CISCO-IF-EXTENSION-MIB Download

ciscoIfExtensionAsymmetricalSpeedGroup

An optional group used to provide information on asymmetrical interface speeds.

cieIfPacketStatsTable

This table contains interface packet statistics which are not available in IF-MIB(RFC2863). As an example, some interfaces to which objects in this table are applicable are as follows : o Ethernet o FastEthernet o ATM o BRI o Sonet o GigabitEthernet Some ...

cieIfPacketStatsEntry

An entry into the cieIfPacketStatsTable.

cieIfLastInTime

This object represents the elapsed time in milliseconds since last protocol input packet was received. Discontinuities in the value of this variable can occur at re-initialization of the management system, and at other times as indicated by the values of ...

cieIfLastOutTime

This object represents the elapsed time in milliseconds since last protocol output packet was transmitted. Discontinuities in the value of this variable can occur at re-initialization of the management system, and at other times as indicated by the value ...

cieIfLastOutHangTime

This object represents the elapsed time in milliseconds since last protocol output packet could not be successfully transmitted. Discontinuities in the value of this variable can occur at re-initialization of the management system, and at other times a ...

cieIfInRuntsErrs

The number of packets input on a particular physical interface which were dropped as they were smaller than the minimum allowable physical media limit. Discontinuities in the value of this variable can occur at re-initialization of the management system, ...

cieIfInGiantsErrs

The number of input packets on a particular physical interface which were dropped as they were larger than the ifMtu (largest permitted size of a packet which can be sent/received on an interface). Discontinuities in the value of this variable can occur ...

cieIfInFramingErrs

The number of input packets on a physical interface which were misaligned or had framing errors. This happens when the format of the incoming packet on a physical interface is incorrect. Discontinuities in the value of this variable can occur at re-initia ...

cieIfInOverrunErrs

The number of input packets which arrived on a particular physical interface which were too quick for the hardware to receive and hence the receiver ran out of buffers. Discontinuities in the value of this variable can occur at re-initialization of the ma ...

cieIfInIgnored

The number of input packets which were simply ignored by this physical interface due to insufficient resources to handle the incoming packets. For example, this could indicate that the input receive buffers are not available or that the receiver lost a pa ...

cieIfInAbortErrs

Number of input packets which were dropped because the receiver aborted. Examples of this could be when an abort sequence aborted the input frame or when there is a collision in an ethernet segment. Discontinuities in the value of this variable can occur ...

cieIfInputQueueDrops

The number of input packets which were dropped. Some reasons why this object could be incremented are: o Input queue is full. o Errors at the receiver hardware while receiving the packet. Discontinuities in the value of this variable can occur at re-ini ...

cieIfOutputQueueDrops

This object indicates the number of output packets dropped by the interface even though no error had been detected to prevent them being transmitted. The packet could be dropped for many reasons, which could range from the interface being down to errors ...

cieIfPacketDiscontinuityTime

The value of sysUpTime on the most recent occasion at which this interface's counters suffered a discontinuity. If no such discontinuities have occurred since the last re-initialization of the local management subsystem, then this object contains a value ...

cieIfInterfaceTable

This table contains objects which provide more information about interface properties not available in IF-MIB (RFC 2863). Some objects defined in this table may be applicable to physical interfaces only. As a result, this table may be sparse for logical ...

cieIfInterfaceEntry

An entry into the cieIfInterfaceTable.

cieIfResetCount

The number of times the interface was internally reset and brought up. Some of the actions which can cause this counter to increment are : o Bringing an interface up using the interface CLI command. o Clearing the interface with the exec CLI command. o ...

cieIfKeepAliveEnabled

A keepalive is a small, layer-2 message that is transmitted by a network device to let directly-connected network devices know of its presence. This object returns 'true' if keepalives are enabled on this interface. If keepalives are not enabled, 'false' ...

cieIfStateChangeReason

This object displays a human-readable textual string which describes the cause of the last state change of the interface. Examples of the values this object can take are: o 'Lost Carrier' o 'administratively down' o 'up' o 'down'

cieIfCarrierTransitionCount

Number of times interface saw the carrier signal transition. For example, if a T1 line is unplugged, then framer will detect the loss of signal (LOS) on the line and will count it as a transition. Discontinuities in the value of this variable can occur a ...

