0x08 Blue 0x10 DS0
- adATLAST1IfRxLevel
- This variable represents the recieved signal strength in dB.
- adATLAST1IfCurrentLOFC
- This variable indicates the value of the loss of frame count for the current 15 minute interval.
- adATLAST1IfTotalLOFC
- This variable indicates the value of the loss of frame count for the current 24 hours.
- adATLAST1IfResetPRMStats
- This variable resets the performance monitoring statistics for all of the intervals: current, 15 min, and total.
- adATLAST1IfIntervalTable
- The Atlas T1 Interface Interval Performance Table
- adATLAST1IfIntervalEntry
- An entry in the Atlas T1 Interface Interval Performance Table
- adATLAST1IfIntervalIndex
- This variable indicates the interface number of a particular T1 port within the ATLAS product. This number will be the same as the ifIndex located in the MIB-II interface table.
- adATLAST1IfIntervalNumber
- A number between 1 and 96, where 1 is the most recently completed 15 minute interval and 96 is the least recently completed 15 minutes inter- val (assuming that all 96 intervals are valid).
- adATLAST1IfIntervalLOFC
- The Loss of Frame Count encountered by a DS1 interface in one of the previous 96, individual 15 minute, intervals.
- adATLAST1IfDS0Table
- The Atlas T1 Interface DS0 Table
- adATLAST1IfDS0Entry
- An entry in the Atlas T1 Interface DS0 Table
- adATLAST1IfDS0Index
- This variable indicates the interface number of a particular T1 port within the ATLAS product. This number will be the same as the ifIndex located in the MIB-II interface table.
- adATLAST1IfDS0Status
- This variable shows the overall status of each DS0. There are 24 octets, each corresponding to a single DS0. These are the values for the different status states in each octet: Value(decimal) Status -------------- ------ 0 Unal ...
- adATLAST1IfDS0Alarm
- This variable shows the overall alarm status of each DS0. There are 24 octets, each corresponding to a single DS0. These are the values for the different alarm states in each octet: Value(decimal) Alarm -------------- ------ 0 ...
- adATLAST1IfDS0RxSignalStatusA
- This variable shows the status of the receive signal's A bit in each DS0. There are 24 octets, each corresponding to a single DS0. These are the values for the different status states in each octet: Value(decimal) Status -------------- ------ 0 ...
- adATLAST1IfDS0RxSignalStatusB
- This variable shows the status of the receive signal's B bit in each DS0. There are 24 octets, each corresponding to a single DS0. These are the values for the different status states in each octet: Value(decimal) Status -------------- ------ 0 ...
- adATLAST1IfDS0TxSignalStatusA
- This variable shows the status of the transmit signal's A bit in each DS0. There are 24 octets, each corresponding to a single DS0. These are the values for the different status states in each octet: Value(decimal) Status -------------- ------ ...
- adATLAST1IfDS0TxSignalStatusB
- This variable shows the status of the transmit signal's B bit in each DS0. There are 24 octets, each corresponding to a single DS0. These are the values for the different status states in each octet: Value(decimal) Status -------------- ------ ...
- adATLAST1TstTable
- The Atlas T1 Test Table
- adATLAST1TstEntry
- An entry in the Atlas T1 Test Table
- adATLAST1TstIndex
- This variable indicates the interface number of a particular T1 port within the ATLAS product. This number will be the same as the ifIndex located in the MIB-II interface table.
- adATLAST1TstLocalLpBk
- This variable sets the status of the local loopback for sending test signals.
- adATLAST1TstRemoteLpBk
- This variable sets the status of the remote loopback for sending test signals.
- adATLAST1TstRemoteLpBkStatus
- This variable indicates the current remote loopback status.
- adATLAST1TstPattern
- This variable sets the pattern to be sent for testing.
- adATLAST1TstPatternSync
- This variable shows whether there is sync between transmitting and recieving the test pattern.
- adATLAST1TstPatternSyncLost
- This variable shows whether sync has been lost since it was last cleared.
- adATLAST1TstPatternESs
- This variable shows the amount of errored seconds since it was last cleared.
- adATLAST1TstPatternBESs
- This variable shows the amount of bursty errored seconds since it was last cleared.
- adATLAST1TstPatternSESs
- This variable shows the amount of severely errored seconds since it was last cleared.
- adATLAST1TstClearResults
- This variable is used to clear the results of the test.
- adATLAST1TstInjectError
- This variable is used to inject an error in the test pattern.
Download IPHost Network Monitor (500 monitors for 30 days, 50 monitors free forever) to start monitoring network devices right now.
