CISCO-RHINO-MIB

CISCO-RHINO-MIB Download

MIBs list

IPHost Network Monitor offer an easy way of SNMP monitoring your Cisco Servers, Routers, Switches, Bridges, Firewalls, Repeaters.

OID list for CISCO-RHINO-MIB

ciscoLS1010ChassisSysType
The chassis system type.
ciscoLS1010ChassisBkplType
The chassis backplane type.
ciscoLS1010ChassisPs0Type
Type of power supply number 1.
ciscoLS1010ChassisPs0AdminStatus
Enable or disable power supply 1.
ciscoLS1010ChassisPs0Status
Status of power supply number 1.
ciscoLS1010ChassisPs0Led
LED Status of power supply number 1.
ciscoLS1010ChassisPs1Type
Type of power supply number 2.
ciscoLS1010ChassisPs1AdminStatus
Enable or disable power supply 2.
ciscoLS1010ChassisPs1Status
Status of power supply number 2.
ciscoLS1010ChassisPs1Led
LED Status of power supply number 2.
ciscoLS1010ChassisFanStatus
Status of the chassis fan.
ciscoLS1010ChassisFanLed
LED Status of fan.
ciscoLS1010ChassisCardStatusLed
LED Status of CPU card.
ciscoLS1010ChassisEnetLinkLed
Ethernet link status LED of CPU card.
ciscoLS1010Chassis12VoltStatus
The chassis 12V status.
ciscoLS1010ChassisTempStatus
The values of minorWarning(3), majorWarning(4) and criticalWarning(5) will be primarily used by C6400 to indicate the core temperature. C6400 will never report overTemperature(2) status. In C6400 there are two temperature sensors: core and inlet. C6400 us ...
ciscoLS1010ChassisPcmciaSlot0Type
Type of PCMCIA slot 0 type.
ciscoLS1010ChassisPcmciaSlot1Type
Type of PCMCIA slot 1 type.
ciscoLS1010ChassisNumSlots
The number of slots in the chassis for plug-in modules.
ciscoLS1010ChassisLastChange
The last time chassis physical content get changed.
ciscoLS1010ChassisFailureAction
which includes either power supply, voltage, temperature and fan failure.
ciscoLS1010ChassisChangeAction
which includes either power supply, fan and boards.
ciscoLS1010ChassisClockingMode
the mode is non-revertive, which means that the clock will stick to the current priority, even though higher priority clock is available.
ciscols1010SystemClockSourceStatus
The network clock source status of 'system' source: 'notSelected' indicates 'system' not selected as the network clock source. 'selected' indicates ASP freerunning(system) is selected as network clock source.
ciscols1010SystemClockSourcePriority
The highest priority at which 'system' is configured as a network clock source.
ciscoLS1010ChassisInletTempStatus
inlet. C6400 use this object to represent the inlet temperature and use the object ciscoLS1010ChassisTempStatus to represent the core temperature.
ciscoLS1010ModuleTable
given by the value of ciscoLS1010ChassisNumSlots.
ciscoLS1010ModuleEntry
slot of the chassis.
ciscoLS1010ModuleIndex
A unique value for each module.
ciscoLS1010ModuleType
The type of module.
ciscoLS1010ModuleSerialNumber
Deprecated in favor of object ciscoLS1010ModuleSerialNumberString. This object returns 0 for modules using an alphanumeric numbering scheme.
ciscoLS1010ModuleHwVersion
The hardware version of the module.
ciscoLS1010ModuleSwVersion
The software version number.
ciscoLS1010ModuleDescr
to describe the module.
ciscoLS1010ModuleNumSubModules
The max number of sub-modules supported by this module.
ciscoLS1010ModuleAdminStatus
ok(1). Setting this object to one of the acceptable values gives the following results: reset: reset the module's control logic enable: enable the module disable: disable the module Setting this object to any other values results in an error.
ciscoLS1010ModuleOperStatus
Operational status of the module.
ciscoLS1010ModuleHwVersionMinor
The minor hardware version of the module.
ciscoLS1010ModuleSerialNumberString
The serial number of the module.
ciscoLS1010SubModuleTable
given by the value of ciscoLS1010SlotNumSubModules.
ciscoLS1010SubModuleEntry
sub-slot of the module.
ciscoLS1010SubModuleIndex
This value is determined by sub-slot number where the sub-module is inserted.
ciscoLS1010SubModuleType
The type of sub-module.
ciscoLS1010SubModuleSerialNumber
Deprecated in favor of object ciscoLS1010SubModuleSerialNumberString. This object returns 0 for submodules using an alphanumeric numbering scheme.
ciscoLS1010SubModuleHwVersion
Together with ciscoLS1010SubModuleHwVersionMinor, this completely specifies the hardware version of the sub-module.
ciscoLS1010SubModuleSwVersion
The software version number.
ciscoLS1010SubModuleDescr
to describe the module.
ciscoLS1010SubModuleNumPorts
this sub-module.
ciscoLS1010SubModuleAdminStatus
This object can be read/written as reset or ok.
ciscoLS1010SubModuleHwVersionMinor
