ctels100-ng-mib

ctels100-ng-mib Download

MIBs list

This module provides authoritative definitions for part of the naming tree below: cabletron { enterprises 52 }

You can select a variable to monitor using the built-in IPHost SNMP MIB browser that provides you with all variables, their current values and descriptions taken from the ctels100-ng-mib .

OID list for ctels100-ng-mib

els100SysSerialno
The serial number of the system.
els100SysTftpIPAddress
The IP address of the TFTP server from which a software download is to be initiated. This variable must be set before a TFTP download can be started with the els100SysTftpStartDownload variable.
els100SysTftpFilename
The name of the software upgrade file residing on the TFTP server. Path information must be included in the file name. This variable must be set before a TFTP download can be started with the els100SysTftpStartDownload variable.
els100SysPowerupCount
The total number of times the system has powered up since it was shipped from the factory.
els100SysBrcastCutoffRate
The Broadcast Cutoff Rate of the switch allowing for the control of broadcast storms. The value of this variable sets a per second rate. If the broadcast and unknown destination address frames being forwarded through the system surpass this rate, they are ...
els100SysGatewayIPAddress
The IP address of the next hop router (gateway) to which frames destined for an IP subnet different than what the system resides are sent.
els100SysTftpStartDownload
Start a TFTP download. A SET of this variable with the value download (1) initiates a TFTP download to upgrade the system software. The variables els100SysTftpIPAddress and els100SysTftpFilename must be configured before a download can begin. A GET of thi ...
els100SysBootPDhcpEnable
Enable or disable the operation of the BootP and DHCP protocols on the system. These protocols are used for automatically configuring the system's IP address information if a properly configured BootP and/or DHCP server exists on the network.
els100SysSyslogServer
The IP address of the Syslog Server.
els100SysLowestSyslogSeverity
The Lowest Syslog Severity Level. All logs with the same or higher severity will be delivered. Note: higher severity has lower number.
els100SysComPortEnable
The administrative state of the Com Port.
els100SysBoardID
The system board ID.
els100PortTable
The port table.
els100PortEntry
An entry in the port table.
els100Port
The number of the port, from 1 to the number of ports on the system.
els100PortStatus
The connection (link) status of the port, either up (linked) or down (not linked).
els100PortDuplexStatus
The duplex status of the port, either half duplex or full duplex.
els100PortForwardedFrames
The number of frames received on the port and forwarded to another port on the system module for processing.
els100PortRcvdLocalFrames
The number of frames received where the destination is on the port.
els100PortName
A descriptive string of up to 60 characters used by the network administrator to name the port.
els100PortEnable
The enable status of the port, either enable or disable.
els100PortSpeed
The speed the port is operating at: 10Mbps, or 100Mbps, or 1000Mbps.
els100PortAutonegEnable
The auto-negotiation status of the port, either enable or disable. When in the enable (2) state, the port will automatically configure its duplex and speed operation.
els100PortFlowControlEnable
The state of flow control operation of the port, either enable or disable.
els100PortType
Port physical interface type.
els100SwitchIPAddress
The IP address of the system.
els100SwitchSubnetMask
The subnet mask associated with the IP address of the system.
els100ActiveAgingTime
The aging time of entries in the MAC address forwarding table of the system.
els100SwitchTrapRcvr1
The IP address of the first SNMP manager to which traps from the system are directed.
els100SwitchTrapCommunity1
The community name of the first SNMP manager to which traps from the system are directed.
els100SwitchTrapRcvr2
The IP address of the second SNMP manager to which traps from the system are directed.
els100SwitchTrapCommunity2
The community name of the second SNMP manager to which traps from the system are directed.
els100SwitchTrapRcvr3
The IP address of the third SNMP manager to which traps from the system are directed.
els100SwitchTrapCommunity3
The community name of the third SNMP manager to which traps from the system are directed.
els100SwitchTrapRcvr4
The IP address of the fourth SNMP manager to which traps from the system are directed.
els100SwitchTrapCommunity4
The community name of the fourth SNMP manager to which traps from the system are directed.
els100SwitchPortMirroringStatus
The Port Mirroring status of the system, either disable or enable.
els100SwitchMirroredPort
The port that is being mirrored - the source.
els100SwitchMirroringPort
The port that is mirroring - the destination.
els100SwitchXmitMirrorEnable
Enable or disable the mirroring of transmitted traffic out the mirrored port to the mirroring port.
els100SwitchRcvMirrorEnable
Enable or disable the mirroring of received traffic into the mirrored port to the mirroring port.
els100SwitchVlanEnable
Globally enable or disable the VLAN operation of the system.
els100SwitchVlanConfigTable
The VLAN configuration table.
els100SwitchVlanEntry
An entry in the VLAN configuration table.
els100SwitchVlanId
The number of the VLAN, from 1 to the number of VLAN's supported on the system.
els100SwitchVlanName
A descriptive string of up to 60 characters used by the network administrator to name the VLAN.
els100SwitchVlanPorts
The set of ports in the VLAN. For systems supporting tagged VLAN's, these are the ports to which packets on the VLAN are sent untagged. Each octet within the value of this object specifies a set of eight ports, with the first octet specifying ports 1 thro ...
els100SwitchVlanEgressPorts
The set of ports defined to be on other VLAN's to which tagged packets destined for this specific VLAN should also be sent. Thus, this variable defines ports on the system that reach stations downstream which are on this VLAN and to which traffic may be f ...
els100SwitchVlanStatus
Control variable used to enable or disable the operation of the associated VLAN in the system.
els100SwitchVlanPortTable
The VLAN port configuration table.
els100SwitchVlanPortEntry
An entry in the VLAN port configuration table.
els100SwitchVlanPortId
The number of the port, from 1 to number of ports in the system.
els100SwitchVlanPvid
The port's VLAN ID. For tagged VLAN's, this variable defines a 12 bit port VLAN ID (PVID) used as the identifier of the VLAN in the packet tag.
els100SwitchVlanPortType
For tagged VLAN's, the VLAN port type, either hybrid or access. Hybrid ports allow both tagged and untagged packets to enter the switch. Access ports only accept untagged packets.
els100SwitchPriorityEnable
Globally enable or disable the Class of Service traffic priority mechanism for the system.
els100SwitchPriorityThreshold
The global priority threshold level for the system at which VLAN tagged frames entering the associated port are assigned a high priority. This variable can have a value from (0...7). Traffic with a priority level equal to or above this value are high prio ...
els100SwitchPriorityPortTable
The priority port table.
els100SwitchPriorityPortEntry
An entry in the port priority table.
els100SwitchPriorityPortId
The port number, from 1 to number of ports in the system.
els100SwitchPriorityDefault
The port priority level assigned to untagged traffic entering the associated port. This variable can have a value in the range (0...7). This value is compared to the value of the els100SwitchPriorityThreshold variable to determine if the traffic on the po ...
els100SwitchSpanningTreeStandby
Globally enable or disable Spanning Tree Standby. If set to disable, every port will instanly enter forwarding mode after link up

You can start network devices monitoring using free 30-day trial version of IPHost Network Monitor right now. Witn IPHost SNMP monitor you can monitor network performance, audit network usage, detect network faults, or inappropriate access. The IPHost's SNMP monitor can communicate and interact with any SNMP-enabled device.

MIBs list