CISCO-VISM-MODULE-MIB Download

vismCPUUtilization

This is the percentage of time CPU is in non-idle state. DEFVAL { 0 } ::= { vismSystemPerfStats 1 } SYNTAX Integer32 (0..100) MAX-ACCESS read-only STATUS current DESCRIPTION This is the percentage of memory in use by VISM. DEFVAL { 0 } ::= { vismS ...

vismVoIpDtmfRelay

This attribute defines whether the DTMF (Dual Tone Multi-Frequency) digits need to be transported to the other endpoint via NSE(Named Signal Event) packets. DEFVAL { true } ::= { vismVoIpGrp 5 } SYNTAX TruthValue MAX-ACCESS read-write STATUS curre ...

vismVoIpLapdTrunkPVC

This object should be used for VoIP Trunking applications and only if the signaling type is configured to be CCS(Common Channel Signaling). By default the PRI(Primary Rate Interface) D-channel information will be sent on the control channel. If the contro ...

vismSplModemToneBitMap

This bit map is applicable for any special modem tones that need to be enabled or disabled on the module. If a bit is set to 1, the tone detection is enabled. If the bit is set to 0, the tone detection is disabled. The values mean: vism1560980Tone: 1560/ ...

vismSSRCEnable

This object is used to enable/disable more than one SSRC (Synchronization Source) per RTP session. When set to true, the module will accept more than one SSRC per RTP session. When set to false, the module will not allow more than one SSRC per RTP session ...

vismOamLoopbackSetCLP

This object is used to set the cell loss priority of the oam loopback cell for all the PVCs. If set to true, all the CLP bits will be set to 1. If set to false, all the CLP bits will be set to 0. DEFVAL { true } ::= { vismSystemGrp 45 } SYNTAX Truth ...

vismPvcAlarmLogAdminTimer

This object specifies the time for which the detailed alarm logging for all the PVCs on the module will remain active. The value in this object can be set and is valid only if vismPvcAlarmLogEnable is set to true. If this object is set to 0, it indicates ...

vismPvcAlarmLogOperTimer

This object specifies the time remaining in minutes for which the detailed alarm logging will remain enabled on all the PVCs on the module. When this value becomes 0, it indicates that all the PVCs on the module have run through the time specified in vism ...

vismContinuityCheckCellEnable

This object is used to enable/disable the continuity check cell for all the PVCs on the module. If set to true, the module will transmit continuity check cells. If set to false, the module will disable the cell transmission. DEFVAL { true } ::= { vismSys ...

ciscoVismPerfStatsGroup

The collection of objects which are used to represent VISM performance statistics.

ciscoVismCallStatsGroup

The collection of objects which are used to represent VISM Call Statistics.

ciscoVismIpGroup

This group contains objects that are specific to IP.

ciscoVismVoIpGroup

This group contains objects that are specific to VoIP.

ciscoVismDspGroup

This group contains objects that are used to manage DSPs on the VISM card.

ciscoVismSystemGroup

This group contains objects that are specific to the card.

ciscoVismInteropGroup

This group contains objects which will enhance the interoperability functionalities of VISM.

ciscoVismTrapObjGroup

This group contains objects that are defined for the purpose of sending in trap varbinds.

ciscoVismAal2Group

This group contains objects which will enhance the interoperability functionalities of VISM.

ciscoVismDspDeprecatedGroup

The collection of objects that were supported earlier but deprecated now.

ciscoVismSystemDeprecatedGroup

The collection of objects that were supported earlier but deprecated now.

ciscoVismVoIpDeprecateGroup

The collection of objects that were supported earlier but deprecated now.

ciscoVismSystemGroup1

This group contains objects that are specific to the card.

ciscoVismSystemFeatureGroup

This group contains specific card level objects for feature support on the module.

ciscoVismTrapVarbindGroup

This group contains objects that are defined for the purpose of sending in trap varbinds.

ciscoVismSystemFeatureGroupRev1

This group contains specific card level objects for feature support on the module.

ciscoVismSystemGroupSup1

This group contains objects that are specific to the card.

ciscoVismDspGroupSup1

This group contains objects that are used to manage DSPs on the VISM card.