Together with ciscoLS1010SubModuleHwVersion, this completely specifies the hardware version of the sub-module.
ciscoLS1010SubModuleOperStatus
Operational status of the submodule.
ciscoLS1010SubModuleSerialNumberString
The serial number of the sub-module.
ciscoLS1010PortTable
determined by the number of modules in the chassis, the number of sub-module in the module and the number of ports on each sub-module.
ciscoLS1010PortEntry
a sub-module.
ciscoLS1010PortIndex
a sub-module. The value is determined by the location of the port on the sub-module. Valid entries are 1 to the value of subModuleNumPorts for this sub-module.
ciscoLS1010PortIfIndex
The ifIndex value assigned to this port.
clsEnetPortTable
is mainly to support ethernet port only.
clsEnetPortEntry
ethernet port.
clsEnetPortDuplex
in half-duplex, full-duplex, or auto mode. If the port could not agree with the far end on port duplex, the port will be in auto(2) mode. Unknown(1) indicates either the port does not support duplex mode, or the duplex mode is none of the defined.
clsEnetPortAdminSpeed
in bits per second. The current operational speed of the port is determined by ifSpeed. If the port could not agree with the far end on port speed, the port will be in auto(2) mode, which will force the port to transmit in speed whichever is lower. Unknow ...
clsEnetPortType
interface on the port. unknown(1) indicates that the port type is none of those defined. empty(6) indicates that the port is not present.
clsEnetPortLinkStatus
of the port came up. autoNegotiate(2) -- the port will try to negotiate the link with the partner port. If successful, the link will come up, otherwise the link will remain down. forceUp(3) -- the port will force the link up irrespective of its partner po ...
clsPortLedTable
A list of LED entries associated with a port.
clsPortLedEntry
LED associated with a particular port which is identified by ifIndex.
clsPortLedIndex
among all the LEDs associated with the port identified by ifIndex. This value is related to the physical location of the LED, and is in ascending order from top to bottom, left to right.
clsPortLedType
Indicates the type or label of the LED.
clsPortLedStatus
Unknown(1) indicates either the LED status is not supported or the status is none of the defined.
ciscoAtmCpuAdminStatus
Reset will reload the CPU board.
ciscoAtmSwitchTotalBuffer
The total cell buffer count in switch's shared memory.
ciscoAtmSwitchFreeBuffer
The free cell buffer count in switch's shared memory.
ciscoAtmSwitchDiscardCells
The total discarded cells of the switch.
ciscoAtmSwitchInvalidCells
The total invalid cells of the switch.
ciscoAtmSwitchInvalidCellHeaderTable
A list of invalid cell header entries.
ciscoAtmSwitchInvalidCellHeaderEntry
a entry of invalid cell header.
ciscoAtmSwitchInvalidCellHeaderIndex
entry in the table.
ciscoAtmSwitchInvalidCellHeader
octet 0 is port number (0-32), octet 1 bit 7-5 is PTI, octet 1 bit 4 is CLP, octet 1 bit 3-0 is GFC, octet 2 is VPI, octet 3 is high byte of VCI octet 4 is low byte of VCI.
ciscoAtmCpuTerminateOamFlow
Terminate all the incoming OAM cells to the CPU port.
ciscoAtmInterceptEndToEndOamFlow
cells are sent to the switch CPU. If the value is 'true', all incoming end-to-end OAM flow cells, including those on transit connections, are sent to the switch CPU. This value may be modified at any time. The modified value will apply to all existing con ...
ciscoLS1010ChassisMIBGroup
A collection of objects providing rhino chassis information
ciscoLS1010ChassisMIBObsoleteGroup
A collection of objects providing rhino chassis information which are obsolete.
ciscoLS1010ChassisMIBRev1Group
A collection of objects useful for reporting the hardware version of sub-modules in the chassis.
ciscoLS1010ChassisMIBClockingGroup
A collection of objects useful for managing clocking.
ciscoLS1010ChassisMIBGroup1
A collection of objects for managing the LS1010 chassis.
clsEnetPortGroup1
A collection of objects for managing ethernet ports.
clsPortLedGroup1
A collection of objects for showing port LEDs.
clsOperStatusGroup
A collection of objects for displaying operational status of modules and sub-modules in the chassis.
clsInletTempGroup
A collection of objects for reporting inlet temperature.
ciscoLS1010ChassisMIBGroup2
A collection of objects for managing the LS1010 chassis.
ciscoLS1010ChassisMIBDeprecatedGroup
A collection of objects providing rhino chassis information which are obsolete.

Download IPHost Network Monitor (500 monitors for 30 days, 50 monitors free forever) to start monitoring network devices right now.

MIBs list