cieIfInterfaceDiscontinuityTime

The value of sysUpTime on the most recent occasion at which this interface's counters suffered a discontinuity. If no such discontinuities have occurred since the last re-initialization of the local management subsystem, then this object contains a valu ...

cieIfDhcpMode

The DHCP mode configured by the administrator. If 'true' the DHCP is enabled. In which case an IP address is requested in DHCP. This is in addition to any that are configured by the administrator in 'ciiIPAddressTable' or 'ciiIPIfAddressTable' in CISCO-IP ...

cieIfMtu

The MTU configured by the administrator. This object is exactly same as 'ifMtu' in ifTable from IF-MIB for the same ifIndex value , except that it is configurable by the administrator. For more description of this object refer to 'ifMtu' in IF-MIB.

cieIfContextName

The ContextName denotes the interface 'context' and is used to logically separate the MIB management. RFC 2571 and RFC 2737 describe this approach. When the agent supports a different SNMP context, as detailed in RFC 2571 and RFC 2737, for different inter ...

cieIfOperStatusCause

This object represents the detailed operational cause reason for the current operational state of the interface. The current operational state of the interface is given by the 'ifOperStatus' defined in IF-MIB. The corresponding instance of 'cieIfOperStatu ...

cieIfOperStatusCauseDescr

The description for the cause of current operational state of the interface, given by the object 'cieIfOperStatusCause'. For an interface whose 'ifOperStatus' is not 'down' the value of this object will be 'none'.

cieIfSpeedReceive

An estimate of the interface's current receive bandwidth in bits per second. This object is provided for interface with asymmetric interface speeds like ADSL and should be used in conjunction with ifSpeed object. For interfaces which do not vary in band ...

cieIfHighSpeedReceive

An estimate of the interface's current receive bandwidth in units of 1,000,000 bits per second. If this object reports a value of `n' then the speed of the interface is somewhere in the range of `n-500,000' to `n+499,999'. For interfaces which do not va ...

cieIfOwner

This data type is used to model an administratively assigned name of the current owner of the interface resource. This information is taken from the NVT ASCII character set. It is suggested that this name contain one or more of the following: SnmpEngineI ...

cieIfSharedConfig

This object indicates the current configuration of interface sharing on the given interface. 'notApplicable' - the interface sharing configuration on this interface is not applicable. 'ownerDedicated' - the interface is in the dedicated mode to the bindin ...

cieIfSpeedGroupConfig

This object specifies the current speed group configuration on the given interface. 'notApplicable' - the interface speed group configuration on this interface is not applicable. It is a read-only value. '10G' - the interface speed group configuration on ...

cieIfStatusListTable

This table contains objects for providing the 'ifIndex', interface operational mode and interface operational cause for all the interfaces in the modules. This table contains one entry for each 64 interfaces in an module. This table provides efficient way ...

cieIfStatusListEntry

Each entry represents the 'ifIndex', interface operational mode and interface operational cause for a set of 64 interfaces in a module.

cieIfStatusListIndex

An arbitrary integer value, greater than zero, which identifies a list of 64 interfaces within a module.

cieInterfacesIndex

This object represents the 'ifIndex' for a set of 64 interfaces in the module.

cieInterfacesOperMode

This object represents the operational mode for a set of 64 interfaces in the module.

cieInterfacesOperCause

This object represents the operational status cause for a set of 64 interfaces in the module.

cieInterfaceOwnershipBitmap

This object indicates the status for a set of 64 interfaces in a module regarding whether or not each interface is administratively assigned a name of the current owner of the interface resource as per cieIfOwner.

cieIfVlStatsTable

This table contains VL (Virtual Link) statistics for a capable interface. Objects defined in this table may be applicable to physical interfaces only.

cieIfVlStatsEntry

Each row contains managed objects for Virtual Link statistics on interface capable of providing this information.

cieIfNoDropVlInPkts

This object indicates the number of input packets on all No-Drop Virtual Links belonged to this interface.

cieIfNoDropVlInOctets

This object indicates the number of input octets on all No-Drop Virtual Links belonged to this interface.

cieIfNoDropVlOutPkts

This object indicates the number of output packets on all No-Drop Virtual Links belonged to this interface.

cieIfNoDropVlOutOctets

This object indicates the number of output octets on all No-Drop Virtual Links belonged to this interface.

cieIfDropVlInPkts

This object indicates the number of input packets on all Drop Virtual Links belonged to this interface.

cieIfDropVlInOctets

This object indicates the number of input octets on all Drop Virtual Links belonged to this interface.

cieIfDropVlOutPkts

This object indicates the number of output packets on all Drop Virtual Links belonged to this interface.

cieIfDropVlOutOctets

This object indicates the number of output octets on all Drop Virtual Links belonged to this interface.

cieSystemMtu

Global system MTU in octets. This object specifies the MTU on all interfaces. However, the value specified by cieIfMtu takes precedence for an interface, which means that the interface's MTU uses the value specified by cieIfMtu, if it is configured.

cieLinkUpDownEnable

Indicates whether cieLinkUp/cieLinkDown or standard mib-II defined linkUp/Down or both, notifications should be generated for the interfaces in the system. 'standard' - only generate standard defined mib-II linkUp/linkDown notification if 'ifLinkUpDownTr ...

cieStandardLinkUpDownVarbinds

Indicates whether to send the extra varbinds in addition to the varbinds defined in linkUp/linkDown notifications. 'standard' - only send the varbinds defined in the standard linkUp/linkDown notification. 'additional' - send the extra varbinds in additi ...

cieIfIndexPersistence

This object specifies whether ifIndex values persist across reinitialization of the device. ifIndex persistence means that the mapping between the ifDescr object values and the ifIndex object values will be retained across reboots. Applications such as de ...

cieIfIndexPersistenceTable

This table lists configuration data relating to ifIndex persistence. This table has a sparse dependent relationship on the ifTable, containing a row for each ifEntry corresponding to an interface for which ifIndex persistence is supported.

cieIfIndexPersistenceEntry

Each entry represents ifindex persistence configuration for an interface specified by ifIndex. Whenever an interface which supports ifindex persistence is created/destroyed in the ifTable, the corresponding ifindex persistence entry is created/destroyed r ...

cieIfIndexPersistenceEnabled

This object specifies whether the interface's ifIndex value persist across reinitialization. Due to change in syntax, this object is deprecated by cieIfIndexPersistenceControl.

cieIfIndexPersistenceControl

This object specifies whether the interface's ifIndex value persist across reinitialization. In global state, the interface uses the global setting data for persistence i.e. cieIfIndexGlobalPersistence.

cieDelayedLinkUpDownNotifEnable

This object specifies whether the system generates a cieDelayedLinkUpDownNotif notification.

cieDelayedLinkUpDownNotifDelay

This object specifies the interval of time an interface's operational status must remain stable following a transition before the system will generate a cieDelayedLinkUpDownNotif.

cieIfIndexGlobalPersistence

This object specifies whether ifIndex values persist across reinitialization of the device. ifIndex persistence means that the mapping between the ifDescr object values and the ifIndex object values will be retained across reboots. Applications such as de ...

cieIfDot1qCustomEtherTypeTable

A list of the interfaces that support the 802.1q custom Ethertype feature.

cieIfDot1qCustomEtherTypeEntry

An entry containing the custom EtherType information for the interface. Only interfaces with custom 802.1q ethertype control are listed in the table.

cieIfDot1qCustomAdminEtherType

The Dot1qEtherType allow administrator to select a non-standard (other than 0x8100) 2-byte ethertype for the interface to interoperate with third party vendor's system that do not use the standard 0x8100 ethertype to identify 802.1q-tagged frames. The cur ...

cieIfDot1qCustomOperEtherType

The current operational value of the 802.1q ethertype for the interface.

cieIfUtilTable

This table contains the interface utilization rates for inbound and outbound traffic on an interface.

cieIfUtilEntry

An entry containing utilization rates for the interface. Every interface for which the inbound and outbound traffic information is available has a corresponding entry in this table.

cieIfInPktRate

By default, this is the five minute exponentially-decayed moving average of the inbound packet rate for this interface. However, if the corresponding instance of cieIfInterval is instantiated with a value which specifies an interval different from 5-minut ...

cieIfInOctetRate

By default, this is the five minute exponentially-decayed moving average of the inbound octet rate for this interface. However, if the corresponding instance of cieIfInterval is instantiated with a value which specifies an interval different from 5-minute ...

cieIfOutPktRate

By default, this is the five minute exponentially-decayed moving average of the outbound packet rate for this interface. However, if the corresponding instance of cieIfInterval is instantiated with a value which specifies an interval different from 5-minu ...

cieIfOutOctetRate

By default, this is the five minute exponentially-decayed moving average of the outbound octet rate for this interface. However, if the corresponding instance of cieIfInterval is instantiated with a value which specifies an interval different from 5-minut ...

cieIfInterval

This object specifies the time interval over which the inbound and outbound traffic rates are calculated for this interface.

cieIfDot1dBaseMappingTable

This table contains the mappings of the ifIndex of an interface to its corresponding dot1dBasePort value.

cieIfDot1dBaseMappingEntry

An entry containing the mapping between the ifIndex value of an interface and its corresponding dot1dBasePort value. Every interface which has been assigned a dot1dBasePort value by the system has a corresponding entry in this table.

cieIfDot1dBaseMappingPort

The dot1dBasePort value for this interface.

cieIfNameMappingTable

This table contains objects for providing the 'ifName' to 'ifIndex' mapping. This table contains one entry for each valid 'ifName' available in the system. Upon the first request, the implementation of this table will get all the available ifNames, and it ...

cieIfNameMappingEntry

An entry into the cieIfNameMappingTable.

cieIfName

Represents an interface name mentioned in the 'ifName' object of this system.

cieIfIndex

This object represents the 'ifIndex' corresponding to the interface name mentioned in the 'cieIfName' object of this instance. If the 'ifName' mentioned in the 'cieIfName' object of this instance corresponds to multiple 'ifIndex' values, then the value of ...

ciscoIfExtensionTablePacketGroup

A collection of objects containing packet statistics for a given interface.

ciscoIfExtensionTableIntfGroup

A collection of objects containing information about properties of interfaces.

ciscoIfExtensionTableIntfGroup1

A collection of objects containing information about properties of interfaces.

ciscoIfExtensionSystemGroup

A collection of objects providing global system-wise information about interfaces.

ciscoIfExtDot1qEtherTypeGroup

A collection of objects providing the information about 802.1q custom EtherType on the interface.

ciscoIfExtUtilizationGroup

A collection of objects containing information about utilization rates of interfaces.

ciscoIfExtDot1dBaseMappingGroup

A collection of objects containing mapping information about the ifIndex values of interfaces and their dot1dBasePort values.

ciscoIfExtIfNameMappingGroup

A collection of objects for the 'ifName' to 'ifIndex' mapping.

ciscoIfExtensionTableIntfGroup2

A collection of objects containing information about properties of interfaces.

cieIfStatusListGroup

A collection of objects containing information about set of interfaces.

cieLinkUpDownNotifEnableGroup

A collection of objects to control 'cieLinkUp/cieLinkDown' and standard mib-II defined 'linkUp/linkDown' notifications.

ciscoIfExtUtilIntervalGroup

A collection of objects containing information about calculation interval for utilization rate on interfaces.

cieIfIndexPersistenceGroup

A collection of objects containing information about ifIndex Persistence of interfaces. Since cieIfIndexPersistence and cieIfIndexPersistenceEnabled are deprecated, so, cieIfIndexPersistenceGroup containing these two objects are deprecated by cieIfIndexPe ...

cieDelayedLinkUpDownNotifNotifEnableGroup

The group of objects that help configure the cieDelayedLinkUpDownNotif on the system.

cieIfIndexPersistenceControlGroup

A collection of objects containing information about ifIndex Persistence of interfaces.

ciscoIfExtensionTableIntfGroup3

A collection of objects containing information about properties of interfaces.

cieIfStatusListGroupSup1

Additional objects containing information about a set of interfaces.

cieIfVlStatsGroup

Objects containing information about a VL (Virtual Link) statistics on an interface.

ciscoIfExtensionTableIntfGroup3SupR01

This group is supplement to ciscoIfExtensionTableIntfGroup3.